Makita 9029 Manual

9029

CONCEPTION AND MAIN APPLICATIONS

Specifications

Continuous Rating (W)

Voltage (V) Current (A) Cycle (Hz) Input Output Max. Output(W)

100 15.0 50/60

50/60

1,430

1,650

1,430

600

115 15.0 800 2,600

3,500

2,600

200 10.5 1,200

220 9.6 2,000

2,000

1,200

3,500

230 9.2

240 8.8

Standard equipment

Lock Nut Wrench 35, Grip 35

Optional accessories

Dust Collecting Wheel Guard, Inner Flange 47 (DIN spec. Spur Flange),

Depressed Center Wheel 24P, 36P, Inner Flange 78 (For cut-off wheel),

Outer flange 78 (For cut-off wheel), Loop Handle, Wire Cup Brush 110

Features and benefits

Long-expected disc grinders are offered by Makita now. Their

power, maneuverability and dust-proof mechanism are

outstanding. Try them! They are ideal for both grinding and cut-

off jobs.

Model 9029S has soft start feature.

(Note)

Model 9029S is offered to 200V-240V areas and countries only

230mm (9") Disc Grinder

1. New type motor (powerful and durable motor) is employed to prevent burnout.

2. Excellent dust-proof mechanism (dust-proof ball bearings, dust-proof labyrinth, etc. are built in the tool)

assures long life of the tool.

3. Large trigger switch with lock-on/off lever for increased maneuverability.

4. Low profile gear housing for easy operation.

5. Switch handle can be rotated to either 90ÅKleft or right to fit your work needs.

6. Side grip can be installed in any three positions on the sides of the tool.

7. Automatic cut-out carbon brush is equipped.

8. Double insulated for operator safety.

Models No.

Description

New Tool

TECHNICAL INFORMATION

No load Speed: 6,600 R/min.

Capacities

Depressed Center Wheel: 230 mm (9")

Wire Cup Brush : 110 mm (4-3/8")

Net weight: 5.5 kg (12.1 lbs)

462mm

244mm

144mm

Large size shaft lock

Increase maneuverability Powerful and durable motor having

property for preventing burnout

Dust-proof cover can be

installed optionally. (Parts used for repairing at field)

Repairing and replacing can be facilitated in low cost at field.

PAT.P

Durability at overload is improved and burnout of

armature due to commutator insulation failure is reduced.

Inlet port is directed facing rear side

to reduce dust absorbing.

Dust-proof

ball bearing Dust-proof

labyrinth

structure ÉJ Current is automatically interrupted to protect

armature when carbon brushes are worn. Also

carbon brush is large sized to allow long service life

(comparing with model 9609HB) and for easy

replacing (comparing with model 9629).

Easy for gripping.

Prevent tool from dropping during

cutting off work.

Side grip can be installed in any three

positions on right and left sides of the

tool.

Dust-proof

ball bearing

Tool rest (Bumper made of rubber) Stream lined design flowing along

handle from front to back

Handle allowing rotation to either

90 Kleft or right to fit work. PAT.P

Tool rest allows stabled tool position when

turned over for replacing wheel.

Fitting your work needs during

cutting off

Low profile gear housing

Dust-proof ball bearing

Loop handle is

provided

optionally.

Large trigger switch

Wheel replacing is easy.

Super flange can be installed. PAT.P

Safety lock-on/off mechanism is provided.

Four fingers can touch the switch to increase

maneuverability.

PAT.P: Patent pending

New 94 type motor

Adoption of support

Large size commutator ceramic ball adopted

Cut-out carbon brush

New designed side grip

(1) Replacing of armature

i) Remove wheel, wheel cover, and bearing box respectively.

(Refer to owner's manual for wheel cover removing method.)

ii) Remove gear housing and armature as one body after carbon brush is removed.

iii) Unscrew bearing retainer attaching screw (Mounted from gear housing side with M5 x 10 and M5 x 20.) and remove

armature.

iv) Be sure to mate bearing retainer guide portion with projected portion of bearing retainer before inserting and tighten with

hex socket head bolt when armature is assembled to gear housing. Adhesive is applied to hex socket head bolt then be

sure replace with new one once the bolt is removed.

Hex socket head bolt

M5 x 20

Hex socket head bolt

M5 x 10

Repair

(2) Replacing spiral bevel gear 12

(1) Replace spiral bevel gear 12 after removing armature from gear housing according to armature replacing method.

Spiral bevel gear can not be replaced when armature is assembled in gear housing.

(3) Malfunction of shaft lock portion

When activation of shaft lock portion becomes inactive du e to

contaminated dust.

i) Dismount pin cap using minus driver or etc. and remove dust

inside shaft lock portion.

ii) Make pin cap mate with hole and depress it to mount on pin

again.

(4) Malfunction of handle turning

When handle turning is prevented from contaminated dust.

i) Remove handle fixing and mounting screws, dismount handle L

and R, and remove dust in motor housing and rotating portion of

handle L and R to clean.

ii) Tighten handle mounting screw M4 x 25 with tightening torque

10~15kg-cm (0.7~1.1ft-lbs) and handle fixing screw M6 x 85

with 20~30kg-cm (1.4~2.2ft-lbs) respectively.

(5) Reference information: Angle adjusting for gear housing

Gear housing angle can be changed in four position at

90°Kinterval.

i) Remove wheel and wheel cover.

ii) Remove carbon brush then dismount gear housing and arm ature

without separating them from motor housing.

iii) After cutting off baffle plate partially at two portio ns where

interference is occurred with projected portions of motor

housing using knife then mate gear housing and motor housing

at required position to attach.

iv) Mount gear housing at required position.

(Note: Do not let users make gear angle adjustment.)

Pin cap

Minus

driver

turning portion

Make mate position

Baffle plate

Cutting off

(1) 9029

(2) 9029S

(Note) Condenser is not used in some areas.

Wiring Diagram

(Note) Condenser is not used in some areas.

Switch

Power Supply

Cord

Resistor

Insulated

terminal

Field Purple

Purple

Orange

Black

Insulated terminal

Power Supply

Cord

Capasitor

Insulated terminal Insulated terminal

Field Purple

Purple

Orange

Black

Capasitor

Tabla de contenidos

Otros manuales de Amoladora de Makita

Makita

Makita GA7021 Manual de usuario

Makita

Makita GA4540R Manual de usuario

Makita

Makita GA7010C Manual de usuario

Makita

Makita GA035G Manual de usuario

Makita

Makita GA030G Manual de usuario

Makita

Makita GA024G Manual de usuario

Makita

Makita 9565CR Manual de usuario

Makita

Makita DGA406 Manual de usuario

Makita

Makita 9527PB Guía de inicio rápido

Makita

Makita DGA901T2U2 Manual de usuario

Makita

Makita GA4552 Manual de usuario

Makita

Makita GA039G Manual de usuario

Makita

Makita M0901 Manual de usuario

Makita

Makita DGA417 Instrucciones de funcionamiento

Makita

Makita GA4030R Manual de usuario

Makita

Makita GA037G Manual de usuario

Makita

Makita GA037G Manual de usuario

Makita

Makita GA042G Manual de usuario

Makita

Makita 9564CVL Manual de usuario

Makita

Makita 9560CV Manual de usuario

Makita

Makita GE0600 Manual de usuario

Makita

Makita GA4030R Manual de usuario

Makita

Makita GD0800C Manual de usuario

Makita

Makita DGA405 Manual de usuario

Manuales populares de Amoladora de otras marcas

Parkside

Parkside PWS 230 C3 Manual de usuario

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Manual técnico

PTA

PTA P1322 Manual de usuario

Crown

Crown CT13313 Manual de usuario

Parkside

Parkside 280250 Manual de usuario

Climax

Climax VM2150 Series Manual de usuario

Jet

Jet JPSG-618M1 Manual de servicio

DeWalt

DeWalt DWEN202 Manual de usuario

Grizzly

Grizzly G2790 Manual de usuario

Fein

Fein MSf843-1a Manual de usuario

Bosch

Bosch GWS 14,4 V PROFESSIONAL Manual de usuario

RAMSET

RAMSET CBAGR18 Manual de usuario

Bosch

Bosch 8-115 Z Manual de usuario

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Manual de usuario

MW TOOLS

MW TOOLS ME15W Manual de usuario

Caravaggi

Caravaggi SP 20 Instrucciones de funcionamiento

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Manual técnico

Metabo

Metabo WEF 9-125 Quick Manual de usuario