Martin Magnum 800 Manual de usuario

USER GUIDE

Version 1.0

CONTENTS

INTRODUCTION ......................................................................................................................... 3

SAFETY....................................................................................................................................... 3

INSTALLING THE FLUID BOTTLE............................................................................................. 4

CONNECTING TO THE POWER SUPPLY ................................................................................ 4

OPERATING THE REMOTE....................................................................................................... 5

MAINTENANCE .......................................................................................................................... 5

TROUBLESHOOTING GUIDE.................................................................................................... 6

TECHNICAL SPECIFICATION ................................................................................................... 7

For optimum performance and safety, please read this manual thoroughly.

Note:

without permission in writing from Martin Professional A/S, Denmark.

INTRODUCTION

The MAGNUM 800 is a compact and efficient fog generator for semi-professional use. It

utilises a water-based fluid with an aluminium and copper heat exchanger to create a white fog

for entertainment and theatrical use. Quality materials and innovative design combine to give

ease of use and long service life.

FEATURES:

•1 litre fluid container

•Remote control with timer and output controls

•5 metre remote cable

•750 W heating element

•Copper and aluminium heat exchanger

•'Pump Ramping' feature to maximise run time

•Compact, only 170 x 422 x 160 mm

•Light weight, only 5 kg

•Power ON/OFF switch

•IEC power inlet

•Efficient insulation

•Fail-safe over-temperature cut-out (manual reset)

SAFETY

•Read this manual thoroughly before operating the machine.

•Never install fog machines over people's heads.

•Do not restrict the ventilation on the machine.

•Operating the machine in areas with poor ventilation may lead to condensation forming on

surfaces and floors - THIS CAN BE DANGEROUS.

•Do not point the machine into people's faces when making fog.

•Never remove the cover without first disconnecting the machine from the power supply.

•Keep the output of the machine at least 60 cm (2 feet) away from people and surfaces.

•The output nozzle at the front of the machine is very hot and must not be touched.

•Observe the warnings printed on the machine.

•Do not use the machine if it is in poor or unsafe condition, e.g., if the supply cord is

damaged.

•Always use genuine JEM / MARTIN fluid in the machine, other fluids may be dangerous.

•Refer all service to qualified service personnel.

INSTALLING THE FLUID BOTTLE

Always disconnect the machine from the power supply when working with the fluid

system.

1. Fit the bottle of JEM / MARTIN fluid into the fluid compartment and fit the cap with fluid

pipe.

2. Do not attempt to fill the bottle whilst in the machine.

3. If the machine has not been used recently it may be necessary to operate the pump for 10

- 15 seconds to prime the pump. Do this by setting the fog level on the remote to maximum

and pressing the fog button when the machine is at operating temperature.

Avoid running the pump for long periods without fluid, as this can cause damage to the seals.

CONNECTING TO THE POWER SUPPLY

Check the rating plate on the machine to see that the rated voltage and frequency match the

local supply.

This machine must be earthed!

The wires in the standard cord are coloured as follows:-

Green/Yellow Earth connection

Blue Neutral connection

Brown Live (phase) connection

1. Fit the cord to the IEC connector on the machine and the power supply connector.

2. Before switching the machine on, set controls on the remote to the off positions. See the

section on the remote control for instructions. The remote must be connected for the

machine to start heating.

3. Set the power switch to ‘1’ and the Heating LED on the remote will light up. The machine

will take approximately 10 minutes to reach operating temperature, at which point the

Ready LED will light up.

4. The machine will now make fog when operated from the remote.

OPERATING THE REMOTE

MAINTENANCE

The MAGNUM 800 is designed and constructed to give a long and trouble-free service

life.

However, like all equipment, it will benefit from regular simple maintenance.

Keep the following points in mind:

•If fluid is spilt onto the casework of the machine it should be cleaned with a damp cloth

(disconnect the power supply before doing this).

•Do not use solvents to clean the casework of the machine as this may remove the silk

screen printing.

•Only use JEM / MARTIN fluid in the machine. Other fluids may cause damage to the heat

exchanger and other components.

•Keep the cables in good condition.

Timer Control and LED

The timer is switched on by rotating the Timer control

clockwise until the green Timer LED is on. At this point the

repetition rate of the timed pulse is minimum. Rotating the

control clockwise causes the repetition rate to increase. The

duration of the pulse is fixed, only the frequency can be

changed. When combined with the output level control this

provides a simple way to maintain a constant level of fog.

Fog Switch

Press the fog switch at any time (the Ready LED must be on)

to get fog output at the level currently set with the level control.

Ready LED (Green)

When the machine is up to operating temperature and capable

of producing fog, the Ready LED is on.

Heat LED (Red)

The Heat LED is on when power is being supplied to the heat

exchanger. When the maximum operating temperature is

reached the LED is off.

Output Level Control

The output level is rotated clockwise to increase the fog output

level. Remember that the machine has ‘Pump Ramping’ so that

the output level will automatically reduce as the heat

exchanger cools, thus allowing longer run times.

TROUBLESHOOTING GUIDE

All checks marked * must be carried out with the power supply disconnected from the

machine.

The inside of the machine contains parts at high temperature, always allow the machine

to cool before removing the cover.

Symptom Probable Cause Remedy

No LEDs come on when

power is applied to the

machine

•Remote control not

connected

Connect remote to the DIN socket on

the top of the machine

•Main power switch is

off

Switch on

•Main internal fuse

open circuit

*Remove the cover and locate the

fuse on the PCB. Replace the fuse

with one of correct rating. (See Tech.

Spec)

•Temperature sensor

open circuit

*Make a continuity check on the

sensor

The machine never

reaches operating

temperature (ready LED

never comes on)

•An electronic or other

failure has occurred

in the heating system

Refer the problem to a service agent

•The remote control or

its connections are

faulty

Replace the remote control

No smoke is produced

when the Fog button is

pressed

•No fluid in the bottle Replace the bottle

•The pump system is

not primed with fluid

Set the output level control to

maximum and hold down the Fog

button for 15 seconds

•The output control is

not set high enough

Increase the output level setting

•An electronic failure

has occurred

Refer the problem to a service agent

Never replace the internal fuse with one of a higher rating. If the fuse blows when

replaced, it means that there is a serious problem with the machine that should be

referred to a service agent.

Never operate the machine with the safety over-temperature trip disabled. If the trip

operates it means that the electronic control system has malfunctioned.

TECHNICAL SPECIFICATION

Heat Exchanger

•Input power UK/Europe 750W @ 240V, 50Hz

USA 750W @ 120V, 60Hz

•Construction Copper vaporising coil in cast aluminium with integral

heater

•Operating temperature 300°C maximum

•Over-temperature protection Direct contact thermal cut-out with manual reset

Fuse

•240V (UK/Europe) 5 A time-delay (T) 5 mm x 20 mm

•120V (USA) 10 A time-delay (T) 5 mm x 20 mm

Pump

•Input power UK/Europe 40W @ 240V, 50Hz

USA 40W @ 120V, 60Hz

•Type High pressure piston pump

Control System

•Type Electronic

•Temperature sensor Thermocouple

Operating Environment

•Ambient temperature range 0°to +40°C

•Relative humidity 70% maximum

Dimensions

•Height x Length x Width 170 mm (220 mm with bottle) x 422 mm x 160 mm

•Weight 5 kg (6 kg with 1 litre fluid bottle)

Note:

The maximum length of the remote control cable must not exceed 35m.

Martin Professional A/S,Olof Palmes Allé 18, DK-8200,Aarhus N

Phone: +45 87 40 00 00 Internet: www.martin.dk

Tabla de contenidos

Otros manuales de Máquina de niebla de Martin

Martin

Martin Jem Hazer Pro Manual de usuario

Martin

Martin JEM Compact Hazer Pro Manual de usuario

Martin

Martin Magnum 2500Hz Manual de usuario

Martin

Martin Magnum 1200 Manual de usuario

Martin

Martin Magnum 1500 Manual de usuario

Martin

Martin JEM K1 Hazer Manual de usuario

Martin

Martin THRILL Manual de usuario

Martin

Martin Magnum 850 Manual de usuario

Martin

Martin Magnum Pro 2000 Manual de usuario

Martin

Martin Magnum Club Smoke System Manual de instrucciones

Martin

Martin Magnum Pro 2000 Manual de usuario

Martin

Martin JEM ZR44 Hi-MASS Manual de usuario

Martin

Martin Jem Hazer Pro Manual de usuario

Martin

Martin ZR44 Hi-Mass Manual de usuario

Martin

Martin Jem ZR25 Manual de usuario

Martin

Martin Magnum 650 Manual de usuario

Martin

Martin Magnum 2500Hz Manual de usuario

Martin

Martin Magnum 1200 Manual de usuario

Manuales populares de Máquina de niebla de otras marcas

Antari

Antari ICE Manual de usuario

Boost

Boost BOOST-FOG400LED-BK Manual de usuario

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manual de usuario

EuroLite

EuroLite ZEITGEIST FOG-1200 Manual de usuario

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manual de usuario

PROEL

PROEL DRAGO HEAVY PLFD150HY Manual de usuario

Sparklyn

Sparklyn Y846 Manual de usuario

Magicfx

Magicfx CO2 Gun Manual de usuario

Ibiza

Ibiza LSM500LAS Manual de usuario

Antari

Antari M-5 Manual de usuario

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manual de usuario

High End

High End F-100 Manual de usuario

Chauvet

Chauvet ARENA 2100 FLEX Manual de usuario

Antari

Antari X FAZER Manual de usuario

Beamz

Beamz F1600 Manual de usuario

Sagitter

Sagitter SG ARS900C Manual de usuario

KISANKRAFT

KISANKRAFT KK-STF-480 Manual de usuario

Orion

Orion OT-U250PP Guía