Mas-Hamilton XX-07 Manual de usuario

OPERAOPERA

OPERATINGTING

TINGTING

TING

INSTRUCTIONSINSTRUCTIONS

INSTRUCTIONS

FOR THEFOR THE

FOR THE

X-07/CEX-07/CEX

-07/CEX-07/CEX

-07/CEX-07-07

-07-07

-07

HIGH SECURITYHIGH SECURITY

HIGH SECURITY

ELECTRONIC LOCKELECTRONIC LOCK

ELECTRONIC LOCK

(TYPE 1F)(TYPE 1F)

(TYPE 1F)

Please read all instructions carefully before putting your X-07/CEX-07 into operation.

TABLE OF CONTENTS

OPENINGTHE X-07 USINGTHE PRE-SET COMBINATION ............... 3

If You PassYour TargetNumberWhenDialing...............................5

RedialEntire CombinationIf............................................................6

SETTING OPERATING MODE AND NEW COMBINATIONS................7

Settingthe OperatingMode ............................................................7

AlternateMethod toSet Operating Mode ........................................9

Setting Combinations ................................................................... 10

Change aNew Combination Duringthe EntryProcess.................. 13

LockoutPrevention ....................................................................... 14

USINGTHE X-07 ................................................................................ 15

SingleCombinationMode ............................................................. 15

DualCombinationMode................................................................ 16

Supervisory/SubordinateMode...................................................... 17

UnlockinSupervisory/SubordinateMode ...................................... 17

LockUp inSupervisory/Subordinate Mode .................................... 18

If You Pass Your Target Number WhenDialing.............................. 20

USINGTHE AUDIT FEATURES OFYOUR X-07 ................................. 21

Check the Numberof Successful Openings .................................. 21

Check Unsuccessful Attempts Count ........................................... 22

GUIDETO SYMBOLS ........................................................................ 23

CEFUNCTION.................................................................................... 24

NormalOperation.......................................................................... 24

CombinationChange..................................................................... 24

CovertEntry.................................................................................. 24

ResettingCovert EntryandCovert EntryCombination Change ...... 25

RecoveringIf theCovertEntry CombinationIsForgotten ............... 25

GUIDETO SYMBOLS - CE FUNCTION.............................................. 26

For 24-hourTechnical Support Call:

1-800-950-4744 or (859) 253-4744

OPENINGTHEX-07OPENINGTHEX-07

OPENINGTHEX-07

USING THE PREUSING THE PRE

USING THE PRE--

-SET COMBINASET COMBINA

SET COMBINASET COMBINA

SET COMBINATIONTION

TIONTION

TION

Your X-07 lock has been shipped pre-set in the Single Combination Mode with the

combination set to 50-25-50.

Practice opening the lock several times before you set a new combination.

Your X-07 uses sophisticated computer security and makes dialing much easier than

that of traditional combination locks.

The X-07’s computer recognizes a number as being part of a combination when you

stop dialing on that number and then reverse dialing directions. This enters the num-

ber into the computer memory.

If at any time the dial remains stationary for more than 40 seconds, the computer will

reset (LCD will go blank) requiring the operator to redial the entire combination.

Important: The X-07 has protective software that detects robotic dialing. If robotic

dialing is detected, the X-07 will not open even if the correct combination has been

dialed.

Theusershould dial withcompletefull wrist turns.Stopping to regripproducespauses

in dialing activity. This helps the X-07 distinguish between human and robotic dialers.

The X-07 may mistake a human for a robot if the user:

1. Dials more than 1.3 revolutions in either direction with no pauses in dialing

activity;

2. Dials with very short, quick repetitive turns, producing very short pauses in

dialing activity;

3. Dials a combination in less than 15 seconds.

TO OPEN THE X-07:TO OPEN THE X-07:

TO OPEN THE X-07:

1. Dialleft (counterclockwise) 4-6turns to “powerup” the lock.Numbers will appear

on the LCD display screen.

OPENING THE XOPENING THE X

OPENING THE X-07-07

-07-07

-07

OPENING THE XOPENING THE X

OPENING THE X-07-07

-07-07

-07

2. Continuedialing leftto thefirstnumberinthe combination(50). Stop.The number

50 will be displayed on the screen.

3. Now dial in the opposite direction (right, clockwise) to 25. Stop.

4. Now dial left to 50. Stop.

5. Now dial right. After OP (OPen right) appears on the display screen, continue

dialing to the right to pull the lock bolt.

IF YIF Y

IF YOU POU P

OU POU P

OU PASS YASS Y

ASS YASS Y

ASS YOUR TOUR T

OUR TOUR T

OUR TARGET NUMBER WHEN DIALINGARGET NUMBER WHEN DIALING

ARGET NUMBER WHEN DIALINGARGET NUMBER WHEN DIALING

ARGET NUMBER WHEN DIALING

A. Example: target number-25.

If you pass your target number by 4 or more (photo 1), continue dialing in the

same direction (photo 2), until you reach the target number again (photo 3).

B. Example: target number-25.

If you pass the target number by no more than 3 numbers (photo 1), you may

reverse directions slowly (photo 2) and the display will “jump back” 4 numbers

(photo 3).

Now you may dial slowly in the original direction to the target number (photo 4).

REDIAL ENTIRE COMBINAREDIAL ENTIRE COMBINA

REDIAL ENTIRE COMBINATION IF ...TION IF ...

TION IF ...TION IF ...

TION IF ...

A. The Lightning Bolt symbol is displayed.

B. The screen goes blank before the lock bolt is withdrawn.

When you feel comfortable opening the X-07 using the pre-set combination, you are

ready to put the lock into operation.

SETTING OPERASETTING OPERA

SETTING OPERATING MODE AND NEW COMBINATING MODE AND NEW COMBINA

TING MODE AND NEW COMBINATING MODE AND NEW COMBINA

TING MODE AND NEW COMBINATIONSTIONS

TIONSTIONS

TIONS

SETTING OPERASETTING OPERA

SETTING OPERATING MODE ANDTING MODE AND

TING MODE ANDTING MODE AND

TING MODE AND

NEWCOMBINANEWCOMBINA

NEWCOMBINATIONSTIONS

TIONSTIONS

TIONS

Before you can set a new combination, you must select and set a mode of operation.

The X-07 has three modes of operation.

Single Combination Mode: TheX-07will open when onethree-numbercombination

is successfully dialed.

Dual Combination Mode: Two separate combinations are required to open the X-

07. Either combination may be dialed first, however the operator must begin entering

the second combination within 40 seconds of entering the first combination.

Supervisory/Subordinate Mode or Super/Sub Mode: Two separate combinations

are required to open the lock, with the Supervisory Combination controlling access of

the Subordinate Combination. The Supervisory Combination must be entered first.

There can be unlimited delay between entering the Supervisory Combination and

entering the Subordinate Combination. There can also be unlimited openings by the

holder(s) of the Subordinate Combination until the Supervisory Combination is redi-

aled.

SETTING THE OPERASETTING THE OPERA

SETTING THE OPERATING MODETING MODE

TING MODETING MODE

TING MODE

Use the Change Key (photo 1) provided with your X-07 to set the desired operating

mode and combinations. If at any time during the process you see the Key and

Lightning Bolt symbols displayed (photo 2), stop the sequence and return to Step 3. If

at any time you see a Lightning Bolt symbol displayed (photo 3), stop and return to

Step 2.

1. Retract the bolt by entering the correct combination(s). In dual Combination or

Supervisory/Subordinate modes, you must enter both combinations.

(The first time use the pre-set combination: 50 left-25 right-50 left).

NOTE:

Release the bolt mechanism on the container so the dial will turn

freely. Different containers have different release mechanisms.

2. Insert the Change Key into the slot on the back of the lock.

3. Dial to the left (counterclockwise). The Change Key symbol will appear in the

display. The lock will never open when the Change Key symbol is displayed.

4. Enter the current combination or combinations again, example 50-25-50.

SETTING OPERASETTING OPERA

SETTING OPERATING MODE AND NEW COMBINATING MODE AND NEW COMBINA

TING MODE AND NEW COMBINATING MODE AND NEW COMBINA

TING MODE AND NEW COMBINATIONSTIONS

TIONSTIONS

TIONS

ALAL

ALTERNATERNA

TERNATERNA

TERNATE METHOD TO SET OPERATE METHOD TO SET OPERA

TE METHOD TO SET OPERATE METHOD TO SET OPERA

TE METHOD TO SET OPERATING MODETING MODE

TING MODETING MODE

TING MODE

This alternate method replaces steps 1-4. If you have lost or

forgottenthe currentcombinationandhaveaccess tothe back

of the lock, you can select a mode of operation to set new

combinations using the serial number found on the inside

cover of the lock.

This serial number will not open the lock; it

will only allow you to set new combination.

A. Dial an incorrect combination to obtain the Lightning Bolt error symbol.

B. Insert the Change Key into the back of the lock.

C. Enter the serial number as the current combination: (Example 000054)

Dial:

Left to the first 2 digits of the serial number. Stop 00. (photo 1)

Right to the second 2 digits of the serial number. Stop 00. (photo 2)

Left to the third 2 digits of the serial number. Stop 54. (photo 3)

Right SL (select mode will be displayed) continue with Step 5. (photo 4)

5. Dialing right, the symbol SL (for Select Mode) will be displayed (photo 1). Now

dial left to select the mode of operation:

1 —for Single Combination Mode (photo 2)

2 —for Dual Combination Mode (photo 3)

3 —for Supervisory/Subordinate Mode (photo 4)

6. Stop on the number of your selection. Now dial right to set the mode. The

symbol EC or El will be displayed depending upon the mode selected.

SETTING COMBINASETTING COMBINA

SETTING COMBINATIONSTIONS

TIONSTIONS

TIONS

7a. If selection 1; Single Combination Mode was chosen:

(1) The symbol EC (for Enter Combination) will appear on the display (photo 1).

Enter the desired combination by dialing the numbers in correct sequence:

(Example 30-60-90)

Dial:

Left (counterclockwise) to the first number. Stop. (photo 2)

Right (clockwise) to the second number. Stop. (photo 3)

Left (counterclockwise) to the third number. Stop. (photo 4)

Right (clockwise) until display flashes the new combination. (photo 5)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerrar de Mas-Hamilton

Mas-Hamilton

Mas-Hamilton X-08 1F Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario