Makita 6912D Manual
6912D
12mm Cordless ratchet wrench
This product was developed to make temporary
fastening of bolts and nuts easier for constructing
prefabricated houses.
It can also be used as an ordinary ratchet wrench to
finally tighten the bolts and nuts by swiveling its
handle clockwise with the ratchet mechanism.
The model 6912DW is made up of
6912D (Makita 12mm battery powered ratchet wrench)
DC7000 (Boosting charger)
The model 6912D does not include batteries.
Motor DC 7.2 magnet motor
No load speed(R.P.M.) 270
The size of the eyelet part of the wrench 21 mm in thickness with two eyelet parts together
Bolt size suitable for the model 1/25 inches
Temporary fastening with the torque by
Net weight(Kg) 20 kg-cm
0.85
Socket adapter --- One piece.
Battery model 7000
The standard equipment for the tools shown may differ form country to country
23
322
22
Specifications
Standard equipment
Optional accessories
CONCEPTION AND MAIN APPLICATIONS
Models No.
New Tool
TECHNICAL INFORMATION
Description
1) Replacement of the clutch
(1) Loosen the hexagon socket head cap screws 1(M4x18) and 2(M4x25) with hexagon socket screw keys. and
dismantle the sub-housing R and L, and housing R and L. (See the fig.1.)
Fig.1
(1)Hexagon socket head cap screw
(2)Hexagon socket head cap screw
Gripping position
(3)Sub-housing L
(4)Sub-housing R
(5)Housing L
(6)Housing R
Repair
(2) The parts from7 to 14 can be easily dismounted after the sub-housing R and L are taken off. Remove the housing
R and then remove the parts from 15 to 29 out of the housing L. (Care must be taken not to misplace 27 the
compression spring 6 in removing the parts.) (See fig.2.)
(3) 18 the spindle, 19 steel ball 3.5 20 compression spring 2.4 and 21 complete clutch cam assembly are the clutch
related parts. Other parts can be manually dismounted. (See the fig.2.)
(4) Remove 21 the complete clutch cam assembly from 18 the spindle.(Be careful not to scatter19 steel balls around
in removing the 21 complete clutch cam assembly as the 19 steel balls 3.5 are pressed against the 21 complete
clutch cam assembly with the 21 compression spring 2.4.) See the fig. 2.
(5) Replace the 20 Compression spring 2.4 and 21 complete clutch cam assembly together in replacing the clutch
(7)
(8)
(9)
(10)
(11)
(25) (28)
(27)
(26) (29)
(24)
(23)
(22)
(21)
(20)
(19)
(18)
(17)
(16)
(15)
(14)
(13)
(12)
(7)Torsion spring (8)Spring type catch (9)Ratchet holder (10)Socket 21 (11)Pin 4
(12)Ratchet pawl (13)Torsion spring 7 (14)Sleeve 4 (15)Collar (16)Needle bearing 1015
(17)Flat washer (18)Spindle (19)Steel ball 3.5 (20)Compression spring 24 (21)Complete clutch cam
(22)Spur gear 16 (23)Internal spur gear 49 (24)Flat washer (25)DC motor (26)Switch
(27)Compression spring 6 (28)Switch lever (29)Battery holder
Fig.2
Assembling
(1) Assemble the parts from 18 to 21.
Put the 19 steel balls 3.5 with the 20 compression spring 2.4 installed between the balls into the 3.6 mm
diameter bore at the end of the 18 spindle. Insert the steel balls aligned with the groove in the complete clutch
cam assembly by holding the 19 steel balls down. (See the fig. 3.)
(2) Mount the parts from (16) to (29) in the (5) housing L.
Fit the 28 switch lever in together with the 26 switch and also the 27 compression spring 6. Insert the 17 flat
washer 10 and 16 needle bearing 1015 in this order into the 18 spindle assembled in the above 1. Insert 3 pieces
of the 22 spur gears 16 into the 21 complete clutch cam assembly and engage the gears with the 23 internal spur
gear 49. Mount the 24 flat washer 15 at the same time.
(In assembling the internal spur gear, engage one of its slots against the rotation lock. Mount the 16 needle
bearing1015 by bringing it toward the left end as shown in the fig. 4.)(See the figs. 2, 3, & 4.)
(3) Assemble the 6 housing R and sub-housing R. (Confirm the 18 spindle can rotate smoothly, and that there is a
play in the axial direction after the housing and sub-housing are assembled.)
Hold it down Ditch
Hold it down
Grease
(18)Spring
(21)Complete clutch cam assembly
Fig.3
(5)Housing L
Place the needle bearing side on the motor side.
Bring the 16 needle bearing 1015 against this face.
(23)Internal spur gear 49 locking part
(28)Put the 28 switch lever through
Fig.4
(4) Turn the wrench upside down, and assemble the parts from 7 to 15.
Fig. 5
Mount the 1 hexagon socket head cap screw (M4x18) in the 4 sub-housing R, insert the 14 sleeve 4, and assemble
the 12 ratchet pawl and 13 torsion spring 7 as shown in the fig. 5.(Be careful not to catch the 14 torsion spring 7
between the 14 sleeve and 4 sub-housing in the above assembling process.)
Assemble the parts from 7 to 11 as shown in the fig.5, and mount the assembled one to the main body. (It is easier to
assemble the parts with the 15 collar positioned to the other side to the 12 ratchet pawl.)
(5) Mount the (3) sub-housing L and tighten the screws.(Install the spring washer on the nut for mounting the (1)
hexagon socket head cap screw (M4x18).)
(4)Sub-housing R
(12)Ratchet pawl
(5)Housing L
(13)Torsion spring
(14)Sleeve 4
(15)Collar
Assemble the parts from 7 to 10
by holding them down.
Assemble the (10) socket 21
by holding it down.
(10)Socket 21
(11)Pin 4
(7)Torsion spring5
(8)Spring type catch
(9)Ratchet holder
One with the longer
ground part.
Mount it on the main body.
One with the smaller diameter.
Fig.6
Otros manuales para 6912D
1
Otros manuales de Herramientas eléctricas de Makita
Makita
Makita UX01G Manual de usuario
Makita
Makita HM1202 Manual de usuario
Makita
Makita DTWA070 Manual de usuario
Makita
Makita DCG180RMB Manual de usuario
Makita
Makita DTM41 Manual de usuario
Makita
Makita HR2650 Manual de usuario
Makita
Makita DTW181 Manual de usuario
Makita
Makita DTM41 Manual de usuario
Makita
Makita JN3201 Manual de usuario
Makita
Makita DTW285 Manual de usuario
Makita
Makita BTW4 Manual de usuario
Makita
Makita DVR340 Manual de usuario
Makita
Makita DTS130 Manual de usuario
Makita
Makita HM1242C Manual de usuario
Makita
Makita HR2652 Manual de usuario
Makita
Makita BTS130 Manual de usuario
Makita
Makita RP1100 Manual de usuario
Makita
Makita DJS161 Manual de usuario
Makita
Makita DUP361 Manual de usuario
Makita
Makita BTW110 Manual
