Marshall Electronics VS-541-HDSDI Manual de usuario

MarshallElectronics
VS‐541‐HDSDI/HDI
2.0MegapixelIPZoomCamera
X20 Zoom CMOS
UserManual

User Manual VS-541 – V1.0 Page 2 of 52 2/7/12
Copyright © January 2012, Marshall Electronics, Inc.
All Rights Reserved. This document may not be copied.
Trademarks
Other trademarks used in this document are registered trademarks or manufacturer or vendor
trademarks associated with the products.
Disclaimer
Product options and specifications can be changed without notice. The information in this
manual is furnished for informational use only and should not be construed as a commitment
by Marshall Electronics, Inc. Marshall Electronics, Inc. assumes no responsibility or liability for
any errors or inaccuracies that may appear in this publication.
Safety Precaution
Make sure to turn off the power before installing the system.
Do not install under the direct sunlight or in dusty areas.
Make sure to use the product within the temperature and humidity specified.
Do not operate the product in the presence of vibrations or strong magnetic fields.
Do not put electrically conducting materials in the ventilation hole.
Do not open the top cover of the products. It may cause a failure or electric shock on the
components.
To prevent from overheating, make sure to keep the distance at least 10 cm from the ventilation
hole.
Make sure proper voltage before connecting the power.
We appreciate your IP Camera Purchase.
Before installing the product, please read the following with care.

TABLE OF CONTENTS
__________________________________________________
User Manual VS-541 – V1.0 Page 3 of 52 2/7/12
1 - Introduction......................................................................................................................4
1.1 About this Manual ...................................................................................................4
1.2 Features..................................................................................................................4
1.3 Product and Accessories ........................................................................................5
1.4 System Connections...............................................................................................8
2 - Installation........................................................................................................................9
3 - System Operation..........................................................................................................10
3.1 Remote Video Monitoring......................................................................................10
3.2 Initialization of IP address.....................................................................................13
4 - Remote Configuration....................................................................................................14
4.1 Using Web Brower................................................................................................14
4.2 System Configuration............................................................................................15
4.3 Video Configuration ..............................................................................................18
4.4 Audio Configuration...............................................................................................23
4.5 Network Configuration ..........................................................................................25
4.6 Serial Configuration ..............................................................................................32
4.7 Event Configuration ..............................................................................................34
4.8 Preset Configuration.............................................................................................39
4.9 Record Configuration............................................................................................40
4.10 User Configuration..............................................................................................46
4.11 Camera Configuration.........................................................................................48
5 - VS Manager...................................................................................................................52

1-Introduction
___________________________________________________________________________
User Manual VS-541 – V01.0 Page 4 of 52 2/7/12
1.1 About this Manual
This User Manual provides information on operating and managing this premium
network camera. It includes instructions for installation, operation and configuration,
as well as troubleshooting tips.
1.2 Features
This IP Camera is a network-based system with remote live monitoring, audio
monitoring and control via an IP network such as LAN, ADSL/VDSL, and Wireless LAN.
Camera
1/3” CMOS Image Sensor
X20 Optical Zoom, X12 Digital Zoom
True Day & Night (ICR)
VS-541 = CVBS & IP
VS-541-HDSDI = HDSDI & IP
Video
Highly Efficient Compression Algorithm, H.264 & MJPEG Support
Resolutions: CIF (352x240) – Full HD (1920x1080)
Wide Range of Transmission Rates: 32kbps ~ 8mbps
Various Transmission Modes: CBR, VBR
Motion Detection
Audio
Multi-Transmission Mode: Simplex (Megapixel IP Camera Client PC or Decoder,
Client PC or Decoder Megapixel IP Camera), Full Duplex
Network
Fixed IP & Dynamic IP (DHCP) Support
1:1, 1:N Support
Multicasting
Various Protocol Support Types: TCP/IP, UDP, Multicast, DHCP, SMTP, HTTP,
SNMP, RTP, RTSP

1-Introduction
___________________________________________________________________________
User Manual VS-541 – V01.0 Page 5 of 52 2/7/12
Serial Data
RS-485 Support
Data Pass-Through Mode: Serial Data Communication between IP Camera and
Decoder
Sensor and Alarm
Event Alarm Notification
1 Alarm Sensor Input and 1 Alarm Output Relay are available
User Interface
Diagnose and upgrade through dedicated program called VS Manager
System Configuration using Internet Explorer
High Reliability
Reliable Embedded System
1.3 Products and Accessories
2.0 Megapixel IP
Zoom Camera Quick Guide SW and User Manual CD

1-Introduction
___________________________________________________________________________
User Manual VS-541 – V01.0 Page 6 of 52 2/7/12
Part Names and Functions
Rear View
Connector Function
1. Ethernet/802.3af Ethernet Port/802.3af LED:
Booting and System Check
2. RESET Button Initialization of Network Setting
3. AUDIO IN Audio Input
4. AUDIO OUT Audio Output
5. POWER IN DC 12V
6. SENSOR/ALARM Sensor Input/ Alarm Output
7. RS-485 RS-485 Port
8. VIDEO OUT Composite / HD-SDI / HDMI Video Output
(Depending on Models)
9. SD CARD SD Memory Card Slot
②
E
①

1-Introduction
___________________________________________________________________________
User Manual VS-541 – V01.0 Page 7 of 52 2/7/12
1.4 System Connections
The IP Camera can be connected in one of two ways:
1) 1 to 1 connection where one camera is connected to one PC client or a decoder
system, or 2) 1 to many connections where one system can be connected to several
PCs and decoder systems (the video server can work as a video decoder which takes
the data from a video server or IP camera, decodes and outputs analog video).
Topology
Generally, the IP Camera and PC or a Decoder is connected in a 1-to-1 mode or a 1-to
many configuration:
1:1 Connection
One camera is installed at a site where video images are transmitted. A PC or a
decoder is installed at a central location to receive and view the video images on an
analog monitor. Audio and serial data are transferred in either direction.
1:N Connection
In this configuration, a site can be monitored from many remote central locations.
Maximum connections would be limited by network bandwidth connection. Functionally,
the VMS (Video Management System) software provided can replace the decoder.
Site Remote Center (Decoder) Remote Center
Site Remote Center (PC SW)
o
r
Site Remote Center
or
o
r

1-Introduction
___________________________________________________________________________
User Manual VS-541 – V01.0 Page 8 of 52 2/7/12
Multicast Mode
If the network supports multicasting, a large number of decoders can be used to receive
video effectively from a camera using a single streaming of video and audio. However,
Multicast Mode is possible only when the network environment supports multicast.
Relay
Video and Audio Data can be retransmitted from one center to another center. The
arrangement is useful when the limited network bandwidth can allow more than one
center to monitor this site.
VMS (Video Management System)
VMS (Video Management System) is a Window-Based Remote Monitoring Program in
used to monitor or control video, audio, and events in real time from several IP cameras
or video servers. Please refer to the VMS User Manual for more details.
Site Center 1(Decoder) Center 2 (Decoder)
VMS
Site Remote Center
Site Remote Center (Decoder)

2-Installation
___________________________________________________________________________
User Manual VS-541 – V01.0 Page 9 of 52 2/7/12
2.1 Connecting Network (LAN)
Connect the Power Adaptor to IP Camera
Connect Network Cable to Ethernet Port
To display video through Composite Port, after connecting each port to a monitor,
set preview option “ON” on the web-viewer page.
2.2 Connecting Audio
Audio is Full-Duplex. It is possible to set the mode as Tx-Only, Rx-Only or Tx-Rx.
Connect Audio Input and Output Ports to audio devices accordingly.
The Audio Signal required is Line Level, so audio equipment with an amp, mixer or
other amplifier should be used.
2.3 Connecting Serial Ports
RS-485 on the IP camera can be connected to external equipment such as a PT
Receiver, etc. PC client can send PT commands to the external equipment via the
serial port. When a decoder system, instead of PC client, is connected to the IP
camera, the serial port and decoder system works in pass-through mode; data from one
port is delivered to the other port and vice versa.
2.4 Connecting Sensor and Alarm
Connect Sensor and Alarm Devices to corresponding terminals accordingly.
2.5 Connecting Power
After confirming the Power Source, connect power adaptor and connect the 12VDC
connector to the IP camera.
2.6 Check if it Works
Once the power is supplied to the IP camera, it will start booting. The IP camera will
boot up to an operating mode after approximately 40-60 seconds. The green LED on
the Ethernet Port will flash indicating the IP camera is ready. Software provided on the
disc called VS Manager, allows you to check the IP address and other network details
of the IP camera. Please refer to the VS Manager manual for instructions on how to find
the camera’s IP address and details to modify if necessary.

3-System Operation
__________________________________________________________________________
User Manual VS-541 – V01.0 Page 10 of 52 2/7/12
3.1 Remote Video Monitoring
There are two ways to monitor video when the center system and IP camera are
connected. In order for a proper operation, an IP address must be set accordingly.
Please refer to the VS Manager Manual enclosed with product for further details.
Default ID : admin Default Password : 1234
Video Monitoring using Internet Explorer
Open Internet Explorer and enter camera’s IP address. The system will ask for
confirmation to install Active-X control. Once authorized, the Internet Explorer will start
to display video images from camera as shown below:
Default IP Address : http://192.168.10.100
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara IP de Marshall Electronics





















