Mason-Lite MFP39VF Manual del propietario

Report No. 08-154

Do not store or use gasoline or other

ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from

a neighbor’s phone and follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the re department.

Installation and service must be performed

by a qualied installer, service agency, or

the gas supplier.

WARNING:

If the information in these instructions is

not followed exactly, a re or explosion may

result causing property damage, personal

injury or death.

This rebox has been tested and approved

by PFS-TECO under ANSI Z21.91 for use

with any ANSI Z21.11.2 approved gas logs.

IMPORTANT:

READ THESE INSTRUCTIONS CAREFULLY

BEFORE STARTING INSTALLATION OF

THIS FIREPLACE.

Do not store gasoline or other ammable

vapors and liquids in the vicinity of this or any

other appliance.

FOR USE ONLY WITH A LISTED GAS-FIRED

UNVENTED DECORATIVE ROOM HEATER

NOT TO EXCEED 40,000 BTU/H.

DO NOT BUILD A WOOD FIRE.

Carefully review the instructions supplied

with the decorative type unvented room

heater for the minimum replace size

requirement.

DO NOT INSTALL AN APPLIANCE IN THIS

FIREBOX UNLESS THIS FIREBOX MEETS

THE MINIMUM DIMENSIONS REQUIRED

FOR THE INSTALLATION.

INSTALLER:Leave this manual with the

appliance.

CONSUMER: Retain this manual for future

reference.

Installation and Operation

Instructions

Vent Free Universal Masonry Firebox

Models MFP39/44/49VF

mason-lite.com

TABLE OF CONTENTS

EXAMPLE LABEL.

Below is a sample picture of the rating plate that is located inside the lower dome side of your replace. Model Number, Date

of Manufacture and Serial Number should be stamped on the plate where indicated.

Cover Page..........................................................................................................1

Table of contents................................................................................................2

Example Rating Label......................................................................................2

Fireplace Parts Diagram ....................................................................................3

Customer Service & Replacement Parts..........................................................3

General Information ........................................................................................... 4

Introduction .....................................................................................................4

Before Beginning the Installation .....................................................................4

Statement of Intended Use ..............................................................................4

Product Overview.............................................................................................4

Firebox Dimensions ......................................................................................... 4

Safety Information.........................................................................................5 - 6

Carbon Monoxide Poisoning............................................................................5

General Safety Concerns.................................................................................5

Installing Television (TV) Above Fireplace .......................................................6

Location...............................................................................................................7

Typical Installations..........................................................................................7

Framing Dimensions ........................................................................................ 7

Seismic & Non-Seismic Code ..........................................................................7

Supporting Floor System...................................................................................8

Floor Framing...................................................................................................8

Rebar Locations...............................................................................................8

Wood Floor .........................................................................................................8

Crawl Space or Upper Floor.............................................................................8

Weight Determination ........................................................................................9

Other Weight Considerations...........................................................................9

Clearances .................................................................................................10 - 11

The Importance of Clearances.......................................................................10

Clearances to combustibles...........................................................................10

Clearances to Combustible trim.....................................................................10

Interior Wall Materials..................................................................................... 11

Trim Facings.................................................................................................................... 11

Adjoining Room Walls .................................................................................... 11

Air for Combustion & Ventilation............................................................. 11 - 12

Providing Adequate Ventilation ...................................................................... 11

Unusually Tight Construction ......................................................................... 11

Unconned Space..........................................................................................12

Determining Total Air Volume .........................................................................12

Important Pre-Installation Information ...........................................................13

Overview..............................................................................................................13

Additional Materials Required ........................................................................13

Leveling and Aligning Components................................................................13

Field Assembly Procedures............................................................................13

Firebox Assembly Procedures.................................................................14 - 16

Raised and Flush Hearth Application..................................................................16

Other Installations.....................................................................................16 - 17

Gas Piping Installation.........................................................................................16

Electrical Line Feed.............................................................................................16

Firebrick Liner Installation ...................................................................................17

Modular Firebrick Liner........................................................................................17

Initial Fireplace Operation ...............................................................................17

Appendix I ........................................................................................................18

Appendix II .......................................................................................................19

Appendix III ......................................................................................................20

Limited Lifetime Warranty ...............................................................................23

Installer/Customer/Unit Information ............................................................... 24

FOR USE WITH LISTED ANSI Z21.11.2 UNVENTED DECORATIVE ROOM

HEATERS NOT TO EXCEED 40,000 BTU/HR (11.723W) CONSULT WITH

INSTRUCTIONS FOR THIS FIREBOX FOR FURTHER INFORMATION.

Refer to installation instructions and check local codes prior to installing. This appliance

must be installed in accordance with local codes if any, if not, in accordance with the

National Fuel Gas Code ANSI Z223.1 installation codes.

MFP586-NS_05/2022

ANSI Z21.91 Ventless Firebox Enclosures for Gas-Fired Unvented Decorated Room Heaters.

16” - 22” : MAX. PROJ.

22” & ABOVE: 10” MAX. PROJ.

0” - 10” : NO PROJECTIONS

10” - 16” : 1-1/2” MAX. PROJ.

DISTANCE FROM SIDE OPENINGS

3” MIN. : 1-3/4” MAX. PROJ.

MANTEL CLEARANCES

6391 Jurupa Ave., Riverside, CA 92504

THIS APPLIANCE NEEDS FRESH AIR FOR SAFE OPERATION

AND MUST BE INSTALLED SO THERE ARE PROVISIONS

FOR ADEQUATE COMBUSTION AND VENTILATION AIR.

DO NOT REMOVE THIS LABEL

SERIAL No.

LABC & LARC Compliant

MODEL No.:

MFP44VF MFP49VFMFP39VF

DATE OF MFG:

BOTTOM 0”

0”

42”

18-¹/2”

TOP/

BACK/

SIDES

OPENING

TO CEILING

CLEARANCES TO COMBUSTIBLES

RECESS

DEPTH

Tested & Listed By

Report No.

08-154

ICC Evaluation Services

Report No. 2401

EXAMPLE ONLY

mason-lite.com 3

WARNING

Failure to position the parts in accordance

with these diagrams or failure to use only parts

specically approved with this appliance may

result in property damage or personal injury.

Fireplace Parts DiagramFireplace Parts Diagram

Figure 1: Exploded Diagram

CUSTOMER SERVICE & PARTS REPLACEMENT

Parts and accessories may be purchased from your

local dealer. Additional information is available from

Masonry Fireplace Industries,Inc. Accessory orders

will be accepted by mail, or you may call your order in

at: (800)-345-7078.

ITEM P/N DESCRIPTION QTY

MFP39-1

MFP44-1

MFP49-1

HEARTH (Left or Right) 2

MFP39-2

MFP44-2

MFP49-2

REAR WALL 4

MFP39-3

MFP44-3

MFP49-3

SIDE WALL 8

MFP39-5

MFP44-5

MFP49-5

DOME REAR - LOWER 1

MFP39-6

MFP44-6

MFP49-6

LINTEL 1

MFP39-6A

MFP44-6A

MFP49-6A

LINTEL FRONT 1

MFP39-6B

MFP44-6B

MFP49-6B

T-BAR 1

MFP39-7

MFP44-7

MFP49-7

DOME SIDE - LOWER 2

MFP39-9

MFP44-9

MFP49-9

DOME TOP 1

11 MFP170 RATING PLATE 1

12 #3 REBAR (Ø3/8”) 

MFP(39,44,49)SHBL- Herringbone

MFP(39,44,49)FRBL- Running Bond

Refractory Firebrick Liners

(Herringbone Pattern shown, also available in Running Bond -

see Page 17)

 QTY of rebar:

MFP39/44/49VF:

Eight (8) pieces 3/8” rebar x 34” long (included with unit)

Eight (8) pieces 3/8” rebar x 12” long (Not included)

mason-lite.com

Introduction

We extend a warm welcome from all of us at Masonry

Fireplace Industries, LLC. (MFI), proud manufacturers of

Mason-Lite Fireplaces.

Thank you for Choosing MFI.

You may have thought long and hard before you chose the

replace which would grace your home. Rest assured that

every component of the Fireplace has been tested to ensure

long-term durability.

Before Beginning the Installation

Read these instructions carefully before beginning the

installation of this Vent-Free replace. Also read the gas

log appliance manufacturer’s literature regarding sizing

and suitability for installation into this Enclosure prior to

installation.

Statement of Intended Use:

The Mason-Lite Vent-Free Universal Masonry Fireplace is a

modular refractory masonry unit designed for eld assembly.

The rebox is constructed using pre-cast, interlocking

refractory blocks. The blocks are then secured to each other

using high temperature mortar. The system includes all parts

necessary for the assembly of a complete masonry vent-free

decorative gas log enclosure.

In addition to the basic enclosure, a standard 1-1/8” thick,

high temperature refractory brick is required to line the

interior of the rebox.

These replaces are not intended to serve as a primary

heat source, rather, the replace was expressly created as a

supplemental source of heat.

The MASON-LITE is Designed for Use Only with any Vent

free decorative gas log sets meeting standard ANSI Z21.11.2

Vent free decorative gas log sets meeting standard ANSI

Z21.11.2, are supplied by others and are limited to any listed

vent-free gas-red log sets with heat input ratings up to

40,000 Btu/hr.

WARNING

Any application other than the “Intended

Use” as stated above is in violation of the

manufacturer’s instructions and is hereby

prohibited. Such violation may cause

immediate hazard, property damage or

loss of life and will void all liabilities to the

manufacturer and will void all warranties

explicit or implied.

GENERAL INFORMATION

*32"

*38"

*45 3/4"

4 1/2"

43"

39"

28 1/2"

28"

23"

SECTION A-A

Figure 2

ALL DIMENSIONS ARE IN INCHES.

* VERTICAL DIMS. ARE DRY STACK MIN., HIGH

TEMPERATURE MORTAR THICKNESS MAY ADD A

TOTAL OF 1 INCH TO OVERALL HEIGHT.

MODEL

MFP39VF

MFP44VF

MFP49VF

43”

48”

53”

39”

44”

49”

29-1/4”

34-1/4”

39-1/4”

Product Overview

Mason-Lite replaces are designed as Factory Built - Field

Assembled Fireplaces to be installed on both combustible and

non-combustible oor systems. They have been extensively

tested to perform with excellent results in this environment.

Attention: Be advised that all the illustrations in this manual

are for general reference only. They are not drawn to scale.

Actual design elements will vary from case to case. Pay

attention to specied minimum clearances as they relate to

combustible materials.

Firebox Dimensions:

mason-lite.com 5

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the u, with headaches,

dizziness, or nausea. If you have these signs, the replace

may not be working properly. Get fresh air at once! Have

the replace serviced.

Note: Some people are a󰀨ected more than others by carbon

monoxide. These may include pregnant women, people

with heart or lung disease, are anemic, anyone under the

inuence of alcohol, and those at high altitude.

General Safety Concerns

1. If you smell gas

l Shut o󰀨 gas supply.

l Do not try to light any appliance.

l Do not touch any electrical switch; do not use any

phone in your building.

l immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

l If you cannot reach your gas supplier, call the re

department.

2. This replace shall not be installed in a bedroom or

bathroom.

3. Never install the replace

l In a recreational vehicle.

l Where curtains, furniture, clothing, or other ammable

objects are less than 36 inches from the front, top, or

sides of the replace.

l In high tra󰀩c areas.

l In windy or drafty areas.

4. Do not use this replace as a wood-burning replace.

5. Do not add extra logs or ornaments such as pine cones,

vermiculite, or rock wool. Using these added items can

cause soot build-up.

WARNING

DO NOT USE OR STORE GASOLINE OR

OTHER FLAMMABLE LIQUIDS OR GASES IN

OR NEAR THE FIREPLACE!

SAFETY INFORMATION

DANGER

Carbon monoxide poisoning may lead to

death!

IMPORTANT

Read this owners manual carefully and

completely before trying to assemble,

operate, or service this replace. Improper

use of this replace can cause serious injury

or death from burns, re, explosion, electrical

shock, and carbon monoxide poisoning.

6. This replace is designed to be smokeless. If logs

appear to smoke, turn o󰀨 replace and call a qualied

service person.

7. Avoid any drafts that alter burner ame patterns. Do

not allow fans to blow directly into the replace. Do not

place a blower inside burn area of the rebox. Ceiling

fans may create drafts that alter burner ame patterns.

Soot build-up and improper burning will occur. Soot

build-up can settle on household surfaces outside the

replace.

8. This replace needs fresh air ventilation to run properly.

The Vent free decorative gas log set must have an

oxygen depletion sensor (ODS) pilot light safety system.

The ODS shuts down the replace if not enough fresh

air is available. See Air for Combustion and Ventilation,

page 10. If the replace keeps shutting o󰀨, see appliance

manufacturers’ troubleshooting instructions.

9. Do not run replace

l Where ammable liquids or vapors are used or stored.

l Under dusty conditions.

10. Do not use this replace to cook food or burn paper or

other objects.

11. Never place any objects in the replace or on logs.

12. Fireplace glass doors are not permitted in this decorative

room heater. Fireplace front becomes very hot when

running replace. Keep children and adults away from

hot surfaces to avoid burns or clothing ignition. The

replace will remain hot for a time after shut down. Allow

surfaces to cool before touching.

13. Carefully supervise young children when they are in the

room with the replace.

14. Do not use replace if any part has been exposed to

or under water. Immediately call a qualied service

technician to inspect the replace and to replace any

part of the control system and gas control which has

been under water.

15. Do not operate the replace if any log is broken. Do not

operate the replace if a log is chipped (dime-sized or

larger). Verify proper log placement prior to operating

appliance.

16. Turn replace o󰀨 and let cool before servicing. Only a

qualied service person should service and repair the

replace.

17. Operating the replace above elevations of 4,500 feet

may cause pilot outage.

Carbon Monoxide Poisoning

mason-lite.com

Installing Television (TV) Above Fireplace

Before installing a television (TV), be aware that this is a

heat producing replace. Objects placed above the unit are

exposed to elevated temperatures.

IMPORTANT NOTICE

TVs should not be used in situations where the actual

TV temperature exceeds the manufacturer’s technical

specication. Contact the TV manufacturer directly if

you cannot locate this information or have questions

regarding this information.

NOTE: The homeowner must understand that MFI

does not take responsibility for any negative impact

to televisions placed near this replace.

WARNING

Ensure clearances to combustibles are maintained

when building a mantel or shelves above the replace.

Elevated temperatures on the wall or in the air above

the replace can cause melting, discoloration or

damage to decorations, a television (TV) or other

electronic components.

SAFETY INFORMATION Continued

When choosing a location for your replace, avoid locations

that are subject to too much draft or locations where you

may encounter obstructions that may be in the way of the

replace once installed. Always check local codes and

familiarize yourself with the surrounding construction.

Carefully review the instructions supplied with the

decorative type unvented room heater for the minimum

rebox size requirement.

DO NOT INSTALL THE APPLIANCE IN THIS FIREBOX

UNLESS THIS FIREBOX MEETS THE MINIMUM

DIMENSIONS REQUIRED FOR THE INSTALLATION.

ATTENTION

A re or an explosion could occur causing

property damage, injury or loss of life if you

do not follow the information in this manual!

NOTE: THIS MANUAL MUST BE REPRODUCED ONLY

IN ITS ENTIRETY.

mason-lite.com 7

LOCATION

Note: You may need to provide combustion and ventilation

air from an outside source to adequately satisfy local codes

so avoid installing a combustion air inlet where the opening

could be blocked by snow, bushes or other obstacles. Note

that the access for outside air inlet is located on the right

hand side of the replace.

A ush installation is recommended where living space

is limited or at a premium. Check local codes for any

restrictions.

Projected installations can extend any distance into the

room. A projection may be ideal for a new addition on an

existing, nished wall.

Corner installations make use of space that may not

normally be used and provides a wider and more e󰀩cient

range for heat disbursement.

An internal wall installation provides a discreet option for

room separation and can also be ideal as an addition to an

existing wall.

Figure 4

*Height may vary. Maintain 1/2 inch clearance to

top of lintel (see Figure 12, page 10).

Model W H D

MFP39VF 43” *41” 28”

MFP44VF 48” *41” 28”

MFP49VF 53” *41” 28”

IMPORTANT

Vent-free heaters add moisture to the air.

Installing a replace in rooms without

enough ventilation air may cause mildew to

form from too much moisture.

IMPORTANT

Make sure the replace is level. If the replace

is not level, the log set will not work properly.

ATTENTION

You may need a building permit to install

a MASON-LITE fireplace. Check with the

local jurisdiction before you get started.

Figure 3

Internal

Wall

Installation Corner

Installation

Flush

Installation

Full

Projection

Installation

Seismic & Non-Seismic Code

Framing DimensionsTypical Installations

Mason-Lite Fireplaces have been tested and passed the

seismic requirements for Modular Masonry Fireplaces

throughout the entire United States. We understand that not

every installation needs the extra security that is involved

in a high seismic zones. Rebar is ONLY REQUIRED on

Mason-Lite units in seismic zones 3 & 4 shown in the map in

appendix III, page 20. We will supply rebar to all replaces

shipped to zones 3 and 4 in the United States unless

otherwise requested.

mason-lite.com

I-JOISTS

Example Only

Anchor

Brackets

I-Joist

Example Only

Simpson

Strong Tie

A-35 or

Equivalent

SUPPORTING FLOOR SYSTEM

Floor Framing

It is important to take into consideration that the load for the

Mason-Lite Fireplace is considerable, but, more important,

that it is a dead load that will have to be absorbed by a

relatively small amount of existing oor space.

It is the ultimate responsibility of the installer to ensure that

proper concrete slab supports are used.

WARNING

To the licensed design professional and/or

building contractor: It is your responsibility

to be certain that the Mason-Lite can be

properly supported by the combustible oor

system on which the replace will rest.

For replace support foundations installed on concrete

refer to Appendix I and II (pages 18 & 19) for specic

instructions.

Rebar locations

Lay-out the position of the replace and drill holes where the

rebar will be located. Secure the #3 rebar 4 inches into the

concrete foundation with ITW Epoxy or Simpson Epoxy. Follow

manufacturer’s instructions for installation of rebar into slab.

Wood Floor

Anchorage of replace to wood oor construction is required.

Refer to Figure 8, page 9 for anchorage dimensions. Four

anchors are required to attach to the sub-ooring framing.

Crawl Space or Upper Floor:

For installation of rebox over combustible crawl spaces or

upper oors, anchorage of the rebox is required. Illustrations

of examples of possible anchorage methods are shown in

Figures 5 thru 7 depending upon the type of oor framing.

Final method of anchorage is to be determined by licensed

design professional.

For conventional framing, where the oor joists are parallel

with the sides of the rebox, the addition of oor joists to

align with the anchor brackets allows the brackets to be

directly connected to the oor joists.

Note that additional oor joists may be required to support

the weight of the rebox and chimney. Where the oor joists

run parallel to the front of the rebox, anchorage can be

accomplished in like manner as shown in Figure 5 using

blocking between the oor joist.

For oors supported by I-Joists, the method of anchorage is

illustrated in Figures 6 and 7. Figure 10, page 9 illustrates

the general arrangement of anchorage to oor framing.

It is important to take into consideration that the load for

the Mason-Lite Fireplace must be considered as additional

dead load that will have to be supported by the oor

framing. Additional oor joists or I-joists may be required as

determined by the licensed design professional.

The dead weights for the replace are noted in Table I. It is

the task and responsibility of the general contractor/installer

to see that the proper reinforcement for weight loads are

made by a licensed design professional prior to the replace

installation.

As stated above, it is desirable to place additional framing

for alignment of anchor rods. Refer to Figure 10 for anchor

rod locations.

EXAMPLE ONLY

2X FLOOR JOIST

Figure 5

Floor Sheathing

not shown for

clarity

A35 Brackets

(16 required)

Figure 6

I-Joist Anchoring

Top View

Figure 7

I-Joist

Anchoring

Bottom

View

mason-lite.com 9

A4"

10"

WEIGHT DETERMINATIONS

The following are dead load weight estimates for the Mason-Lite Fireplace.

Other Weight Considerations:

Fireplace nished facing (surround): This information needs to be obtained from the contractor.

1 For wood structural members having a moisture content of less than 16 per cent at time of installation and used under

dry conditions, the deection resulting from L + 0.5D is permitted to be substituted for the deection resulting from L + D.

Note that MASON-LITE cannot accept responsibility for structural oor support details. All drawings are presented as mere

illustrations to indicate the presence of the underlying oor system. It is the responsibility of the general contractor/installer

to consult with a local licensed design professional for guidance in building a proper oor support system.

Table I

Fireplace Model MFP39VF MFP44VF MFP49VF

Fireplace Weight 809 lbs. 896 lbs. 987 lbs.

High temperature mortar,

Rebar & Ready Mix Concrete 350 lbs. 357 lbs. 364 lbs.

Firebrick Lining 333 lbs. 345 lbs. 356 lbs.

Floor Area 43” x 28” (8.12 ft²) 48” x 28” (9.33 ft²) 53” x 28” (10.30 ft²)

Table II - Deection Limits

Construction L S or W D +L1

Floor Members I/360 --- I/240

Model A

MFP39VF 38-3/4”

MFP44VF 43-3/4”

MFP49VF 48-3/4”

Figure 8 Figure 9

Typical Anchorage Layout

Figure 10

EXAMPLE ONLY

SECTION VIEW

ROTATED 90CW

10"

Fireplace

Outline

mason-lite.com

CLEARANCES

The Importance of Clearances

Warning to the structural engineer and/or building contractor:

It is your responsibility to be certain that the Mason-Lite can

be properly supported by the combustible oor system on

which the replace will rest. Be advised that this engineering

equation will be in addition to any live or dead weights that

the oor has to carry.

Clearances to Combustibles

Nothing is more important than paying strict attention to

giving clearance between replace surfaces and surrounding

“combustibles” the most common of which are:

lDrywall

lWood ooring

lPlywood sub-ooring

lFraming materials

lParticle board

lMill board

lPlywood paneling

Required Clearances are:

Unit front, sides, rear: 0"

Combustible Floor: 0"

Combustible Sheathing above opening top: 8" (203 mm)

Sheathing or trim to opening sides: 8" (203 mm)

Mantle above opening: 12" (305 mm)

Opening to sidewall: 24" (610 mm)

Insulation from rebox: 0"

The Mason-Lite Vent-Free replace may be installed at

“zero clearance” to plywood sheathing and to uninsulated

wood framing members at the unit bottom, sides, rear and

top when used for enclosing any listed vent-free gas-red

log set with maximum heat input ratings up to 40,000 Btu/

hr. However, when a Vent-Free replace is to be installed on

carpeting, wood ooring, or any combustible material other

than tile or concrete, the Vent-Free replace shall then be

installed on a metal or wood platform extending the full width

and depth of the Vent-Free replace.

Clearance to Combustible Trim:

Mason-Lite Vent-Free Fireplaces are designed to be custom

nished with facing trim and mantle to be an owner option.

However, all such trim material must meet standard replace

code requirements.

Non-combustible facing material must be applied to a

minimum of eight inches (8”) beyond the sides of the nished

opening of the Vent-Free replace and non-combustible

facing material must cover a minimum of twelve inches (12”)

above the nished opening of the installed unit.

Clearance to combustible trim are those distances required

to ensure that combustible mantle and facing material will

not be exposed to excessive heat while the unit is operating.

These clearances should be adequate to prevent

discoloration or warping of trim facings due to heat. However,

circumstances unique to each installation create variables

that may be beyond the scope of this manual. Therefore

be sure to follow gas log appliance manufacturer’s explicit

installation instructions regarding all minimum trim facing,

mantle height and side wall clearance requirements.

Parts of the combustible mantle assembly located above

and projecting more than one and one-half inches (1-1/2”)

inches from the rebox opening shall be kept at least twelve

inches (12”) from the top of the opening.

Mantle shelves with horizontal projection of ten inches (10”)

from the face of the replace must be held to a minimum

vertical distance of twenty inches (20”) from the top of the

nished replace opening.

Figure 11

Figure 12

Note: Mantle height clearances may vary among gas log

appliance manufacturers or with the use of rebox canopies.

Be sure to follow the gas log appliance manufacturer’s explicit

installation instructions for mantle height clearance requirements.

12"

NON-COMBUSTIBLE

ONLY ZONE

20" MIN

1 1/2"

10"

SAFE ZONE FOR

PROJECTION OF

COMBUSTIBLE

MATERIAL

TOP OF FIREPLACE OPENING

MANTEL

LINTEL FRONT

UNVENTED

FIREPLACE

DOME TOP

ALLOW 1/2" MIN

CLEARANCE

1-1/2”

8” MIN

NON-

COMBUSTIBLE

FACIA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Quemador de Mason-Lite

Mason-Lite

Mason-Lite OpalEscence LDB24L-EN Manual de usuario

Manuales populares de Quemador de otras marcas

Riello

Riello RS 28/M Guía de inicio rápido

True Induction

True Induction TI4B Manual de usuario

Weishaupt

Weishaupt WG20 Series Manual de usuario

Carolina Cooker

Carolina Cooker M116672 Manual de usuario

Riello

Riello RX 500 S/PV Manual de instrucciones

Unigas

Unigas HTP2000 Manual de usuario

baltur

baltur BT 250 DSG 4T Manual de usuario

muenkel design

muenkel design round burner Manual de usuario

Ecoflam

Ecoflam Multicalor 170.1 Manual de usuario

baltur

baltur BT 14 DSGW Manual de usuario

artisan

artisan Art-SB1 Guía

Riello

Riello P 140 T/G Guía de inicio rápido

AESYS

AESYS TurboFire II Manual de usuario

Riello

Riello RG1RKD Guía de inicio rápido

IKEA

IKEA GRILLSKÄR Manual de usuario

RUSTA

RUSTA SAREK Manual de usuario

PROPOINT

PROPOINT 8933657 Manual de usuario

baltur

baltur TBL 1000 ME Manual de referencia