Manhattan 158039 Manual de usuario

ULTRA

ATA/133

CONTROLLER

PCI CARD

USER

MANUAL

Model 158039

MAN-158039-UM-0508-02

Thank you for purchasing this MANHATTAN

Ultra ATA/133 Controller

PCI Card, Model 158039.

Compatible with IDE and ATAPI drives — including CD, DVD and HDD —

its two channels supports up to four devices with full-speed burst transfers,

and it supports data transfer rates of up to 133 MBps and drives above 137

GB.

Using 48-bit LBA (logical block addressing), this card breaks the size limit

of 137 GB hard drives to support larger storage devices, and compliance

with PCI Specication, revision 2.2 ensures that most desktop computers

and connected IDE/ATAPI devices can operate at peak performance.

The easy-to-follow instructions in this manual help make installation of

the card quick and simple, so you’ll also soon be enjoying the benets

of these additional features:

• Regular and low-prole slots

• Plug and Play installation — Windows compatible

• Lifetime Warranty

System Requirements

• Windows 2000/XP/Vista (Server 2003 users can follow the procedures

for Windows 2000/XP throughout this manual)

• Available PCI card slot

• CD-ROM drive

Package Contents

• Ultra ATA/133 Controller PCI Card

• Regular and low-prole brackets

• User manual and driver CD

HARDWARE INSTALLATION

1. Turn off your computer.

2. Unplug the power cord and remove your computer’s cover.

3. Remove the slot bracket from an available PCI slot.

4. To install the card, carefully align the card’s bus connector with the

selected PCI slot on the motherboard. Push the board down rmly.

5. Replace the slot bracket’s holding screw to secure the card.

6. Replace the cover, reconnect the power cord and turn the power on.

SOFTWARE INSTALLATION

With Initial Installation of Windows 2000/XP

Follow this procedure for a new installation of Windows 2000/XP (or

2003 Server) if you boot from a device attached to the Ultra ATA/133

Controller PCI Card. IMPORTANT: With Windows 2000, rst edit the

txtsetup.oem le on the driver installation disk by deleting the line from

the [Cong.PnP680] section that reads:

value = Parameters\PnpInterface, “5”, REG_DWORD, 1.

1. Insert your Windows installation CD into the CD/DVD-ROM drive (or

use the Windows 2000 boot diskette #1 and a oppy drive if your

system can’t boot from the CD).

2. Press “F6” for third-party SCSI or driver installation at the beginning

of text mode installation. Press “s” when the prompt on the Setup

screen asks if you want to specify an additional device; then insert the

driver CD and press “Enter.” On the subsequent menu that displays,

select the controller installation process that corresponds to the version

of Windows being installed; then press “Enter.”

3. When prompted to continue with text mode setup, press “Enter” again.

4. Follow the on-screen setup instructions to select the partition and le

system.

5. After Setup examines your disks, it will copy les from the CD to the

hard drive selected above and restart the system. After restarting, the

setup process will resume and nish the installation.

6. Once the operating system installation has completed, you can follow

the instructions in Verifying Controller Installation to conrm that the

controller has been installed correctly.

With Initial Installation of Windows Vista

1. Insert your Windows Vista DVD into the DVD-ROM drive and insert the

Ultra ATA/133 Controller PCI Card driver CD in the CD_ROM drive.

2. When Vista starts from the DVD, change the displayed language and

keyboard preferences as needed and click “Next”; on the subsequent

screen, click “Install now.”

3. Enter your product key and click “Next.”

4. Select the option “I accept the license terms” and click “Next.”

5. Select the option “Custom (advanced).”

6. Click the icon labeled “Load Driver”; in the subsequent “Load Driver”

pop-up window, click “OK.”

7. When the “Select the driver to be installed” screen displays, select

“ITE ATA/133 Controller” and click “Next.” Windows will now load the

driver.

8. The newly installed drive should now be displayed. Click “Drive options

(advanced).”

9. Highlight the unallocated space of the installed drive and click “New.”

In the Size box that displays, specify the size of the partition to be

created to contain the Vista OS installation; then click “Apply.”

10. Select the newly created partition and click “Next.”

11. Follow the on-screen prompts to complete the installation of Vista.

Once the operating system installation is complete, you can follow the

instructions in Verifying Controller Installation to conrm that the

controller has been installed correctly.

With an Existing Installation of Windows 2000/XP

1. As Windows boots, a “Found New Hardware Wizard” message

displays. Click “Next.”

2. Select “Search for a suitable driver for my device (Recommended)”

and click “Next.”

3. Insert the driver CD and click “Next.”

4. When the wizard says it’s found a driver for the device, click “Next.”

5. If the message “Digital Signature Not Found” displays, click “Yes” to

continue installing the driver.

6. The wizard will now copy the required les to the system and start the

driver. After starting the driver, the wizard will display a completion

message. Click “Finish” to exit the wizard.

7. Follow the instructions in Verifying Controller Installation to conrm

that the controller has been installed correctly.

With an Existing Installation of Windows Vista

1. As Windows boots, a “Found New Hardware Wizard” message

displays. Select “Locate and install driver software (recommended).”

If the prompt “User Account Control” displays, click “Continue.”

2. On the subsequent screen, select “Don’t search online.”

3. Insert the driver CD and click “Next.”

4. Windows will now begin to install the driver software. If the message

“Windows can’t verify the publisher of this driver software” displays,

click “Install this driver software anyway.”

5. Once the installation is complete, you can follow the instructions in

Verifying Controller Installation to conrm that the controller has been

installed correctly.

Updating the Driver on Windows 2000

1. Right-click on My Computer and go to Properties. In System Properties,

go to Hardware, then Device Manager. Select “SCSI and RAID

Controllers”; then right-click “ITE ATA/133 Controller” and go to

Properties (on the context menu).

2. Go to Driver and click “Update Driver.” Select “Display a list of the

known drivers for this device so that I can choose a specic driver.”

Insert the driver CD, then click “Next.”

3. Click “Have Disk.” When the “Install from Disk” prompt displays, ensure

that the correct drive is specied and click “OK.”

4. Click “Next” until the installation process begins. If a warning about an

unsigned driver displays, click “Yes” to continue.

5. When installation is complete, a reboot prompt may display. Click “Yes.”

6. Follow the instructions in Verifying Controller Installation to conrm

that the procedure was successful.

Updating the Driver on Windows XP

1. Right-click on My Computer and go to Properties. In System Properties,

go to Hardware, then Device Manager. Select “SCSI and RAID

Controllers”; then right-click “ITE ATA/133 Controller” and go to

Properties (on the context menu).

2. Go to Driver and click “Update Driver.”

3. Select “Install from a list or specic location (Advanced)”; click “Next.”

4. Select both “Search for the best driver in these locations” and “Search

removable media (oppy, CD-ROM...)”; click “Next.”

5. As the installation proceeds, a warning about a “non-logo” (uncertied)

driver may display; click “Continue Anyway.”

6. When installation is complete, a reboot prompt may display. Click “Yes.”

7. Follow the instructions in Verifying Controller Installation to conrm

that the procedure was successful.

Updating the Driver on Windows Vista

1. Click the Start icon, then right-click on Computer and go to Manage (on

the context menu). If a “User Account Control” prompt displays, click

“Continue.”

2. Go to Device Manager in the left-hand panel, then double-click on

Storage Controllers in the right-hand panel.

3. In Storage Controllers, right-click “ITE ATA/133 Controller” and go to

Properties (on the context menu).

4. Go to Driver and click “Update Driver….”

5. Select “Browse my computer for driver software.”

6. Select “Let me pick from a list of device drivers on my computer.”

7. Click “Have Disk….”

8. With “Install From Disk” displayed, either click “Browse” or specify the

path to where the updated driver package resides on the system (for

example, E:\); then click “OK.”

9. Click “Next.” Windows will begin installing the updated driver software. If

a message displays that Windows can’t verify the publisher of the driver

software, select “Install this driver software anyway.”

10. When installation is complete, a reboot prompt may display. Click “Yes.”

11. Follow the instructions in Verifying Controller Installation to conrm

that the procedure was successful.

Verifying Controller Installation for Windows 2000/XP

1. Right-click on My Computer and go to Properties, then Hardware, then

Device Manager.

2. Double-click “SCSI and RAID Controllers.” If no yellow exclamation

point (!) or question mark (?) appears to the left of “ITE ATA/133

Controller,” then the driver has started properly.

3. To view information about the devices attached to the controller, right-

click “ITE ATA/133 Controller” and go to Properties (on the context

menu). Then go to Device Info to see the information.

Verifying Controller Installation for Windows Vista

1. Click the Start icon, then right-click on Computer and go to Manage (on

the context menu). If a “User Account Control” prompt displays, click

“Continue.”

2. Go to Device Manager in the left-hand panel, then double-click on

Storage Controllers in the right-hand panel. If no yellow exclamation

point (!) or question mark (?) appears to the left of “ITE ATA/133

Controller,” then the driver has started properly.

3. To view information about the devices attached to the controller, right-

click “ITE ATA/133 Controller” and go to Properties (on the context

menu). Then go to Device Info to see the information.

SPECIFICATIONS

Standards and Certications

• PCI Specication, revision 2.2

• ATA 133 Standard

General

• 32-bit, 33 MHz fully compliant PCI host

• Support of ATAPI devices

• 48-bit LBA supports HDD larger than 137 GB

• Supports two independent ATA-133 channels

• ITE chipset

All products mentioned are trademarks or registered trademarks of their respective owners.

www.manhattan-products.com

MANHATTAN®offers a complete line

of PC Components, Peripherals, Cables and Accessories.

Ask your local computer dealer for more information

or visit us online at

Tabla de contenidos

Otros manuales de Tarjeta PCI de Manhattan

Manhattan

Manhattan 151375 Manual de usuario

Manhattan

Manhattan 160452 Manual de usuario

Manhattan

Manhattan 150965 Manual de usuario

Manhattan

Manhattan 158213 Manual de usuario

Manhattan

Manhattan 160414 Manual de usuario

Manhattan

Manhattan 150682 Manual de usuario

Manhattan

Manhattan 158237 Manual de usuario

Manhattan

Manhattan 167901 Manual de usuario

Manhattan

Manhattan 151757 Manual de usuario

Manhattan

Manhattan 167901 Manual de usuario

Manhattan

Manhattan 158220 Manual de usuario

Manhattan

Manhattan 150965 Manual de usuario

Manhattan

Manhattan 176767 Manual de usuario

Manhattan

Manhattan 162579 Manual de usuario

Manhattan

Manhattan 165495 Manual de usuario

Manhattan

Manhattan 158183 Manual de usuario

Manhattan

Manhattan 158176 Manual de usuario

Manhattan

Manhattan 176781 Manual de usuario

Manhattan

Manhattan 158299 Manual de usuario

Manhattan

Manhattan 150040 Manual de usuario

Manhattan

Manhattan 175586 Manual de usuario

Manhattan

Manhattan 158220 Manual de usuario

Manhattan

Manhattan 158206 Manual de usuario

Manhattan

Manhattan 515245 Manual de usuario

Manuales populares de Tarjeta PCI de otras marcas

ERMA

ERMA SSI 1417 Manual de usuario

SIIG

SIIG CyberSerial Dual PCI Instrucciones de montaje

Moxa Technologies

Moxa Technologies CP-102E Manual de usuario

I-Bus

I-Bus IBC2602 Manual de usuario

Exsys

Exsys EX-60102 Manual de usuario

Chelsio Communications

Chelsio Communications T5 Series Manual de usuario

Conrad Electronic

Conrad Electronic 97 46 71 Manual de usuario

Micro Innovations

Micro Innovations USB650A Manual de usuario

KTI Networks

KTI Networks KF-310 Manual de usuario

Asus

Asus SpaceLink WL230 Manual de usuario

SIIG

SIIG SC2475 Manual de usuario

TRENDnet

TRENDnet TEW-703PI Manual de usuario

Belkin

Belkin F5D7000F Manual de usuario

Pericom

Pericom PI7C7100 Manual de usuario

ADLINK Technology

ADLINK Technology cPCI-3548 Manual de usuario

Digium

Digium TE200 Series Manual de usuario

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manual de usuario

Western Digital

Western Digital FireWire PCI Adapter Manual de usuario