Manrose Cucina Manual de usuario

Installation Instructions Speciﬁcations are subject to change without notice Page 1

[email protected] | www.manrose.co.nz Distributed by Simx Limited

Cucina 100mm Kitchen Fan

Thank you for purchasing this quality kitchen fan.

To ensure correct function and safety, please read all instructions before using the product and keep all instructions for future reference.

Mounting Switching Order Code

Wall, Panel or Ceiling Pull Cord FAN7201

When using electrical appliances, basic safety precautions should always

be followed to reduce the risk of ﬁre, electrical shock and personal injury.

ABCDEØF

231 261 137 79 58 98

DIMENSIONS

SPECIFICATIONS

Duct

(mm)

Fan

Speed

Max.

Fan Watts

(W)

Max.

Fan Pressure

(Pa)

Free Air Fan Performance Specific

Fan Power

(W/l/s)

Sound

dB(A)

(l/s) (m3/hr)

100 High

Medium

236

140

263

140

0.82

1.05

TECHNICAL

Supply Max. Operating Temp IP Rating

220-240V AC, 50Hz 40°C IPX4

Compliance: AS/NZS60335-2.80:2016

This powerful centrifugal fan, designed for easy installation and low

running noise, features kitchen and laundry installation boost levels

as well as a low speed option for long term trickle. The fan also

features a washable grease ﬁlter.

For best results, Simx recommend this product for either kitchen or

laundry applications.

Following these installation instructions, this product will comply with

the G4 Building Code for kitchens and bathrooms once installed.

The Healthy Homes Standard requirement for bathroom or kitchen

installation in a rental property is also met.

C D

Installation Instructions Speciﬁcations are subject to change without notice Page 2

[email protected] | www.manrose.co.nz Distributed by Simx Limited

Cucina 100mm Kitchen Fan

REGULATIONS AND STANDARDS

Choosing the Right Fan to Comply

Fans cannot be selected on the basis of free-air performance only. Fans must now be selected on the basis of the complete installed system

performance for a designated room as per the table below.

1) Toilets only require ventilation if they have no openable windows

2) Simx recommends 40 l/s for laundries with unvented non-condensing tumble dryers as covered in AS 1668: Part 2 2012

New Zealand Building Code and Healthy Homes

The following two category requirements have been established for mandatory extraction ventilation in New Zealand.

The New Zealand Building Code for New Building Consents

The building regulatory system sets out a framework to promote good quality decisions being made during the Building Consent process. The

legislation and regulations work together, as the building regulatory system. The functional clauses of the NZ Building Code are grouped and

described by a letter and number. Clause G of the NZ Building Code covers services, with G4 setting out the performance requirements for

ventilation. The Building Code is enshrined in law. The New Zealand Building Code, G4, has been changed. This is supported by Acceptable Solution

G4/AS1 Fourth Edition that specifies mechanical ventilation in accommodation units that contain cooktops, showers and baths.

Residential Tenancy Regulations to the Healthy Homes Standards

Residential Tenancy Regulations for rental properties only is changing to the Healthy Homes Standards, sub part 4 - Ventilation Standards.

Complying with the Acceptable Solution G4/AS1

To comply, the mandatory mechanical extract system must deliver minimum airflow rates for the complete installed ventilation system. This means

that airflow rates must deliver the airflow after resistance of the ducting, internal and external grilles, as well as all other accessories, such as

backdraught shutters, are included.

Fan selection is important as some types are far better at overcoming ducting system pressure drops.

Additionally, the quality of the ducting system installation can be all important. Rigid duct systems are best as they are the most efficient. Good

installation practice is vital for flexible duct systems.

Room Airflow Rate (min.)

Intermittent Continuous

Toilet1) 25 l/s 10 l/s

Bathroom/shower 25 l/s 10 l/s

Laundry2) 40 l/s -

Kitchen 50 l/s 12 l/s

Duct Supports

Exterior Grille

Airflow

Interior Grille

Sealant Cavity

Sleeve

Maximum length of

flexible ducting

Minimum radius =

diameter of ducting

Preferred flexible

ducting route

Peaks and troughs

Restrictions

Installation Instructions Speciﬁcations are subject to change without notice Page 3

[email protected] | www.manrose.co.nz Distributed by Simx Limited

Cucina 100mm Kitchen Fan

KITCHEN FAN INSTALLATION AND ELECTRICAL CONNECTION MUST

BE CARRIED OUT BY A REGISTERED ELECTRICIAN

BEFORE INSTALLING THE KITCHEN FAN, MAKE SURE YOU HAVE TURNED OFF THE MAIN ELECTRICITY

SUPPLY. DO NOT TURN IT BACK ON UNTIL THE KITCHEN FAN IS FULLY

INSTALLED AND READY TO USE.

ALL ELECTRICAL WORK MUST BE CARRIED OUT BY A REGISTERED ELECTRICIAN IN ACCORDANCE

WITH THE LATEST WIRING RULES AS/NZS3000.

CAUTION

• Before use, please check that the supply voltage and that of the appliance are the same (see product rating label).

• All wiring and wiring connections must comply with all current national wiring rules and regulations including AS/NZS3000:2018, or latest

edition thereof.

• Any changes or modiﬁcations made or attempted to this product, without the prior written approval of the manufacturer, will void any and all

stated warranties.

• This fan is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they are capable of, and have been given supervision or instruction concerning use of the appliance by a person responsible

for their safety.

• Precautions must be taken to avoid the back-ﬂow of gases into the room from the open ﬂue of gas or other fuel-burning appliances.

WARNING

• Do not insert or allow foreign objects to enter any ventilation openings, as this may cause an electric shock, ﬁre or damage to the fan.

• Do not put ﬁngers or foreign objects into the grille while in operation.

• To prevent overheating of this fan, keep the air inlets and outlets clean and free of anything that may cause blockage. Check all inlets and

outlets from time to time to ensure it is clear of any dirt or dust accumulation. DO NOT COVER.

• Do not use it in areas where gasoline, paint, or ﬂammable liquids are used or stored.

• This product contains recyclable materials. Do not dispose of this product as unsorted council waste. Please contact your local council for the

nearest collection point.

KITCHEN FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING INSTALLATION OR MAINTENANCE

IMPORTANT

• The fan should only be used in conjuction with ﬁxed wiring.

• The cross-sectional area of supply cord used should be ranged from 1 -1.5mm2with the appropriate sized protection device.

• Cable entry can only be made from the rear of the fan.

• The fan is suitable for connection to 220-240V AC 50Hz supply.

• The fan is a Class ll double insulated product and MUST NOT be earthed.

• Check all connections have been made correctly and securely fastened.

• Ensure the impeller rotates and is free of any obstructions.

Installation Instructions Speciﬁcations are subject to change without notice Page 4

[email protected] | www.manrose.co.nz Distributed by Simx Limited

Cucina 100mm Kitchen Fan

INSTALLATION

A backdraught shutter assembly is supplied. It is packed inside the product during

transport. It is designed to block the duct when the fan is off in order to prevent cold

draughts from outside entering the building. To use it, push it on to the end of the

exhaust spigot (Fig. 1) with the hinges on the ﬂaps vertical. It is not required when the

fan is set up to run continuously.

The Plate Fascia and Fine Filter Kit (DCT4529), shown in Fig. 3 and Fig.4, is an

optional extra kit that can be purchased separately.

Wall Mounting

1. Remove the front cover assembly by slackening the two screws by two turns

(Fig. 2 & 3). Lift the front cover assembly away from the bottom edge ﬁrst, then

the top edge.

2. Cut a 115mm diameter hole through the wall, ensuring that there is sufﬁcient

space for the product to be installed and that the ﬁlter (Fig. 4) can be removed

for maintenance.

3. Insert the wall sleeve with the larger diameter sleeve on the room-side and

cement the ends into position ﬂush with the wall faces. The wall sleeve should

be angled downwards, away from the fan, to allow any condensation to drain to

the outside.

4. Using the grille’s back plate as a template, mark the ﬁxing hole centres on the

wall. Drill and plug the wall and ﬁx the grille into position. Ensure the louvres are

pointing downwards.

5. Set-up the appropriate speed selection and other features as outlined in SETUP.

6. Remove the small terminal block cover in the top right corner (Fig. 4).

7. Using the fan chassis as a template, carefully sliding the spigot into the wall

liner, mark the ﬁxing hole centres on the wall. Alternatively, the cardboard

ﬁtment can be used as a template.

8. Drill and plug the wall using the ﬁxings provided.

9. Feed the wiring through the hole near the terminal block and secure the fan into

position using the screws provided.

10. Select and follow the appropriate wiring diagram in WIRING CONNECTIONS.

11. Replace the terminal block cover (Fig. 5).

12. Ensure the impeller (Fig. 4) rotates freely.

13. Replace the front cover assembly and tighten the two screws (Fig. 2 & 3).

14. Make sure that all covers are on correctly to ensure the optimum performance

and water ingress protection of the fan.

15. Switch the mains power supply on and check the fan is operating correctly.

Fig. 1

Fig. 3

Fig. 2

Spigot

Flaps (vertical)

Backdraught

Shutter Assembly

Cover Assembly

Cover Screws

Plate Fascia &

Fine Filter Kit

DCT4529

Cover Screws

Installation Instructions Speciﬁcations are subject to change without notice Page 5

[email protected] | www.manrose.co.nz Distributed by Simx Limited

Cucina 100mm Kitchen Fan

INSTALLATION

A backdraught shutter assembly is supplied. It is packed inside the product

during transport. It is designed to block the duct when the fan is off in order to

prevent cold draughts from outside entering the building. To use it, push it on to

the end of the exhaust spigot (Fig. 1) with the hinges on the ﬂaps vertical. It is

not required when the fan is set up to run continuously.

The Plate Fascia and Fine Filter Kit (DCT4529), shown in Fig. 3 and Fig.4, is an

optional extra kit that can be purchased separately.

Panel or Ceiling Mounting

1. Remove the front cover assembly by slackening the two screws by two

turns (Fig. 2 &3). Lift the front cover assembly away from the bottom edge

ﬁrst, then the top edge.

2. Cut a 105mm diameter hole through the wall, then suitable screw holes

in the panel, ensuring that there is sufﬁcient space for the product to be

installed and that the ﬁlter (Fig. 4) can be removed for maintenance. Either

the cardboard ﬁtment or the fan chassis can be used as a template. The

spigot can be removed temporarily to make it easier. (Fig 1 & 4).

3. Set-up the appropriate speed selection and other features as outlined in

SETUP.

4. Remove the small terminal block cover in the top right corner (Fig. 4).

5. Attach the ducting to the spigot and locate the fan into the hole in the

panel. Feed the wiring through the hole in the chassis next to the terminal

block as you do so (Fig. 5).

6. Secure into position using appropriate ﬁxtures.

7. Select and follow the appropriate wiring diagram in WIRING CONNECTIONS.

8. Replace the terminal block cover (Fig. 5).

9. Ensure the impeller (Fig. 4) rotates freely.

10. Replace the front cover assembly and tighten the two screws (Fig. 2 & 3).

11. Make sure that all covers are on correctly to ensure the optimum

performance and water ingress protection of the fan.

12. Switch the mains power supply on and check the fan is operating correctly.

Fig. 4

Fig. 5

Terminal

Block Cover

Filter

Impeller

Chassis

Assembly

Cover

Assembly

Spigot

PCB Cover

and Screws

Terminal Block

Cable Clamp

Terminal

Block Cover

Installation Instructions Speciﬁcations are subject to change without notice Page 6

[email protected] | www.manrose.co.nz Distributed by Simx Limited

Cucina 100mm Kitchen Fan

WIRING CONNECTIONS

Use 0.75mm2cable

1. Use the cable clamp provided (Fig. 5).

2. Check all connections have been made correctly and

ensure all terminal connections are securely fastened.

SERVICING AND MAINTENANCE.

1. Following installation, the fan should be inspected and cleaned on a regular basis to ensure there is no build up of dirt or other deposits.

2. If ﬁtted with the metal grease ﬁlter, remove the metal grease ﬁlter (Fig. 2) from the front cover assembly by gently popping it out from it’s

holding clips on one side of the front cover assembly.

3. Wash the metal grease ﬁlter in either a dishwasher or in warm soapy water. Dry before reﬁtting into the cleaned front cover assembly.

4. Clean the front cover assembly by either wiping the inlets and front face with a damp (not dripping wet) cloth or by washing in warm soapy

water. Dry before reﬁtting the metal grease ﬁlter and replacing.

5. Turn the power to the fan back on.

The fan has sealed for life bearings, which do not require lubrication.

SETUP

1. SELECTING THE BOOST SPEED *

Link terminal 3 to one of the following:

a. Terminal 1 = Medium (Laundry) speed

c. Terminal 2 = High (Kitchen) speed

* The Ls connection (Fig.8) is optional and if

activated through a standard wall switch, pull cord

switch, PIR or sensor, will switch the fan to either

Medium or High speed depending on which speed

has already been selected.

Pulling the pull cord will cycle the fan through Off,

Trickle, or, depending on which speed has already

been selected, Medium or High.

LOCATING THE FAN

Fig. 8

Fig. 6

Fig. 7

495846 A 0420

Pull Cord

Lamp

Ceiling Junction

Pull Cord

Installation Instructions Speciﬁcations are subject to change without notice Page 7

[email protected] | www.manrose.co.nz Distributed by Simx Limited

Cucina 100mm Kitchen Fan

Description Order Code

Plate Fascia and Fine Filter Kit DCT4529

FITTING THE PLATE FASCIA AND FINE FILTER KIT

This fascia and ﬁlter kit is available as a separately purchased

replacement for the Cucina Kitchen Fan (FAN7201) front grille.

Cover Assembly

Cover Screws

Plate Fascia &

Fine Filter Kit

Cover Screws

1 Slacken the two front cover assembly

screws by two turns

2 Lift the front cover assembly away from the fan

chassis bottom edge ﬁrst and then the top edge

4 Fit the inner cassette cover supplied onto the

fan chassis with screws provided

6 Tighten the two fascia and ﬁlter kit screws

3 Remove the inner cover

Filter

Plate Fascia

Inner

Cassette

Cover

Screws

5 Fit the fascia and ﬁlter kit onto the fan chassis

top edge ﬁrst and then the bottom edge

PUB01600 2008

PLATE FASCIA AND FINE FILTER KIT

Simx Warranty Information

In this warranty:

We means Simx;

You means the consumer of the Goods

Supplier means the authorised distributor or retailer that sold you the Goods in New Zealand or Australia; and

Goods means the Simx product accompanied by this warranty and purchased in New Zealand or Australia.

The beneﬁts provided to you under the following warranty are in addition to any other rights and remedies available

to you under the law:

1. If, during the time from the date of purchase (Warranty Period), there is a defect in the Goods due to improper

workmanship or material, we will replace or repair the Goods without charge. Any replacement product is

warranted only for the time remaining on the original Warranty Period.

2. We are not obliged to replace or repair the Goods under clause 1 if the Goods have been improperly stored,

installed, connected, used, operated, repaired, damaged, abused, tampered with, altered (without our written

approval), or not maintained in accordance with our recommended installation, connection and operating

instructions.

3. We exclude liability for:

a) consequential loss or any other loss or damage caused to property or persons arising from any cause

whatsoever;

b) damage to consumable items such as lamps and starters; and

c) damage arising from normal wear and tear.

4. In order to claim under this warranty you must, within the Warranty Period, return the Goods to the Supplier,

together with the original proof of purchase including the details below:

Supplier Name _____________________________

Date of Purchase _____________________________

Model Number _____________________________

Invoice/Receipt No. _____________________________

5. This warranty does not cover the cost of claiming under the warranty or transporting the Goods to and from the

Supplier.

Our Goods come with guarantees that cannot be excluded under the New Zealand and Australian Consumer Law.

You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if the Goods fail to be of

acceptable quality and the failure does not amount to a major failure.

To speak to someone about your Simx product or claiming under this warranty, please contact:

Simx Ltd New Zealand

p: +64 9 259 1660 f: +64 9 259 1661

www.simx.co.nz

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Máquina de fax de otras marcas

Samsung

Samsung SF-515 Manual de usuario

Radio Shack

Radio Shack TFX-1031 Manual de usuario

imagistics

imagistics 2030 Manual

Panasonic

Panasonic KX-FL501C Manual de usuario

Panasonic

Panasonic KX-FP200L Manual de usuario

Furuno

Furuno FAX-30 Manual de usuario

Savin

Savin 3740 Manual

Sharp

Sharp FO-51 Manual de usuario

Muratec

Muratec MFX-C3035 Manual de usuario

Panasonic

Panasonic KX-PD505DL Manual de usuario

Panasonic

Panasonic KX-FC265CX-S Manual de usuario

Canon

Canon FAX-L400 Manual de usuario

Ricoh

Ricoh 1000L Guía de inicio rápido

Sharp

Sharp FO-3150 Manual de usuario

Kyocera

Kyocera KM-F1060 Manual de usuario

Sharp

Sharp FO-2970M Manual de usuario

Panasonic

Panasonic KX-F850 Manual de usuario

Panasonic

Panasonic KX-FLM652CX Manual de usuario