Manrose MANI3000N Instrucciones de montaje

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH THE ILLUSTRATIONS.

PLEASE SAVE THESE INSTRUCTIONS

Lo-Watt Manivent AC

Whole-house extract system

Installation and Wiring Instructions

MANI3000N

IP22

Installation and Wiring Instructions for the ManiVent MANI3000N.

IMPORTANT:

READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION

SAFETY AND GUIDANCE NOTES

1. DO NOT install this product in areas where the following may be present or occur:

1.1. Excessive oil or a grease laden atmosphere.

1.2. Corrosive or flammable gases, liquids or vapours.

1.3. Ambient temperatures higher than 40°C or less than -5°C.

1.4. Possible obstructions which would hinder access or removal of the Fan.

2. All wiring to be in accordance with the current I.E.E. Regulations, or the appropriate standards of your country and

MUST be installed by a suitably qualified person.

3. The fan should be provided with a 3A fused, isolator switch capable of disconnecting all poles, having a contact

separation of at least 3mm.

4. Ensure that the mains supply (voltage, frequency, and phase) complies with the fan’s rating label.

6. When the fan extracts air from a room containing an open flue of a gas or fuel burning appliance, precautions

must be taken to avoid the back-flow of gases into the room.

7. The fan should not be used where it is liable to be subjected to direct water spray.

8. The fan should be mounted at the highest point in the system to protect it from condensation build up.

9. This fan should be vented to the outdoors.

10. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

11. Children should be supervised to ensure that they do not play with the appliance.

12. PLEASE NOTE: Some older fluorescent and low energy lighting products can interfere with other

electronic/timing circuits. For reliable operation of timers use post 2000 low energy bulbs or tungsten filament bulbs

in the room lighting circuit.

TYPICAL INSTALLATION

INTRODUCTORY NOTES

The MANI3000N is an M.E.V (Mechanical Extract Ventilation) unit designed for simultaneous extract ventilation of

multiple areas such as bathrooms, kitchens and toilets. The MANI3000N employs a highly efficient backward curved

centrifugal motor impeller set and is designed for continuous 24-hour use.

The MANI3000N has 3 speed settings, High, Medium and Low, these are not adjustable.

The speeds are selectable via the 2 LS inputs.

The product will run at Normal speed unless the input from an accessory calls for a change to Boost or Purge speed.

For the MANI3000A the Boost setting is activated using a switched live supply (LS input). The other remaining LS

input can be used to switch the unit to Purge speed.

B. SITING

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient exhaust air temperatures higher than 40°C or less than –5°C.

•Relative humidity above 90%

• Possible obstructions which would hinder the access or removal of the Unit.

•Sudden ductwork bends or transformations close to the Unit.

The MANI3000N can be mounted in 3 orientations for convenient installation in roof voids with a height ≥250mm.

a). Base mounted Installation with ducting radiating out horizontally.

b). Vertically mounted Installation with the exhaust spigot at top. The electrical connections must come out of the

bottom of the unit in order to maintain the water ingress protection rating.

c). Ceiling mounted Installation.

See the dimensional details below for the mounting hole positions.

-Spigot diameters are 125mm

C. INSTALLATION

To reduce the system resistance in your duct system, and therefore lower the speed, power consumption and noise

of the fan, please follow these instructions:

•Keep the length of duct runs to a minimum, particularly the exhaust duct run.

•Use larger diameter ducting rather than smaller.

•If you need to use flexible ducting, make sure that it is fully extended and not crushed, sagging or torn.

•Try to minimise the use of dampers by having similar length duct runs to the inlets.

•The bend radius, (measured to the inside of the bend), should be at least 1x the duct diameter. The larger,

the better.

•Avoid having any bends, filters or other obstructions within 250mm of the fan inlets and outlet.

1. Position the MANI3000N, taking into consideration the position of the rooms to be ventilated, the exhaust

position, the drainage position and the electrical services. Ensure there is adequate access for installation

and maintenance. Securely mount the MANI3000N through the mounting brackets on the casing using the

appropriate anti-vibration mounts, screws, washers, rubber bushes etc.

2. Ducting passing through an unheated space should be insulated.

The MANI3000N can be connected to either Ø125mm or Ø100mm ducting. Remove the blanking caps to

connect Ø125mm ducting. To connect Ø100mm ducting, peel out the centre of the cap with a screwdriver as

indicated on the cap and leave the cap surround in position.

Please note that the exhaust duct must always be Ø125mm ducting.

D. WIRING

WARNING: THE MANI3000N AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

THE MANI3000N UNIT MUST BE EARTHED.

Access to the MANI3000N connection terminals is under the top cover which is retained by four screws. Ensure that

the mains supply voltage, frequency, number of phases and power rating comply with the details on the rating label

positioned under the top cover.

All wiring must be in accordance with local and/or national electrical codes as applicable or the appropriate standard

in your country (BS7671 in the UK). The MANI3000N must be supplied through a double-pole isolating switch, having

a contact separation of not less than 3mm. Cable clamps are provided for use with the cable or flex on entry into the

MANI3000N.

The MANI3000N has three speed settings. Select the required speed and wire as indicated in Figure 1.

Alternatively the MANI3000N may be wired in a number of different ways to achieve optimum ventilation control.

Figure 2 shows a wiring diagram to provide 3-speeds selectable by a remote switch.

Figure 3 shows a wiring diagram for automatic switching from medium to high speed using an external sensor.

1. Connect mains supply as (Fig. 1,2 or 3 below)

2. Check that all connections have been made correctly. Ensure that all terminal screws and cable clamps are

securely fastened.

3. The cable entry must be made using a suitable grommet or cable gland.

4. Replace cover using the 4 screws provided. Switch the mains supply on and check the system is operating

correctly.

Fig.1.

Permanent wiring for fixed speed

Fig.2.

Wiring for 3 speeds selectable by external switch

Fig.3.

Wiring for automatic switching from medium to high speed utilising an external sensor.

E. OVER-HEATING PROTECTION

The MANI3000N motor is fitted with Standard Thermal Overload Protection. This will automatically switch the fan Off

in the event of a fault condition.

If this occurs isolate the MANI3000N, check for and remove any obstruction, leave for a short time for the motor to

cool before reconnecting. If this recurs, Isolate the MANI3000N and call a service engineer.

F. COMMISSIONING

Select the speed needed based on the size and ventilation requirements of the dwelling.

G. SERVICING AND MAINTENANCE.

This product contains a self-cleaning backward curved impeller that requires no servicing.

The fan has sealed for life bearings, which do not require lubrication.

H. PRODUCT FICHE

This product contains a self-cleaning backward curved impeller that requires no servicing.

Name: Manrose Manrose

Model ID (Stock Ref.) : MANI3000N MANI3000N

SEC Class B E

SEC Val e ('Average') -26.25 -18.87

SEC Val e ('Warm') -10.75 -6.85

SEC Val e ('Cold') -53.31 -39.84

Label Req ired? (Yes/No=O t of scope) Yes Yes

Declared as: RVU or NRVU/UVU or BVU RVU RVU

Speed Drive M lti-Speed M lti-Speed

Type HRS (Rec perative, Regenerative, None) None None

Thermal Eff: [ (%), NA(if none)] N/A N/A

Max. Flow Rate (m3/h) 396.00 396.00

Max. Power Inp t (W): (@Max.Flow Rate) 63.30 63.30

LWA: So nd Power Level (dB) 51.53 51.53

Ref. Flow Rate (m3/s) 0.08 0.08

Ref. Press re Diff. (Pa) TBC TBC

SPI [W/(m3/h)] 0.12 0.12

Control Factor & Control Typology: (CTRL/ Typology)

Control Factor; CTRL 0.65 0.85

Control Typology

Local Demand

Control

Central Demand

Control

Declared: -Max Internal & External Leakage Rates(%) for BVUs or

carry over (for regenerative heat exchangers only),

-&Ext. Leakage Rates (%) for D cted UVUs;

<5% Internal, <5%

External

<5% Internal, <5%

External

Mixing Rate of Non-D cted BVUs not intended to be eq ipped

with one d ct connection on either s pply or extract air side; N/A N/A

Position and description of vis al filter warning for RVUs

intended for se with filters, incl ding text pointing o t the

importance of reg lar filter changes for performance and energy

efficiency of the nit

N/A N/A

For UVUs (Instr ctions Install Reg lated S pply/Extract Grilles

Façade) In F&W In F&W

Internet Address (for Disassembly Instr ctions) www.manrose.co. k www.manrose.co. k

Sensitivity p. Variation@+20/-20 Pa: (for Non-D cted V s) N/A N/A

Air Tightness-ID/OD-(m3/h) (for Non-D cted V s) N/A N/A

Ann al Electricity Cons mption: AEC (kWh/a) 0.82 1.23

Ann al Heating Saved: AHS (kWh/a)

AHS: Average 28.30 21.93

AHS: Warm 12.80 9.92

AHS: Cold 55.36 42.90

476875A 0817

Tabla de contenidos

Otros manuales de Admirador de Manrose

Manrose

Manrose LED Series Guía de instalación

Manrose

Manrose Aria 250 Motor Manual de usuario

Manrose

Manrose CQF100 Manual de usuario

Manrose

Manrose FAN7183 Manual de usuario

Manrose

Manrose Classic Series Manual de usuario

Manrose

Manrose FAN7187 Manual de usuario

Manrose

Manrose FAN5371 Manual de usuario

Manrose

Manrose FAN7191 Manual de usuario

Manrose

Manrose MRUF150WH Instrucciones de montaje

Manrose

Manrose Classic Series Manual de usuario

Manrose

Manrose FAN0616 Manual de usuario

Manrose

Manrose FAN7500 Manual de usuario

Manrose

Manrose FAN7180 Manual de usuario

Manrose

Manrose FAN2303 Manual de usuario

Manrose

Manrose LED Series Manual de usuario

Manrose

Manrose EXTRACT-A-LITE Manual de servicio

Manrose

Manrose FAN0085 Manual de usuario

Manrose

Manrose FAN0148 Manual de usuario

Manrose

Manrose CRA100T Manual de usuario

Manrose

Manrose VIVO FAN7291 Manual de usuario

Manrose

Manrose SLIM F100 Manual de usuario

Manrose

Manrose M200P Manual de usuario

Manrose

Manrose intellivent 2.0 Manual de usuario

Manrose

Manrose CRA100HT&T Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje