Maschio GASPARDO CIRO E Manual de usuario

CIRO E/EW

EN - USE AND MAINTENANCE - OPERATOR'S MANUAL

Translation of the original instructions

MACHINES CODES:

EOM99041 - EOM99042

EOM99043 - EOM99044

MANUALE D’UTILIZZO DELLE MACCHINE ELETTRONICHE

MANUAL CODE: EOM0110OM^EN

EDIZIONE: 01/2019

ISTRUZIONI PER L’OPERATORE

Pagina 2

1. SERVICE DATA

The PTO speed is 540 rpm.

The supply voltage of the electronic system is 12 Vdc.

DANGER: This sign warns that the operations described cause serious lesions,

death or long term health risks, if they are not carried out correctly.

ATTENTION: This sign warns that the operations described could cause serious

lesions, death or long term health risks, if they are not carried out correctly.

CAUTION: This sign warns that the operations described could cause serious

damage to the machine, if they are not carried out correctly.

Carefully read all the instructions before operating the machine; if in doubt,

contact the dealer’s technicians. The manufacturer declines all

responsibility for the

in-observance of the safety and accident prevention rules described below.

2. SAFETY RULES

There are three levels of danger:

1. SERVICE DATA

2. SAFETY RULES

3. ELECTRONIC SYSTEM

4. PROCEDURE TO CALCULATE THE WEIGHT IN THE HOPPER

WHEN SPECIFIC WEIGHT IS GIVEN

5. SPREADING CHART FOR ELECTRONIC MACHINES

6. SPREADING OPERATION FOF ELECTRONIC MACHINES

7. TROUBLE SHOOTING CHART

INDEX

FOREWORD

Pag. 2

Pag. 3

Pag. 6

Pag. 8

Pag. 10

Pag. 11

Pay close attention to this danger sign anytime it appears

in this manual.

ISTRUZIONI PER L’OPERATORE

Pagina 3

3. ELECTRONIC SYSTEM

The electrical cables must be connected as shown below. In order to ensure

protection against water and correct operation, be sure to connect the connectors

correctly.

The system power connector (J4) must be connected to the appropriate socket on

the tractor. If it is not present, it is necessary to purchase, from the retailer or the

manufacturer, the appropriate wiring to be connected to the tractor battery, in order

to power the machine's electronic system. This wiring must be installed by qualified

personnel.

J4: power supply

J5: to this connector the coiled cable of the display

J6: connect here the cable to detect speed (or phonic wheel or ISO 11786 cable). If

you have ISO 11786 in the tractor, use the cable in the following picture.

Of this cable you plug the connector with the written "THEOR. SPEED" to J6.

Pay attention: "THEOR. SPEED" connector has a protection against dust and wa-

ter.Remove and plug it into the "TRUE SPEED" connector.

Connect cylindrical connector the display

J4 J6

ISTRUZIONI PER L’OPERATORE

Pagina 4

Home page.

Entrer the

Menù.

Enter in

advanced

settings

Enter in the

dedicated area

for the tractor’s

handling

Select the tractor on

which you want to use

this attachment. Then,

enter in the parameters’

modification page

Select the NMEA

option using lateral

buttons.

Then, exit the menu

GP antenna

Below it is illustrated the procedure for connecting and configuring the GPS antenna

(optional accessory). This component is used to detect the tractor's forward speed

and transmit it to the electronic system.

It is advisable to position the GPS antenna on the top of the tractor cabin, thanks to

the magnetic base, in order to obtain an optimal signal.

Follow the described steps to configure this attachment

Connect to J6

GPS Antenna Connect to

the display

ISTRUZIONI PER L’OPERATORE

Pagina 5

Home page.

Entrer the

Menù.

Enter in

advanced

settings

Enter in the

dedicated area

for the tractor’s

handling

Select the tractor on

which you want to use

this attachment. Then,

enter in the

parameters’

modification page

Select the GBSD

option using lateral

buttons.

Then, exit the menu

The electronically controlled machine can also be combined with a compatible

ISOBUS monitor for the management of prescription maps and automatic section

control. In order to get information regarding the cables to be used, the possibility

of connection and for the connection of the two devices, contact the manufacturer

or local retailer. Once you have purchased all the necessary cables and the soft-

ware license, follow the instructions below to enable the ISOBUS function.

ISTRUZIONI PER L’OPERATORE

Pagina 6

4. Procedure to Calculate the Weight in the Hopper When Specific Weight is Giv-

en (only for electronic machines without weighing system)

It is necessary to fill it with the maximum possible precision up to the “1000” reference

(that indicates the known volume of 1 litre) with the same fertilizer that will be used.

Afterwards the user shall weigh the filled in bottle by using a precision scale with at

least a 10-gram accuracy (see Fig. 14).

From the measured value it shall be deducted the tare of the bottle indicated on the

label on the bottle itself, and the result will be the specific weight of the product in use.

After loading it is advisable to level the product in order to read the filling level thanks to

the adhesive measurement labels applied inside the hopper or the extensions if

mounted (see Fig. 13)

The adhesive measurement labels indicate the level in litres, so in order to know the

quantity of the product inside the hopper in kilos it is necessary to multiply the value in

litres visually observed in the hopper by the measured specific weight.

Example:

Reading the adhesive measurement labels 550 litres (see fig. 13)

Detected Specific Weight: : Gross Weight – Tare

1,278 – 0,04 = 1,238kg/dm3

Weight of the product inside the hopper: 550 x 1,238 = 681 kg

This procedure determines the weight value to be entered on the machine monitor.

During the spreading it will be possible to check if the weight of material in the hopper is

correct. To do this is important to use the graduated scales into the hopper. Read the

value of the liters in the hopper by leveling the fertilizer and use the specific weight to

obtain the kg. If the weight value on the monitor and the kg obtained from the

calculation were different, the following procedure must be performed:

Do theoretical work for 1 Ha. Stop the tractor when 1 Ha is treated on the display.

Data to read from display:

- kg at the start of theoretical work (at the beginning)

- kg at the end of theoretical work (at 1 ha worked)

Data to read from hopper:

- liters at the start of work (at the beginning)

- liters at the end of work (at 1 ha worked)

ISTRUZIONI PER L’OPERATORE

Pagina 7

Fig. 13 Fig. 14

Compute the correction factor:

(starting theoretical weight - ending theoretical weight) = theoretical spread weight

Calculation of effective kg spread by means of the graduated scale in the hopper:

(starting real volume - ending real volume) * Specific weight = real spread weight

Make the following calculation:

Theoretical spread weight = correction factor

Real spread weight

Digit the result into the display to apply the correction (The result to be modified is

indicated at pag. 34 of the Display user manual at the Flow factor point). The flow

factor is applied to the fertilizer table used for the job.

The flow factor calculation can also be performed using the smartphone APP,

"Eurospand", which can be downloaded from the AppStore or Google Play. There, you

can find a section dedicated to electronically controlled machines. Then choose the

machine you are using and enter the "flow factor" page. In this page it is sufficient to

enter the value of the specific weight, obtained as described above, the Kg of product

loaded at the beginning of the work, the Kg spread on the monitor and the liters present

in the hopper after working for a certain surface. After entering all these values, by

pressing the "calculate" button, the value of the flow factor to be inserted on the monitor

will be directly provided, as shown in the images below.

ISTRUZIONI PER L’OPERATORE

Pagina 8

When starting a job, you need to select on the monitor a fertilizer that is the equal or

similar to the one you are going to use. Inside the machine monitor, there is a list of

fertilizers, each of which is connected to a flow curve.

Each curve has been detected by means of appropriate practical tests.

The tests were carried out at 540 rpm with horizontal spreading discs and at a

height from the ground of 80-90 cm.

The data are to be considered as indicative as many factors can influence the

quantity supplied, such as for example: the different physical characteristics of the

fertilizer, purchased in different periods or from different suppliers or used during

periods with different weather conditions.

Please note that the manufacturer is not liable and it is not required to pay any

compensation for a failed or insufficient harvest caused by spreading defects.

In the case of a machine without a weighing system, if the product to be used is not

present on the monitor, you can choose a product with similar features and

subsequently correct the flow factor as illustrated above.

The fertilizer choice can be carry out by using the smartphone APP, going to the

"product" section of the electronically managed machines. In this section, next to

the name of the fertilizer / seed, there is an information button, with which it is

possible to display the relative technical data, in order to find one similar to that

used by the customer and then select it on the monitor (help with table below).

In the case of a machine with a weighing system, it is sufficient to select on the

machine monitor a product similar to the one being used and the electronic system

will carry out the correction to distribute the exact amount Kg / ha set by the user.

Furthermore it is possible, both on a machine with a weighing system and without,

to add a new product. For this operation, see the user manual of the machine and

the user manual of the monitor.

5. Spreading Charts for electronic machines

Repeat the previous procedure if it is necessary during the job. For the

computation it is easier to use integer values for worked hectare.

In case of reuse in the future of that fertilizer table, the correction applied

remains stored in memory for that table. Check that this Flow factor is

good for the actual job, because the fertilizer spreading depends on the

weather. If it is necessary repeat the computation of the correction factor.

ATTENTION

ISTRUZIONI PER L’OPERATORE

Pagina 9

Since it is not possible to insert the entire name of the products inside the monitor,

the abbreviated name and the complete name are given below.

FERTILIZER NAME NAME ON THE MONITOR

Calcium Carbonate Calc Carb

Potassium chloride 60% Cloru Pot

Entec 13-10-20 Entec 13

Entec 14-7-17 Entec 14

Entec 25-15 Entec 25

Entec 26 Entec 26

Diammonium phosphate 18.46 FosfBiAmm

Nitrophoska blu 12-12-17 NPK Blu

Nitrophoska perfect NPK Perf

Ammonium nitrate 27% granular NitrAmGra

Novammon 24-0-29 NvAm24029

Triple superphosphate 46% PerFoTr46

Ammonium sulphate 20.5% SolAm20,5

Sulfate potassic magnesian30+10 SolPotMag

Granular Urea 46% UreaGr46

Spherical Urea 46% UreaSfe46

Agroferl 6N pelleed PELLET 6N

NPK 5-10-20 Arpa spa NPK 51020

Oat Avena- Oat

Azoferl 30 Azofert30

Ammonium nitrate NAC 27 N NAC 27N

Urea 46N Gran Concime Urea 46N

Flexammon 32-0-18 Flex32018

Wheat Grano- Whe

Mulgro NPK 17-9-16 NPK 17916

Rye grass seeds Logl- Ryag

Mesurol Pro An-slug Mesurol p

Nitrophoska gold NPK Gold

Barley Orzo- Barl

Rhizovit Humism 1 RhizHumis

Sulfammo 26 Sulfam26M

Basic Ferlenne 28 FERTIL 28

NPK 15-15-15 NPK151515

Yarabela Extran 26 (calcareous ammonium Nitrate 26) EXTRAN 26

Yaraliva Tropicote (Calcium nitrate) Tropicote

zanandrea semen riviera queen (Alfalfa) RIVIERA Q

ISTRUZIONI PER L’OPERATORE

Pagina 10

6. Spreading Operation

Take notice: Pay close attention to the fertilizer producer’s instructions, safety and

technical sheets. Improper use of fertilizers can cause serious damage to people,

animals, crops, soil and can cause water pollution.

• After choosing the spreading width (passage), tractor speed, type of fertilizer,

quantity to spread, the electronic system opens correctly the shutters.

Do not unscrew the fastening knob (particolare 1), and do not remove the

mechanical lock (particolare 2), Penalty, the linear actuator failure. See

picture 23.

Only authorized personnel can operates to this lock (fig. 23). Il suo utilizzo

è esclusivo per la manutenzione o la verifica del sistema elettronico di

apertura saracinesche.

Fig. 23

Do not unscrew the tie-rods on the spreader, because otherwise

mechanical and electronic calibrations change. Only authorized personnel

with appropriate tools can operate on the spreader.

CAUTION

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Maquinaria agrícola de Maschio

Maschio

Maschio GASPARDO PINOCCHIO 130 Guía del usuario

Maschio

Maschio F07011399 Guía del usuario

Maschio

Maschio TERMINATOR Guía del usuario

Maschio

Maschio TOSCA Series Guía del usuario

Maschio

Maschio Unico Guía del usuario

Maschio

Maschio PITAGORA INLINE Manual de usuario

Maschio

Maschio EXTREME 266 Series Guía del usuario

Maschio

Maschio PANTERA Series Guía del usuario

Maschio

Maschio GASPARDO COMPAGNA 1500 Guía del usuario

Maschio

Maschio PANTERA Guía

Maschio

Maschio HIPPO Guía

Maschio

Maschio GIRAFFONA F07010484 Guía

Maschio

Maschio ATTILA 250 Guía del usuario

Maschio

Maschio GIRAFFA 160 Guía

Maschio

Maschio BA series Guía

Maschio

Maschio RHINO Guía

Maschio

Maschio COBRA 00553051 Guía

Maschio

Maschio GASPARDO VELOCE Guía del usuario

Maschio

Maschio JULIA Guía del usuario

Maschio

Maschio JUMBO RAPIDO Series Guía del usuario

Maschio

Maschio GASPARDO AIRONE Guía del usuario

Maschio

Maschio ENTRY 120 Guía del usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario