Martin Yale Count AccuCreaser Manual de usuario
Serial Number ___________________________
Date ___________________________________
ACCUCREASER TOUCH
Page left blank intentionally
2
3
TABLE OF CONTENTS
INTRODUCTION .......................................................................................................... 5
ELECTRICAL REQUIREMENTS AND SPECIFICATIONS ....................................................... 5
SAFETY PROCEDURES/CARE & MAINTENANCE .............................................................. 6
COMPONENT IDENTIFICATION .................................................................................... 7
SETTING UP ACCUCREASER.......................................................................................... 8
PAPER STOP ASSEMBLY ............................................................................................ 9
PERF MODE ............................................................................................................ 12
FEEDER MODE ........................................................................................................ 13
CREASE MODE ........................................................................................................ 13
PROGRAMMING FOR CREASE MODE ............................................................................ 15
HALF FOLD .............................................................................................................. 15
TRI-FOLD................................................................................................................. 15
Z FOLD .................................................................................................................... 15
LETTER FOLD ........................................................................................................... 15
ROLL FOLD .............................................................................................................. 15
GATE FOLD .............................................................................................................. 16
DOUBLE GATE.......................................................................................................... 16
DOUBLE PARALLEL ................................................................................................... 16
PERFECT BIND SINGLE HINGE ................................................................................... 17
CUSTOM CREASE SETUPS .......................................................................................... 17
SAVING/RECALLING CUSTOM JOBS ............................................................................ 18
PERFECT BIND DOUBLE HINGE ................................................................................. 16
PERFECT BIND NO HINGE ......................................................................................... 17
TRANSPORT AND VACUUM OPERATION CONTROLS...................................................... 14
DELIVERY TRAY ASSEMBLY....................................................................................... 8
MACHINE CONTROLS................................................................................................... 10
PUMP CONTROLS.........................................................................................................10
TOUCH SCREEN CONTROLLER......................................................................................11
4
SETTING THE AUTOMATIC FEEDER............................................................................. 20
HEIGHT ADJUSTMENT CALIPER .................................................................................. 20
LOADING THE FEEDER ............................................................................................... 21
CHECKING THE SENSOR ................................................................................................ 22
PERF SHAFT & STRIKE PLATE ......................................................................................22
REMOVING THE PERF SHAFT TO CHANGE CONFIGURATIONS .......................................23
PERFORATING AND SETTING PERF BLADE .................................................................24-25
FOLDING DIRECTION OF PAPER ................................................................................. 27
CHANGING LOWER CREASE DIE .................................................................................. 27
TROUBLESHOOTING ...................................................................................................... 28
ADJUSTING RAC ROLLERS
(DEPTH OF CREASE)
..........................................................27
4
MICRO ADJUSTING THE CREASE POSITION ................................................................ 18
BATCH COUNTER.........................................................................................................19
SCORING AND SETTING SCORE BLADE ...........................................................................26
ACCUCREASER…………………………………………….350 lbs
………………………………………………………………….32”Lx27”Wx26”D
………………………………………………………………….48”Lx48”Wx52”H
………………………………………………………………….5”x5-7/8”
.……………………………………………………….………..18”x20”
Net Weight:
Overall Dimensions:
Boxed Dimensions:
Min. Sheet Size:
Max. Sheet Size:
Power Requirement:
Circuit Protection:
110v, 60 HZ, AC, or International 230v, 50/60HZ, AC
20 amp line required for models with pump
3 AMP Circuit Breaker, 3 AMP Fuse
NOTE: The AccuCreaser is capable of handling many types of applications above and
beyond the standard specifications. It is possible to feed quite a variety of jobs, from
30” sheets to die cut stocks. However, the performance of the AccuCreaser on these
special applications is directly related to the experience of the operator.
MODE 8.5 X 11 Sheet (est)
12,000Perf Mode:
Crease
Mode:
5,500
5
OPERATING SPEEDS
SPECIFICATIONS
ELECTRICAL REQUIREMENTS AND SPECIFICATIONS
•Read through the owner’s manual. Follow instructions CAREFULLY.
•NEVER use a wet area. Electric shock could occur.
•Use a GROUNDED outlet and a GROUNDED circuit. Do no use
ungrounded equipment on the same circuit.
•Always use a dedicated line. DO NOT use with line splitting surge
protector.
•Keep fingers and hands away from creasing bar, perf blades, and rubber
rollers.
•Keep cords clear of moving parts.
•Turn off machine at the top panel, then unplug the main power cord.
This will prevent damage to your machine by power/voltage spikes.
•To unplug cords, always grasp the plug body, never pull on cords to
disconnect. Wire fatigue and possible shock could result from improper
disconnect procedures.
BE ALERT! BE CAREFUL!
CARE AND MAINTENANCE
The ACCUCREASER is a precision machine. It is very important to keep it free of
excessive dust, dirt and foreign matter. We recommend that you keep the machine
covered when not in use.
BEARINGS/BUSHINGS:
The bearings are sealed roller bearings and are designed to
be self lubricating, however dirt and dust can get into them causing clogging and dirt
build up. It is recommended to oil them daily under heavy use or monthly under light
use. The Bushings are Bronze and require lubrication more frequently. Oil these once
a week under heavy use.
STRIKE DIE:
The groove in the lower die should be cleaned periodically using a
toothbrush to remove any dirt or build up.
SENSOR EYE:
Clean the lower reflector tape located on the plate under the strike
plate of the machine. Dust will cause the beam to not reflect correctly. Clean when
necessary.
REMOVEABLE SCREWS:
When these show signs of wear or stripping, replace as
soon as possible. If these strip or hollow out they can be costly to remove. If you do
keep your AccuCreaser clean and in top condition, it will give you years of service.
6
SAFETY PROCEDURES
BEFORE USE:
DURING USE:
AFTER USE:
Crease Bar
Delivery Tray
Perf and Score Assemblies
Power Switch
Pump with
Vacuum Valve
Pg. 11
Pg. 8
Pg. 10
Pg. 24-26
Touch Screen
Delivery Tray
Pump with Vacuum
Valve Perf and Score
REFERENCES
COMPONENT IDENTIFICATION
7
Touch Screen
Paper Stop
Install on top of the first
dowel pin and under the
second.
Tuck Lip up as shown
SETTING UP YOUR ACCUCREASER
This machine is 99% ready to go when it arrives on your dock. There are only a few
items that need to be put into position before it is ready to use. Those 2 items are
below:
DELIVERY TRAY ASSEMBLY
INSTALLING THE DELIVERY TRAY
Position the tray to slide it under the dowel pins and rest it on the lower dowel pins.
Upper Position shown below
8
Now that the Machine is setup, let's learn how to use the machine. The
sections below will guide you through the operation of the machine.
PAPER STOP ASSEMBLIES
INSTALLING THE PAPER STOPS
1. Inside the box should be 3 paper stops (2 will have a bend & 1 will be straight).
2. Place the straight paper stop in place. This is the back paper stop. (See Diagram)
3. Place the 2 paper stops in position as show below.
The paper stops hold their position using knobs making it easier for adjustment. The
positions of the paper stops will depend on the individual job.
*HWWLQJWKHSRVLWLRQFRUUHFWLVLPSHUDWLYHWRVPRRWKRSHUDWLRQRIWKHPDFKLQH
If the paper stops are set too close the paper will hit them as it exits the machine
resulting in a paper jam. However, if the paper stops are set too loose the paper will
stack in an unorganized manner.
9
There is one switch on the Accucreaser the main power. Everything else is controlled
by the Touch Screen.
MAIN POWER
On the operator side cover at the top on the right side is the main power button . This
is the on and off power for the machine. When pressed it will illuminate. This is how
you know the machine is on. Do not leave the machine on when not in use.
The pump is controlled by the touch screen. Pressing the run button the pump is
powered on. Use the knobs on the pump (pictured below right) to control the output
of the pressure and vacuum. As illustrated on the knobs you can control the suction
and the blow affecting the stock. Use care to not remove the pump knobs completely
as they have a directional specific spring for each knob. Depending on the stock you
are using you will adjust these knobs to ensure proper feeding. The suction can be
adjusted as well as the vacuum pickup point to ensure enough suction to pull the
bottom sheet. The pressure will “fluff” the stack along the rails and make it easier to
pull the bottom sheet as well.
MACHINE CONTROLS
PUMP CONTROLS
10
Tabla de contenidos
Otros manuales de Máquina encuadernadora de Martin Yale
