Martin Audio DX2 Guía de inicio rápido

Loading binary presets into your Martin Audio DX2

Loudspeaker Management System

Clicking here takes you to a zip folder containing the loader software and binary files.

Extract these to your hard disk. Do not run the programme from the zip folder.

Warnings

Loading presets will overwrite previously loaded factory presets - and any

changes to them (e.g. channel gain, delay, limiter settings).

To make a permanent record of changes to the user-editable parts of a preset,

you must save the preset in one of the lower number memory locations.

Make sure you have a full set of .bin files before proceeding so that you can

reload your original presets if you need to.

If you are not familiar with the Martin Audio DX2, please read the DX2

User Guide.

You should have extracted the following files to a suitable folder on your

hard drive:

MartinFlashLoader.exe – The DX2 binary preset loader software

MARTN1RLCDLC21801.bin – Binary presets for

W8LCD+W8LC+WS218X/W8LS combinations

MARTN1RLCDLCWLX01.bin – Binary presets for W8LCD+W8LC+WLX

combinations

MARTN1RLDLBLS02.bin – Binary presets for W8LD+W8L

Longbow+W8LS/WS218X combinations

MARTN1RLM218X03.bin – Binary presets for

W8LMD/LM+WS218S/W8LS combinations

MARTN1RLMWLX03.bin – Binary presets for W8LMD/LM+WLX

combinations

MARTN1RLMWMX03.bin – Binary presets for W8LMD/LM+WMX

combinations

MARTN1RLE12152101.bin – Binary presets for 4-mix LE1200, LE1500

or LE2100 systems

You will need a 9 pin male-to-female, fully wired, pin-to-pin RS232 cable (not the

null modem type).

To load the latest presets into your DX2

1) Connect the 9-pin male to 9-pin female DEE type serial lead from your

computer to the external socket on the back of the unit. Note: this lead should be

pin-to-pin - not be of the null modem type.

2) On the DX2 use the blue Menu, Back, Next and Enter keys to go into the

Interface Sub-menu and then into External Interface.

3) Once entered, setup as follows:

Mode: RS232 Mode

Wiser Wireless: No

Serial Speed: As required (e.g. 115200)

Stop MIDI Prog,Chng: Yes

Remote ID Number: 1

Press Enter to confirm

4. Run the programme MartinFlashLoader.exe.

Click Load New Preset File.

If necessary, browse to find the files you extracted earlier. Click on the preset

required (to highlight it) and click Open. The programme will attempt to

communicate with the DX2.

If the Com number (or Speed settings set in 3 above) are not the same as the

DX2 parameters, you will see something like this…

Make sure the Baud rate (Speed) matches the unit to be loaded!

Try adjusting the Com (Serial Port) number and clicking the Connect

button again. It is usually quicker to do this by trial and error as Com port

numbering can be a mystery to the average PC user!

If it succeeds the bottom right hand panel will indicate Good Response.

Click Load Now.

click OK.

You’ll see the block writing progress bar proceeding from left to right

and

you’ll see the DX2 screen graphics shuffling from right to left…

…

followed by an indicator test (all LEDs on)…

…

a short delay…

…

and then a wake-up procedure.

Selecting a particular preset

Note that each binary file will load a family of presets into your DX2. Choose the

required preset as follows:

1) Press the blue Menu button, then the Back and Next buttons to find

the Global Memory Sub Menu and press Enter.

2) Use the Back and Next buttons to find the Recall a Memory and

press Enter.

3) Use the Back and Next buttons to find the Crossover only and press

Enter.

4) Browse for the appropriate preset using the Back and Next buttons or

the Frequency knob.

Note that the DX2 will default to its previous condition if the above operations are

not completed and no buttons are pressed for 20 – 30 seconds.

Amplifier power, amplifier gain and limiter settings

We suggest you specify an amplifier capable of meeting the loudspeaker’s peak

power rating – as long as you use the correct Martin Audio limiter

recommendations. The limiter parameters protect the loudspeaker from long-

term overloads whilst the correct amplifier specification protects the loudspeaker

from transient overloads and clipping.

Limiter thresholds are factory preset for power amplifiers with the pro-audio

voltage gain* standard of 32dB (x40).

* We recommend using power amplifier voltage with known gain settings if at all

possible. Manufacturers’ sensitivity settings are not very useful as the resulting

gain figures will vary from model to model depending on their power

specifications causing spectral imbalance when using mixed amplifier set-ups.

If you use a power amplifier set to a different gain standard, make absolutely

sure it is set to that gain and adjust the limiter threshold settings as follows:

Power amplifier gain Limiter threshold adjustment

23dB Add 9dB (e.g. +4dBu becomes +13dBu)

24dB Add 8dB

25dB Add 7dB

26dB (Crown standard) Add 6dB (e.g. +4dBu becomes +10dBu)

27dB Add 5dB

28dB Add 4dB

29dB Add 3dB

30dB Add 2dB

31dB Add 1dB (e.g. +4dBu becomes +5dBu)

32dB (Industry standard) Martin Audio preset standard

33dB Decrease by 1dB (e.g. +4dBu becomes +3dBu)

34dB Decrease by 2dB

35dB Decrease by 3dB

36dB Decrease by 4dB (e.g. +4dBu becomes 0dBu)

37dB Decrease by 5dB

38dB Decrease by 6dB

39dB Decrease by 7dB

40dB Decrease by 8dB (e.g. +4dBu becomes -4dBu)

System configurations

Your Martin Audio DX2 Loudspeaker Management System must be correctly

patched.

See the following standard preset and output channel allocation details.

Note that this information may be adapted for experienced technicians to create

special user presets for the products listed – but please read the covering notes…

DX2 presets and controller o/p channel allocations

Notes

Many critical Martin Audio factory presets are locked to comply with

warranty conditions and some inter-driver delays are lock-linked to enable

delay tracking. Non-critical parameters (e.g. HF equalisation that may

need to be adjusted as humidity changes) are left unlocked for user

adjustment.

You may use the following parameters to create your own unlocked user-

presets but please be aware that alterations to critical – normally locked –

parameters could have an adverse effect on the system’s polar pattern

control and could compromise future warranty claims.

Output channels are listed with the appropriate source input channel noted

Mono outputs show the appropriately summed inputs

Where stereo output presets are ganged (e.g. Output [1+3]) only the first

of the two ganged outputs is shown (e.g. LM L LF – LM R LF settings are

always identical)

Crossover (High-pass & Low-pass) and PEQ parameters shown in blue

italics are locked in standard Martin Audio xbl library files and direct

loading binary files

Delay parameters shown in blue italics are locked and, sometimes, linked

to a reference channel delay* in standard Martin Audio xbl library files and

direct loading binary files.

The overall delay will be the lock-linked delay figure + the

reference delay* to which the locked delay is linked. This ensures

that critical inter-driver delays remain correct in the presence of reference

channel delays* that have been modified to time align the main array to

separate subwoofer system or to other arrays.

*The reference delay on most systems is left open for inter-system

alignment. Associated inter-driver delays automatically maintain inter-

driver alignment. The reference delay channel is usually the channel that

drives the loudspeaker section with the longest natural propagation delay

– for instance, the long LF horn of a W8L or W8LC) or the HF horn of a

horn + direct radiator system like the W8LM

Contents (click the appropriate series)

1 LE1200, LE1500 and LE2100

2 W8LM+W8LMD+WMX or WLX or WS218X/W8LS combinations

3 W8LC+W8LCD+WLX or WS218X/W8LS combinations

4 W8L Longbow+W8LD+W8LS/WS218X combinations

LE1200 active for 32dB amps

Format: 4 x 2 Way Crossover Name: 4 x 2-way LE1200

Output [1] Low A (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.2500 mS [Linked to Output 2]

Attack: 23mS Release: x16 at +3dB Fast at 12dB above Limiter

75.8Hz

1.00

+4.5dB

PEQ

1k00Hz

3.0

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [2] High A (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-3.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.5dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [3] Low B (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.2500 mS [Linked to Output 4]

Attack: 23mS Release: x16 at +3dB Fast at 12dB above Limiter

75.8Hz

1.00

+4.5dB

PEQ

1k00Hz

3.0

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [4] High B (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-3.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.5dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [5] Low C (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.2500 mS [Linked to Output 6]

Attack: 23mS Release: x16 at +3dB Fast at 12dB above Limiter

75.8Hz

1.00

+4.5dB

PEQ

1k00Hz

3.0

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [6] High C (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-3.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.5dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [7] Low D (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.2500 mS [Linked to Output 8]

Attack: 23mS Release: x16 at +3dB Fast at 12dB above Limiter

75.8Hz

1.00

+4.5dB

PEQ

1k00Hz

3.0

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [8] High D (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-3.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.5dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

LE1200 passive for 32dB amps

Format: 4 x 2 Way Crossover Name: 8 x LE1200

Output [1] FR A1 (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [2] FR A2 (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [3] FR B1 (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [4] FR B2 (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [5] FR C1 (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [6] FR C2 (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [7] FR D1 (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [8] FR D2 (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

35.1Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +4dB Fast at 12dB above Limiter

75.8Hz

1.5

+3.0dB

PEQ

1k00Hz

3.0

+1.0dB

PEQ

13k2Hz

1.8

+4.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

LE1500 active for 32dB amps

Format: 4 x 2 Way Crossover Name: 4 x 2-way LE1500

Output [1] Low A (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.1019 mS [Linked to Output 2]

Attack: 23mS Release: x16 at +5dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.5dB

PEQ

218Hz

1.00

+2.0dB

PEQ

303Hz

3.0

-2.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [2] High A (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-2.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.0dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [3] Low B (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.1019 mS [Linked to Output 4]

Attack: 23mS Release: x16 at +5dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.5dB

PEQ

218Hz

1.00

+2.0dB

PEQ

303Hz

3.0

-2.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [4] High B (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-2.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.0dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [5] Low C (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.1019 mS [Linked to Output 6]

Attack: 23mS Release: x16 at +5dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.5dB

PEQ

218Hz

1.00

+2.0dB

PEQ

303Hz

3.0

-2.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [6] High C (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-2.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.0dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [7] Low D (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley 1k17Hz 24dB Link/Riley

+0.0dB 0.1019 mS [Linked to Output 8]

Attack: 23mS Release: x16 at +5dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.5dB

PEQ

218Hz

1.00

+2.0dB

PEQ

303Hz

3.0

-2.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [8] High D (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

1k33Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

-2.5dB 0.0000 mS

Attack: 2.0mS Release: x16 at +1dB Fast at 12dB above Limiter

1k75Hz

6.0

-6.0dB

PEQ

2k72Hz

3.0

-2.0dB

PEQ

4k24Hz

1.8

-2.5dB

PEQ

13k2Hz

2.0

+8.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

LE1500 passive for 32dB amps

Format: 4 x 2 Way Crossover Name: 8 x LE1500

Output [1] FR A1 (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [2] FR A2 (Source = Input A)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [3] FR B1 (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [4] FR B2 (Source = Input B)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [5] FR C1 (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [6] FR C2 (Source = Input C)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [7] FR D1 (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Output [8] FR D2 (Source = Input D)

Freq.

Gain

Type

Highpass:

Gain:

Limiter:

Lowpass:

Delay:

Clip Limiter:

PEQ 1 PEQ 2 PEQ 3 PEQ 4 PEQ 5 PEQ 6 PEQ 7 PEQ 8 PEQ 9

24.8Hz 24dB Link/Riley >32k0Hz 24dB Link/Riley

+0.0dB 0.0000 mS

Attack: 23mS Release: x16 at +6dB Fast at 12dB above Limiter

70.2Hz

1.00

+4.0dB

PEQ

454Hz

1.00

+1.5dB

PEQ

13k2Hz

2.0

+2.5dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

1k00Hz

3.0

+0.0dB

PEQ

Tabla de contenidos

Otros manuales de Sistema de altavoces de Martin Audio

Martin Audio

Martin Audio DX1.5 Manual de usuario

Martin Audio

Martin Audio EM120 - SCHEMATICS Guía

Martin Audio

Martin Audio Cinema Screen 4 Manual de usuario

Martin Audio

Martin Audio Compact Three-way Mid-high System W8C Manual de usuario

Martin Audio

Martin Audio WPM Manual de usuario

Martin Audio

Martin Audio BX2 Manual de usuario

Martin Audio

Martin Audio Screen Channel Manual de usuario

Martin Audio

Martin Audio Cinema Screen 6 Manual de usuario

Martin Audio

Martin Audio Cinema Screen 3 Manual de usuario

Martin Audio

Martin Audio EM15 Manual de usuario

Martin Audio

Martin Audio AQ8 Manual de usuario

Martin Audio

Martin Audio MLA Mini Manual de usuario

Martin Audio

Martin Audio W2 Manual de usuario

Martin Audio

Martin Audio LE1500 Manual de usuario

Martin Audio

Martin Audio Cinema Effect 3 Manual de usuario

Martin Audio

Martin Audio Screen 5B Manual de usuario

Martin Audio

Martin Audio Two-way Passive Surround System Effect 5 Manual de usuario

Martin Audio

Martin Audio O-LINE Manual de usuario

Martin Audio

Martin Audio Three-way Passive System Screen 4P Manual de usuario

Martin Audio

Martin Audio Longbow W8L Guía del usuario

Martin Audio

Martin Audio CDD12-WR Manual de usuario

Martin Audio

Martin Audio WAVEFRONT COMPACT - APPLICATIONS GUIDE Guía del usuario

Martin Audio

Martin Audio Blackline F8 Manual de usuario

Martin Audio

Martin Audio Cinema Screen 5 Manual de usuario

Manuales populares de Sistema de altavoces de otras marcas

JVC

JVC CA-MXK5R Manual de usuario

LG NB4532B Manual de usuario

JVC

JVC CA-FSH100 Manual de usuario

5Core

5Core Pro Series Manual de usuario

EAW

EAW MQV1394e Manual de usuario

Lynx

Lynx GXR-LA10A Manual de usuario

iLive

iLive ITB066B Manual de usuario

RDX

RDX QuickStation 4 Manual de usuario

Electro-Voice

Electro-Voice S-122 Manual de usuario

Sven

Sven SPS-619 GOLD Manual de usuario

Pioneer

Pioneer CS-7070 Manual de usuario

EAW

EAW UB82e Manual de usuario

Sondpex

Sondpex Active Speaker System and Digital Music... Manual de usuario

JVC

JVC NX-PN7 Manual de usuario

Marshall Amplification

Marshall Amplification AR-DM61-BT Manual de usuario

Yamaha

Yamaha NX-A01 - Speaker Sys Manual de usuario

SE Audiotechnik

SE Audiotechnik I-LINE Manual de usuario

Gemini

Gemini WRX-843 Series Manual de usuario