Maripak COMPACK i Series Manual de usuario
Tel: +78123632021 info@rospol.com www.rospol.com
SHRINK WRAP MACHINES
for compack-i series
Инструкция и каталог запчастей Maripack Compack-i 5800
1
Table Of Contents
2Certicate of conformity
3Service inquiries
3Warranty
4Safety information
5Contents of your package
5Your machine
6Mounting the legs
6Control panel
7Getting prepared
Loading the lm
Sealing
Shrinking
Magnetic hold down
9Periodic care
10 Technical specications
11 Maintenance
11 Troubleshooting
13 Spare part
15 Electrical diagram
2
EC Decleration of Conformity
According to EC Machinery Directive 89/392/EEC , Annex II A
We herewith declare, as
that the following described machine in our delivered version complies with the appropriate ba-
sic safety and health requirements of the EC Machinery Directive 89/392/EEC based on its design
and type, as brought into circulation by us. In case of alteration of the machine, not agreed upon
by us this decleration will lose its validity.
Description of the machine/machinery part;
Machine Type: .................
Serial Number: .................
Applicable EC Directives: (89/392/EWG) I.d.F. 93/44/EWG,
(73/23/EWG), (89/339/EWG) I.d.F. 93/31/EWG
Applicable Harmonized Standards: EN 60204 -1:1992 ; EN 292-1:1991; EN 292-2 A1:1995
EN 294:1992; EN 349:1993; VBG 76:1993; pr EN 415-3:1995
Applicable National Technical
Standard and
Specication: VBG 76
Date / Authorized Signature:
Title of signature:
3
In case of damage or a service requirement, please contact to your nearest authorized distributor
or to the manufacturer company addressed.
MARİPAK Packaging Ltd.
Service Inquiries
Warranty
This machine is under the warranty of the manufacturer for a period of one year beginning with
the date of delivery. Any interaction related to this warranty will be carried out between the rst
ocial invoiced company/person and the authorized distributors.
We hereby guarantee to replace any defected part of the machine in the warranty period. This
warranty also covers the repairing of the machine. If the repairing is carried out in the client’s
plant, the list price for service cost is invoiced to the client which is issued by the manufacturer.
The defected part will not be charged. The unit must not be opened by an unauthorized person.
It can only be opened by the approval of your authorized distributor. Any defected part must be
sent back to the distributor for replacement under warranty.
The manufacturer and the authorized distributor will not be responsible and this warranty will not
be valid under these conditions:
If the machine is not installed properly as described in this manual,
If the power supply is insucient or incorrect,
If anyone is harmed due to improper handling or improper power supply.
•
•
•
4
If the consumable parts are demanded or there is a problem related to any consumable part as
described below:
Consumable parts: Cutting blade, rubber, teon tape, blade beds and its corner and side
connections.
If the machine is not used as described in this manual,
If a change is made on the machine by an unauthorized person.
The manufacturer company will not be responsible for any problem due to translation mistakes.
•
•
•
Safety Information
Please read the following information before connecting your machine to a power supply.
Plug in the machine to an appropriate voltage as shown on page 15-16.
Check if the power supply is correct for the necessary connection given in the electrical diagram in
this manual.
Do not touch the sealing blade shown in Figure 1 (number 15) during operation or right after ope-
ration.
Do not touch the back side of the heating chamber which is at the back side of your machine. This
part of the unit is hot and might harm.
Do not lift the mesh hood (number 17) during operation. The fan might cause harm.
Before plugging in the machine make sure that you have xed it on a dry and humid-free ground.
Check the warning signs and labels on the machine.
Lock the front casters of the table to keep the machine steady.
•
•
•
•
•
•
•
•
5
Contents Of Your Package
Please make sure that you have received all the items listed in the following table with your pack-
age.
Operating and instructions manual 1 Pcs
Main unit 1 Pcs
Conical lm holders 2 Pcs
Film holder bar 1 Pcs
Teon tape 1 Pcs
Rubber pad 1 Pcs
Cutting and sealing blade 1 Pcs
Allen key to screw conical lm holders 1 Pcs
Metal legs with casters 4 Pcs
Your Machine
Legends
1. Control panel
2. Transparent hood
3. Handle
4. Main body
5. Film holding bar
6. Working plate
7. Film opener plate side
8. Torsion bar
9. Perforators
10. Film holder
11. Legs
12. Front casters with brake
13. Perforator bars
14. Electromagnet (solenoid)
15. Sealing blade and beds
16. Electrical components (inside)
17. Mesh hood
18. Main on-o switch
19. Back casters (2 pieces)
Figure 1
6
Mounting The Legs
The outlook of the table and the mounting is shown in the following gures.
Control Panel
The control panel of the machine is shown in the gure below.
ON-OFF switch,
Digital controller unit
Legends
1. Indicates the temperature level of the
sealing,
2. Indicates that the machine is ready to
run/operate,
3. F mode indicates the‘FAN ON’mode. To
disable the FAN and proceed with‘SEAL
ONLY’mode, push the OK button.
4. Indicates the actual room temperature.
Figure 2
Figure 3
Figure 4
INFO! In each cycle the room temperature will be exchanged with cooler air. The most accurate tem-
perature values can only be read without packaging process in 5 minutes. Due to this fact, dramatic
temperature drops during cycles can be considered as a normal case.
7
Getting Prepared
Loading Film
To take out the holders, rst remove the lm holder bar and then unscrew the conical holders.
After one of the sides is xed, insert the lm roll on the bar and screw back the conical head to x
on the roll, as shown in gure 5.
Films are centre-folded and maybe produced either rolled in clockwise or counter clockwise as
shown in gure 5. Your machine is capable for either application.
After loading the lm, (when mounting the loaded bar) make sure that the opening side of the
lm faces the front side of the machine (device).
Pull the working plate, the plate which slides back and forth, towards the operator. The lm must
pass over and under the product plate. (The product plate must remain in between the upper
and lower leaves of the lm.) As the opening side of the lm faces the operator, the product can
easily be inserted.
You need to cut and seal the lm at least once to start the rst packaging. Place your product on
the plate together with the lm and slide together into the chamber of the machine.
Figure 5
8
The lm and the product must be positioned together close to the front-right corner of the cham-
ber. There must be 1-2 cms of distance between the edge of the chamber and the product.
Close the hood to cut the edges (Figure 6). A small amount of lm will be wasted.
IMPORTANT NOTE: To avoid wasting lm, you should choose the correct size of lm. Film widths are avail-
able generally between 20 cm and 60 cm. Sizes vary with increments of 5 cms (ie 20, 25, 30 and so on).
Sealing
One of the functions of the machine is“SEAL ONLY”operation. During this operation the fan won’t
work. You can wrap the package without shrinkage. To enable or disable the“FAN ON/OFF”mode,
just push the OK button (Figure 4, number 3).
Shrinking
The fan and the blade will automatically start functioning as the hood (heating chamber) is
closed.
During the process, the fan will accumulate hot air on the package and within a very short time
such as 3-5 seconds you can get your package shrunk.
WARNING: Always keep your package on the right corner close to the operator.
Magnetic hold down
Once the hood is closed manually, it will remain closed automatically by the magnetic hold down
mechanism. In such models the operator will be available to prepare the next coming package.
Figure 6 Figure 7
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
