Martin Audio C115 Manual de usuario
CONTENTS (ENGLISH) Page No
1 INTRODUCTION 2
2 UNPACKING 2
3 WALL-BRACKET INSTALLATION 3
4 ROTATION FEATURE 3
5 NEAR-CORNER MOUNTING 3
6 ATTACHING THE SPEAKER TO THE BRACKET 3
7 CONNECTING THE C115 4
8 TRANSFORMER VERSIONS 4
9 WARRANTY 4
10 TECHNICAL SPECIFICATIONS 5
11 FIXING TEMPLATE 6
Martin Audio – C115 Loudspeaker
MARTIN AUDIO
LONDON
The Martin Experience
All material © 2007. Martin Audio Ltd. Subject to change without notice.
1 INTRODUCTION
Thank you for purchasing a Martin Audio C115 loudspeaker. This is a
versatile surface-mount loudspeaker designed for high quality music and
speech reproduction in distributed sound systems. It has been carefully
styled to present a discrete, high quality appearance, which will blend
unobtrusively into commercial and architectural environments.
The C115 is available in the following electrical configurations:
• 8 ohm
• 100V line (Europe and Japan)
• 70V line (USA)
Typical applications include retail outlets, bars, hotels and restaurants.
Each C115 is supplied with a unique wall bracket which permits off-axis
adjustment of 40 degrees horizontally and 35 degrees vertically. Additional
hardware is available for corner mounting and for arrays of 2, 3 or 4
speakers to give the C115 exceptional mounting flexibility.
2 UNPACKING
The C115 is packed in pairs complete with wall brackets. Each Martin
C115 is built to the highest standard and thoroughly tested before it leaves
the factory. After unpacking the speakers and brackets, examine them
carefully for any signs of transit damage and inform your dealer if any such
damage is found.
Check that the electrical configuration supplied (8 ohm, 100V line or 70V
line) is the one you require. It is suggested that you retain the original
packaging so that the speakers can be repacked and returned if necessary.
Please note that Martin Audio and its distributors cannot accept
responsibility for damage to any returned product through the use of non-
approved packaging.
Martin Audio – C115 Loudspeaker
ENGLISH
2
This equipment conforms to the requirements of the
EMC Directive 89/336/EEC, amended by 92/31/EEC
and 93/68/EEC and the requirements of the Low
Voltage Directive 73/23/EEC, amended by 93/68/EEC.
Standards Applied EMC Emission EN55103-1:1996
Immunity EN55103-2:1996
Electrical Safety EN60065:1993
All material © 2007. Martin Audio Ltd. Subject to change without notice.
3 WALL-BRACKET INSTALLATION
The wall-bracket should be fixed to the wall prior to the installation of the
C115. The bracket has four elongated fixing holes with the fixing positions
shown by small arrowheads in the moulding. The bracket or fixing template
should be held up against the wall in the position required and the four
fixing positions marked on the wall (see template on the outside back
cover). A qualified person such as a building professional of qualified
engineer should determine the method of fixing and type of fixing screw
based on an evaluation of the wall construction.
4 ROTATION FEATURE
The fixing holes in the wall-bracket are elongated to allow the bracket to be
rotated 10 degrees clockwise or anti-clockwise before fully tightening the
fixing screws. This rotation feature may be used to restore horizontal
alignment if the C115 is to be used with a significant downward tilt.
5 NEAR-CORNER MOUNTING
The wall-bracket supplied can be used to mount the C115 close to a corner
if required rather than using the optional dedicated corner mount. Typical
distances of the centre of the bracket from the corner to allow for downward
tilt angles of 0, 10, and 20 degrees are shown below. Each tooth on the
egg shaped-moulding corresponds to a tilt angle of 10 degrees.
Tilt Tooth Distance of centre of
bracket from corner
0˚ 0 57mm
10˚ 1 67mm
20˚ 2 82mm
6 ATTACHING THE SPEAKER TO THE BRACKET
Once the bracket has been fitted to the wall, the speaker can be installed.
The speaker is fixed to the tongue of the wall-bracket by means of an M5
socket cap screw supplied with the bracket. The recess in the rear of the
C115 should be placed over the tongue and the M5 screw inserted upwards
through the hole in the base of the C115 between the connecting terminals
into a threaded insert in the tongue. The speaker can be rotated
horizontally on the tongue about the axis of the "base" screw which should
then be fully tightened when the required horizontal angle has been
determined.
The vertical tilt of the speaker is set by undoing the screw in the end of the
egg-shaped moulding on the bracket that has teeth which allow different
vertical tilt angles to be achieved. Once the desired vertical angle is
reached, fully tighten the "egg" screw.
Martin Audio – C115 Loudspeaker
ENGLISH
3
All material © 2007. Martin Audio Ltd. Subject to change without notice.
It is important that both the "egg" screw and "base" screw are fully tightened
once the final position of the speaker has been set.
7 CONNECTING THE C115
The loudspeaker terminals will accept stripped wires up to 1.5mm2diameter.
The wires should be stripped to approximately 8-10mm. It is important that all
the C115’s in a distributed system are wired in phase i.e. consistent polarity is
maintained throughout. Each C115 is wired so that a positive voltage on the
RED terminal causes forward motion of the speaker cone.
8 TRANSFORMER VERSIONS
The 70V and 100V versions of the C115 have an internally mounted tapped
transformer and a switch, which selects the power delivered to the
loudspeaker. The switch is located at the rear of the enclosure to the right of
the wall bracket when viewed from the rear. The switch is adjusted by means
of a small flat blade screwdriver as follows:
Switch Position (view from rear) Power
Position 1 (fully anti-clockwise) 3.75W
Position 2 7.5W
Position 3 15W
Position 4 (fully clockwise) 30W
9 WARRANTY
Martin Audio C115 Loudspeaker is warranted against manufacturing defects in
materials or craftsmanship over a period of 5 years from the date of original
purchase. During the warranty period Martin Audio will, at it's discretion,
either repair or replace products which prove to be defective provided that the
product is returned in its original packaging, shipping prepaid, to an authorised
Martin Audio service agent or distributor.
Martin Audio Ltd. cannot be held responsible for defects caused by
unauthorised modifications, improper use, negligence, exposure to inclement
weather conditions, act of God or accident, or any use of this product that is
not in accordance with the instructions provided by Martin Audio.
Martin Audio is not liable for consequential damages.
This warranty is exclusive and no other warranty is expressed or implied.
This warranty does not affect your statutory rights.
Martin Audio – C115 Loudspeaker
ENGLISH
4
All material © 2007. Martin Audio Ltd. Subject to change without notice.
10 TECHNICAL SPECIFICATIONS
C115
TYPE Ultra-compact, two-way ICT™
FREQUENCY 80Hz – 20kHz
RESPONSE 120Hz – 20kHz ± 3dB
DRIVER 1 x 5" (120mm) full-range ICT™
RATED POWER 50W AES, 200W peak
RECOMMENDED 50-200W into 4 ohms
AMPLIFIER
SENSITIVITY 88dB (1 watt @ 1 metre)
MAXIMUM SPL 105dB continuous, 111dB peak
IMPEDANCE 8 ohms
DISPERSION (-6dB) 90 degree conical
ENCLOSURE Mineral loaded polypropylene
FINISH Light grey or graphite
PROTECTIVE GRILLE Perforated steel
CONNECTORS Binding posts
OPTIONS 30w line transformer
Shielded magnet
DIMENSIONS (W) 194mm x (H) 217mm x (D) 135mm
(W) 7.6ins x (H) 8.5ins x (D) 5.3ins
WEIGHT C115 1.7kg (3.7lbs)
WEIGHT C115T 2.5kg (5.5lbs)
SHIPPING DIMENSIONS (W) 270mm x (H) 410mm x (D) 240mm
(W) 10.6ins x (H) 16.1ins x (D) 9.4ins
SHIPPING WEIGHT C115 4.5kg (9.9lbs)
SHIPPING WEIGHT C115T 6kg (13.2lbs)
Due to our policy of continuous improvement all specifications are subject
to change without notice.
Martin Audio – C115 Loudspeaker
ENGLISH
5
All material © 2007. Martin Audio Ltd. Subject to change without notice.
11 FIXING TEMPLATE
Warning
If using this template check diameter = 67mm
Martin Audio – C115 Loudspeaker
ENGLISH
6
All material © 2007. Martin Audio Ltd. Subject to change without notice.
C115 Loudspeaker
Century Point, Halifax Road, Cressex Business Park, High Wycombe, Buckinghamshire HP12 3SL, England.
Telephone: +44 (0)1494 535312 Facsimile: +44 (0)1494 438669
The Martin Experience
MARTIN AUDIO
LONDON
Please Click here to
return to main menu
Please Click here to
visit our website
All material © 2007. Martin Audio Ltd. Subject to change without notice.
MARTIN AUDIO
LONDON
The Martin Experience
ENGLISH
C115 Loudspeaker
User’s Guide
All material © 2007. Martin Audio Ltd. Subject to change without notice.
Tabla de contenidos
Otros manuales de Oradores de Martin Audio
Martin Audio
Martin Audio AQ12 Manual de usuario
Martin Audio
Martin Audio WM0.5 - SCHEMATICS Guía del usuario
Martin Audio
Martin Audio EFFECT5 - SCHEMATICS Manual de usuario
Martin Audio
Martin Audio DDX Series Manual de usuario
Martin Audio
Martin Audio Surface-mount Loudspeaker C115/C115T Manual de usuario
Martin Audio
Martin Audio W8LC - SCHEMATICS Manual de usuario
Martin Audio
Martin Audio C516 Manual de usuario
Martin Audio
Martin Audio LE2100 Manual de usuario
Martin Audio
Martin Audio W0.5 Manual de usuario
Martin Audio
Martin Audio C4.8T Manual de usuario
Martin Audio
Martin Audio SCREENSUB1A - SCHEMATICS Manual de usuario
Martin Audio
Martin Audio WS18X Manual de usuario
Martin Audio
Martin Audio DD6 - SCHEMA Manual de usuario
Martin Audio
Martin Audio AQ Series Manual de usuario
Martin Audio
Martin Audio ASX Guía
Martin Audio
Martin Audio BlacklineX SERIES Manual de usuario
Martin Audio
Martin Audio LE12JB_EN - SCHEMATICS Manual de usuario
Martin Audio
Martin Audio SCREEN4 - SCHEMATICS Manual de usuario
Martin Audio
Martin Audio Two-way Passive System Screen 2P Manual de usuario
Martin Audio
Martin Audio AQ10 Manual de usuario
