Makita XSH03 Manual de usuario

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

IMPORTANT: Read Before Using.

IMPORTANT: Lire avant usage.

IMPORTANTE: Leer antes de usar.

Cordless Circular Saw

Scie Circulaire sans Fil

Sierra Circular Inalámbrica

XSH03

015157

ENGLISH (Original instructions)

SPECIFICATIONS

Model XSH03

Blade diameter 165 mm (6-1/2")

at 0° 57 mm (2-1/4")

at 45° 41 mm (1-5/8")

Max. cutting depth

at 50° 37 mm (1-7/16")

No load speed (RPM) 5,000 /min

Overall length 350 mm (13-3/4")

Net weight 3.1 kg (6.8 lbs) 3.3 kg (7.3 lbs)

Rated voltage D.C. 18 V

Standard battery cartridge(s)

Warning: Use only the battery(ies) described. BL1815N / BL1820 BL1830 / BL1840 / BL1850

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

GEA006-2

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal safety

10. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

11. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your finger on the switch or energising power

tools that have the switch on invites accidents.

13. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

14. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

15.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts.

Loose clothes, jewellery

or long hair can be caught in moving parts.

16.

If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used.

Use of dust

collection can reduce dust-related hazards.

Power tool use and care

17. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

18. Do not use the power tool if the switch does

not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous

and must be repaired.

19. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

20. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

21.

Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use.

Many accidents are caused by

poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

Battery tool use and care

24. Recharge only with the charger specified by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire

when used with another battery pack.

25. Use power tools only with specifically

designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

26. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery

terminals together may cause burns or a fire.

27.

Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid

ejected from the battery may cause irritation or burns.

Service

28. Have your power tool serviced by a qualified

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

29. Follow instruction for lubricating and

changing accessories.

30. Keep handles dry, clean and free from oil and

grease.

GEB120-3

CORDLESS CIRCULAR SAW

SAFETY WARNINGS

Cutting procedures

DANGER: Keep hands away from cutting area

and the blade. Keep your second hand on

auxiliary handle, or motor housing.

If both hands

are holding the saw, they cannot be cut by the blade.

Do not reach underneath the workpiece.

The guard

cannot protect you from the blade below the workpiece.

3. Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the blade

teeth should be visible below the workpiece.

Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable platform.

It is important to support the work properly to minimize

body exposure, blade binding, or loss of control.

A typical illustration of proper hand support

and workpiece support.

000161

5. Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting tool may contact hidden

wiring. Contact with a "live" wire will also make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

6. When ripping, always use a rip fence or

straight edge guide. This improves the accuracy

of cut and reduces the chance of blade binding.

Always use blades with correct size and shape

(diamond versus round) of arbour holes.

Blades

that do not match the mounting hardware of the saw

will run eccentrically, causing loss of control.

8. Never use damaged or incorrect blade

washers or bolt. The blade washers and bolt

were specially designed for your saw, for

optimum performance and safety of operation.

Kickback causes and related warnings

−kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to

lift up and out of the workpiece toward the operator;

−when the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator;

−if the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into the

top surface of the wood causing the blade to climb out

of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below.

Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line

with the blade.

Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by the

operator, if proper precautions are taken.

10.

When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the

saw motionless in the material until the blade

comes to a complete stop. Never attempt to

remove the saw from the work or pull the saw

backward while the blade is in motion or kickback

may occur.

Investigate and take corrective actions to

eliminate the cause of blade binding.

11.

When restarting a saw in the workpiece, centre

the saw blade in the kerf and check that saw teeth

are not engaged into the material.

If saw blade is

binding, it may walk up or kickback from the

workpiece as the saw is restarted.

12.

Support large panels to minimise the risk of blade

pinching and kickback.

Large panels tend to sag

under their own weight. Supports must be placed

under the panel on both sides, near the line of cut

and near the edge of the panel.

To avoid kickback, do support

board or panel near the cut.

000192

Do not support board or

panel away from the cut.

014252

13.

Do not use dull or damaged blades.

Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

14. Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

15. Use extra caution when sawing into existing

walls or other blind areas. The protruding blade

may cut objects that can cause kickback.

16.

ALWAYS hold the tool firmly with both hands. NEVER

place your hand or fingers behind the saw.

If kickback

occurs, the saw could easily jump backwards over your

hand, leading to serious personal injury.

000160

17. Never force the saw. Push the saw forward at

a speed so that the blade cuts without

slowing. Forcing the saw can cause uneven cuts,

loss of accuracy, and possible kickback.

Lower guard function

18.

Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does

not move freely and close instantly. Never clamp or

tie the lower guard into the open position.

If saw is

accidentally dropped, lower guard may be bent. Raise

the lower guard with the retracting handle and make

sure it moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

19.

Check the operation of the lower guard spring. If

the guard and the spring are not operating

properly, they must be serviced before use.

Lower

guard may operate sluggishly due to damaged parts,

gummy deposits, or a build-up of debris.

20. Lower guard should be retracted manually

only for special cuts such as "plunge cuts"

and "compound cuts". Raise lower guard by

retracting handle and as soon as blade enters

the material, the lower guard must be released.

For all other sawing, the lower guard should

operate automatically.

21. Always observe that the lower guard is

covering the blade before placing saw down

on bench or floor. An unprotected, coasting

blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is

released.

22. To check lower guard, open lower guard by

hand, then release and watch guard closure.

Also check to see that retracting handle does

not touch tool housing. Leaving blade exposed

is VERY DANGEROUS and can lead to serious

personal injury.

Additional safety warnings

23. Intended use

This tool is intended to cut wood products

only. Accumulated sawdust on the lower guard

and hub from other materials may effect the

proper closure of the lower guard which could

lead to serious personal injury.

24. Use extra caution when cutting damp wood,

pressure treated lumber, or wood containing

knots. Maintain smooth advancement of tool

without decrease in blade speed to avoid

overheating the blade tips.

25. Do not attempt to remove cut material when

blade is moving. Wait until blade stops before

grasping cut material.Blades coast after turn off.

26. Avoid Cutting Nails. Inspect for and remove

all nails from lumber before cutting.

27.

Place the wider portion of the saw base on that

part of the workpiece which is solidly supported,

not on the section that will fall off when the cut is

made. As examples, Fig. 1 illustrates the RIGHT

way to cut off the end of a board, and Fig. 2 the

WRONG way. If the workpiece is short or small,

clamp it down. DO NOT TRY TO HOLD SHORT

PIECES BY HAND!

Fig. 1

014997

Fig. 2

000190

28. Before setting the tool down after completing

a cut, be sure that the lower guard has closed

and the blade has come to a complete stop.

29. Never attempt to saw with the circular saw

held upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

000029

30.

Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

31. Do not stop the blades by lateral pressure on

the saw blade.

32. Do not use any abrasive wheels.

33.

Only use the saw blade with the diameter that is

marked on the tool or specified in the manual.

Use of an incorrectly sized blade may affect the

proper guarding of the blade or guard operation

which could result in serious personal injury.

34. Keep blade sharp and clean. Gum and wood

pitch hardened on blades slows saw and

increases potential for kickback. Keep blade

clean by first removing it from tool, then cleaning

it with gum and pitch remover, hot water or

kerosene. Never use gasoline.

35. Wear a dust mask and hearing protection

when use the tool.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction manual

may cause serious personal injury.

USD301-5

Symbols

The followings show the symbols used for tool.

･volts

･direct current

･no load speed

･revolutions or reciprocation per minute

ENC007-8

IMPORTANT SAFETY

INSTRUCTIONS

FOR BATTERY CARTRIDGE

Before using battery cartridge, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical

attention right away. It may result in loss of

your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a

container with other metal objects such

as nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 ﾟC (122 ﾟF).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. Follow your local regulations relating to

disposal of battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before

completely discharged.

Always stop tool operation and charge the

battery cartridge when you notice less tool

power.

2. Never recharge a fully charged battery

cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10 ﾟC - 40 ﾟC (50 ﾟF - 104 ﾟF).

Let a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period

of time.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

015120

CAUTION:

• Always switch off the tool before installing or

removing of the battery cartridge.

•

Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge.

Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the

red indicator cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being

inserted correctly.

NOTE:

•

When the battery cartridge is not removed easily, push

it from the opposite side of the button and slide it.

Switch action

CAUTION:

•

Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the "OFF" position when released.

• Do not pull the switch trigger hard without pressing

the lock-off lever. This can cause switch breakage.

015107

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool,

press the lock-off lever and pull the switch trigger.

Release the switch trigger to stop.

WARNING:

• For your safety, this tool is equipped with lock-off

lever which prevents the tool from unintended

starting. NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the

lock-off lever. Return tool to a MAKITA service

center for proper repairs BEFORE further usage.

• NEVER tape down or defeat purpose and function

of lock-off lever.

Indicating remaining battery capacity

015143

When you turn the tool on, the battery indicator shows

the remaining battery capacity.

The remaining battery capacity is shown as the following table.

Battery indicator status

Remaining battery capacity

50% - 100%

20% - 50%

0% - 20%

Charge the battery

On Off Blinking

015146

1. Battery indicator

1. Switch trigger

2. Lock-off lever

1. Button

2. Red indicator

3. Battery cartridge

Automatic speed change function

015144

Mode indicator status Operation mode

High speed mode

High torque mode

015137

This tool has "high speed mode" and "high torque

mode". It automatically changes operation mode

depending on the work load. When mode indicator lights

up during operation, the tool is in high torque mode.

Tool / battery protection system

The tool is equipped with a tool/battery protection

system. This system automatically cuts off power to the

motor to extend tool and battery life.

The tool will automatically stop during operation if the

tool or battery are placed under one of the following

conditions. In some conditions, the indicator lights up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indications. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool

When the tool is overheated, the tool stops automatically

and the battery indicator shows following state. In this

situation, let the tool cool before turning the tool on again.

Battery indicator

Tool is overheated

On Off Blinking

015145

Releasing protection lock

When the protection system works repeatedly, the tool is

locked and the battery indicator shows the following state.

Battery indicator On Off Blinking

Protection lock works

015201

In this situation, the tool does not start even if turning

the tool off and on. To release the protection lock,

remove the battery, set it to the battery charger and wait

until the charging finishes.

Adjusting depth of cut

CAUTION:

• After adjusting the depth of cut, always tighten the

lever securely.

015198

Loosen the lever on the side of the rear handle and

move the base up or down. At the desired depth of cut,

secure the base by tightening the lever.

For cleaner, safer cuts, set cut depth so that no more

than one blade tooth projects below workpiece. Using

proper cut depth helps to reduce potential for dangerous

KICKBACKS which can cause personal injury.

Bevel cutting

015105

Loosen the front lever. Set for the desired angle (0° - 50°) by

tilting accordingly, then tighten the front lever securely.

1. Front lever

1. Lever

2. Depth guide

1. Mode indicator

0-45

0-50

015116

Use the 45° stopper when you do precise 45° angle

cutting. Turn the stopper counterclockwise fully for bevel

cut (0° - 45°) and turn it clockwise for 0° - 50° bevel cuts.

Sighting

015106

For straight cuts, align the 0° position on the front of the

base with your cutting line. For 45° bevel cuts, align the 45°

position with it. The position of the top guide is adjustable.

Lighting the lamp

CAUTION:

• Do not look in the lamp or see the source of lamp

directly.

015154

Only to turn on the lamp, pull the switch trigger without

pressing the lock-off lever. To turn on the lamp and run

the tool, press the lock-off lever and pull the switch

trigger with pressing the lock-off lever. The lamp keeps

on lighting while the switch trigger is being pulled. The

lamp goes out 10 -15 seconds after releasing the trigger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it

may lower the illumination.

•

Do not use gasoline, thinner or the like to clean the lens

of lamp. Using such substances will damage the lens.

Hook

CAUTION:

• Always remove the battery when hanging the tool

with the hook.

• Never hook the tool at high location or on

potentially unstable surface.

015119

The hook is convenient for hanging the tool temporarily.

To use the hook, simply turn it until it snaps into the

open position.

When not in use, always turn the hook until it snaps into

the closed position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Removing or installing saw blade

CAUTION:

• Be sure the blade is installed with teeth pointing

up at the front of the tool.

• Use only the Makita wrench to install or remove

the blade.

015108

To remove the blade, press the shaft lock so that the

blade cannot revolve and use the wrench to loosen the

hex bolt clockwise. Then remove the hex bolt, outer

flange and blade.

1. Hex wrench

2. Shaft lock

3. Tighten

4. Loosen

1. Hook

2. Close

3. Open

1. Lamp

1. Cutting line

(0 ﾟposition)

2. Cutting line

(45 ﾟposition)

3. Screw

1. Stopper

015109

To install the blade, follow the removal procedure in

reverse. BE SURE TO TIGHTEN THE HEX BOLT

COUNTERCLOCKWISE SECURELY.

When changing blade, make sure to also clean the upper and

lower blade guards of accumulated sawdust as discussed in

the Maintenance section. Such efforts do not replace the need

to check lower guard operation before each use.

011231

Mount the inner flange with its recessed side facing

outward onto the mounting shaft and then place saw

blade, outer flange and hex bolt.

BE SURE TO TIGHTEN THE HEX BOLT

COUNTERCLOCKWISE SECURELY.

Hex wrench storage

015110

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

Connecting a vacuum cleaner

(Optional accessory)

015195

015112

When you wish to perform clean cutting operation,

connect a Makita vacuum cleaner to your tool.

Replace the lever on the lower guard to the one supplied

with the dust nozzle. Install the dust nozzle on the tool using

the screw. Then connect a hose of the vacuum cleaner to

the dust nozzle as shown in the figure.

OPERATION

CAUTION:

• Be sure to move the tool forward in a straight line

gently. Forcing or twisting the tool will result in

overheating the motor and dangerous kickback,

possibly causing severe injury.

• Always use a front grip and rear handle and firmly

hold the tool by both front grip and rear handle

during operations.

015117

Hold the tool firmly. The tool is provided with both a front

grip and rear handle. Use both to best grasp the tool. If both

hands are holding saw, they cannot be cut by the blade. Set

the base on the workpiece to be cut without the blade

making any contact. Then turn the tool on and wait until the

blade attains full speed. Now simply move the tool forward

1. Vacuum cleaner

2. Hose

1. Dust nozzle

2. Screw

3. Lever

1. Hex wrench

1. Mounting shaft

2. Inner flange

3. Saw blade

4. Outer flange

5. Hex bolt

1. Inner flange

2. Saw blade

3. Outer flange

4. Hex bolt

Otros manuales para XSH03

Tabla de contenidos

Idiomas:

Otros manuales de Sierra circular inalámbrica de Makita

Makita

Makita BHS630 Manual de usuario

Makita

Makita BSS500 Manual de usuario