MacroAir Technologies 370 Airvolution D Manual de usuario

Rev. Date 111714

Table of Contents

Caution & Safety ................................................................................................................................. 2

Fan Placement.................................................................................................................................... 4

Fan Clearance & Placement .............................................................................................................. 5

Fan Dimensions .................................................................................................................................. 6

Fan Components & Tools ................................................................................................................... 7

Step 1 - Fan Mounting ................................................................................................................. 8

Rapid Mount Commercial .......................................................................................................... 9

1.1 Unistrut Span Mounting ....................................................................................................... 10

1.2 I-Beam Mounting .................................................................................................................. 11

1.3 Glulam/Wood Beam Mounting ............................................................................................. 13

Step 2 - Extension and Motor Unit Installation ........................................................................... 15

2.1 Extension and Motor Unit Installation ................................................................................. 16

Step 3 - Safety Cable and Electrical Installation ......................................................................... 17

3.1 Touchpad Remote Mounting................................................................................................. 18

3.2 Safety Cable & Electrical Installation .................................................................................. 20

Step 4 - Airfoil Installation .......................................................................................................... 21

4.1 Airfoil Installation .................................................................................................................. 22

Step 5 - Touchpad Remote Navigation and Operation ................................................................. 25

5.1 Touchpad Remote Navigation............................................................................................... 26

5.2 Touchpad Remote Operation ................................................................................................ 27

Maintenance Information ................................................................................................................... 28

Warranty and Technical Support ........................................................................................................ 29

Rev. Date 111714

Caution & Safety

READ THE ENTIRE MANUAL BEFORE OPERATING THE FAN. Ensure that all safety practices

and instructions are followed during the installation, operation and servicing of the fan. Failure

to apply these safety practices could result in death or serious injury. If you do not understand

the instructions please call our Technical Department for guidance (Technical Support contact

information can be found on page 29).

The fan installation should follow the recommendations outlined in this manual. MacroAir is not

responsible for any injury or damage to people or property as a result of the user and/or installer

not complying with the recommendations outlined in this manual.

All fan controls and incoming power should only be installed by qualiﬁed technicians familiar

with the requirements of the NEC and local codes. Refer to appropriate portions of this manual

for other important requirements. Failure to follow these guidelines will void the manufacturer’s

warranty.

NOTICE: All electrical controls are conﬁgured at the factory and are ready to use. No user

adjustments are available. Follow the included wiring schematics and installation instructions

when installing this device to ensure proper operation. Do not make any changes to any part of

the fan without ﬁrst consulting MacroAir.

Installation is to be in accordance with the national electrical code, ANSI/NFPA 70-1999 and local

codes.

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH.

Read and understand this manual before installing or operating a fan unit. Installation,

adjustment, repair, or maintenance must be performed by qualiﬁed personnel.

The user is responsible for compliance with all international and national electrical code

requirements with respect to grounding of all equipment.

Many of the parts of this unit operate at line voltage. DO NOT TOUCH.

Install all covers before applying power or starting and stopping the unit.

DAMAGED EQUIPMENT

Do not operate or install any fans or fan accessories that appear to be damaged.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

MAINTENANCE AND SERVICE:

If the fan does not operate properly using the procedures in this manual, BE CERTAIN TO

REMOVE ALL POWER TO THE UNIT and contact our technical department for further assistance.

Keep all body parts clear of moving part at all times.

All electrical troubleshooting and repair must be done by a qualiﬁed technician and meet all

applicable codes.

Rev. Date 111714

Caution & Safety

Key Safety System Components

MacroAir fans are engineered with key safety features to prevent pieces of the fan from falling

in the unlikely event of a catastrophic failure. Used together, these systems and devices provide

comprehensive protection of people, equipment and property. Follow the detailed instructions

precisely when installing fans, including the following:

Install Safety cable on EVERY fan. The Safety cable, if installed per MacroAir speciﬁcations,

will prevent the fan from falling in the unlikely event that the mounting system should fail. A

MacroAir fan should never be run without a properly installed Safety cable, which is supplied

with every fan along with all required hardware. You must install a Safety cable for the warranty

to be in effect. Refer to page 20.

Mark the Floor to Alert Personnel

When mounting a fan in an area where materials may be elevated into its path, MacroAir

recommends marking or painting the ﬂoor with a large crosshatched circle to alert personnel of

the overhead location of fans.

Weight Considerations

We recommend that a building structure be capable of holding approximately twice the stated

hanging weight of the fan. The maximum hanging weight for the Model 370 is 115 lbs including

the weight of an additional extension. If there is some doubt of this, a professional structural

engineer should perform a thorough evaluation of the building prior to purchasing the fans.

MacroAir provides guidelines for mounting fans; however, it is the sole responsibility of the

building owner and installer to ensure the safety of the mounting system, that the building

structure is sound and that the installation complies with all federal, state, and local codes.

Torque

The maximum torque (twisting force) that must be handled by the mounting system, including the

building structure. For a Model 370, the maximum potential torque is 20 ft-lbs.

Check Federal, State, and Local Codes

Check all relevant codes to make sure that all product certiﬁcations, product listings, and building

regulations are met. Code compliance is the responsibility of the installer.

Windy Conditions

Fans should not be operated when wind is present. Fans should not be installed in applications

where it is frequently windy.

Rev. Date 111714

Fan Placement

Sprinkler Systems and Fan Placement

In any installation where ﬁre sprinklers are in place, fan should not interfere with their correct

operation. Fans should be located no less than 3 feet below a sprinkler, and placed central to

each sprinkler quadrant. Our AirBrain motor controller can be connected to a ﬁre suppression

control system, which will emergency-stop fans in case of ﬁre. Prior to installing fans, review all

codes applicable to sprinkler systems and fans to ensure code compliance (refer to NFPA 13).

Please call our Technical Department for guidance (Technical Support contact information can be

found on page 29). However, it is your sole responsibility to see that the installation is completed

to code and that it is correct.

Other Information on Placement and Spacing

If possible, avoid mounting fans directly below lights or skylights to avoid any strobe effect caused

by moving airfoils. Note, a large fan, 20 – 24 feet in diameter, performs best at 20 to 30 feet above

the ﬂoor, but acceptable performance has been demonstrated as low as 10 feet and as high as 50

feet.

If the building has a mezzanine, fans should be mounted so a person can not reach a fan in any

way from the upper level/deck. Make certain that fans are positioned so that the airfoil tips are at

least 3 feet away from any area where a person may be able to extend outward to reach them.

Rev. Date 111714

Fan Clearance & Placement

WARNING: FANS ARE NOT MEANT TO BE OPERATED IN WINDY CONDITIONS.

Maximum Angle for Mount (feet)

Slope (in) 0 2/12 4/12 6/12 8/12 10/12

Roof Angle 0 9.5o18.4o26.6o33.7o39.8o

Diameter Recommended Total Drop (Mount to Blade) Length

6 feet 2 2 2 N/A* N/A* N/A*

8 feet 2 2 2 N/A* N/A* N/A*

10 feet 2 2 2 N/A* N/A* N/A*

12 feet 2 2 3 N/A* N/A* N/A*

*The Rapid Mount Commercial does not support this angle

The extension lengths above are minimum recommendations only, based solely on roof pitch

and fan diameter. Other factors must be evaluated when determining extension requirements.

In addition, OSHA requirements state that the fan airfoils must be a minimum of 10 feet (3.05

meters) above the ﬂoor. Contact our technical department for assistance with fan placement and

extension selection (technical support contact information can be found on page 29).

Minimum Clearance (Horizontal / Vertical inches):

Airfoil / Extension 12345678910

6 feet 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3

8 feet 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 3 3 / 4

10 feet 3 / 3 3 / 3 3 / 4 3 / 4 3 / 4 3 / 4 3 / 4 3 / 4 3 / 4 3 / 4

12 feet 3 / 4 3 / 4 3 / 4 3 / 4 3 / 4 3 / 4 3 / 5 3 / 5 3 / 5 3 / 5

The table above shows the clearance needed from the fan to obstructions such as lighting,

conduit, etc.

Rev. Date 111714

The Model 370 has a standard airfoil to mounting point clearance of 2 feet [0.61 m] with the

Rapid Mount Industrial. Refer to the Fan Clearance & Placement charts on page 5 for allowable

mounting options.

Fan Dimensions

1.833

6'0"

ILLUSTRATION

SHOWN WITH

STANDARD EXTENSION

0.441

1'5.375"

0.609

2'0"

0.720

2'4"

6' Airvolution D

300 Series

Rapid Mount Commercial

A-01

DO NOT SCALE DRAWING

MA06XS3706

SHEET 1 OF 1

9/9/2014

7/17/2014

xxxx

UNLESS OTHERWISE SPECIFIED:

SCALE: 1:20

WEIGHT:

REV

DWG. NO.

SIZE

TITLE:

MacroAir

794 S Allen St. San Bernardino, CA 92408

NAME

DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

INTERPRET GEOMETRIC

TOLERANCING PER:

DIMENSIONS ARE IN FEET AND INCHES

BRACKETED DIMENSIONS ARE IN METERS

TOLERANCES:

FRACTIONAL

.010

ANGULAR: MACH

BEND

TWO PLACE DECIMAL

.01

THREE PLACE DECIMAL

.001

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MacroAir TECHNOLOGIES. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MacroAir TECHNOLOGIES IS

PROHIBITED.

Rev. Date 111714

Fan Components and Tools

2.442

8'-0"

0.609

2'-0"

0.442

1'-5"

0.721

2'-4"

8' Airvolution D

300 Series

Rapid Mount Commercial

A-01

DO NOT SCALE DRAWING

MA08XS3706

SHEET 1 OF 1

8/5/2014

7/17/2014

xxxx

UNLESS OTHERWISE SPECIFIED:

SCALE: 1:24

WEIGHT:

REV

DWG. NO.

SIZE

TITLE:

MacroAir

794 S Allen St. San Bernardino, CA 92408

NAME

DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

INTERPRET GEOMETRIC

TOLERANCING PER:

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MacroAir TECHNOLOGIES. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MacroAir TECHNOLOGIES IS

PROHIBITED.

DIMENSIONS ARE IN FEET AND INCHES

BRACKETED DIMENSIONS ARE IN METERS

TOLERANCES:

FRACTIONAL

.010

ANGULAR: MACH

BEND

TWO PLACE DECIMAL

.01

THREE PLACE DECIMAL

.001

A - D-Drive Motor & Controller

B - Bottom Cover

C - XS Airfoil

D - Top Cover

Tools Required for Provided Hardware:

5/32’’ Allen Wrench

1/8’’ Allen Wrench (Mount Set Screw)

3/32’’ Allen Wrench

5/16’’ Allen Wrench

9/16’’ Wrench

Phillips Screwdriver

3/8’’ Socket

3/4’’ Wrench

3/4’’ Socket

Ratchet and Torque Wrenches

Rev. Date 111714

Step 1 - Fan Mounting

Choose the appropriate method for

mounting the fan(s) based upon your

speciﬁc application.

Otros manuales para 370 Airvolution D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de MacroAir Technologies

MacroAir Technologies

MacroAir Technologies Diamond HVLS Series Manual de usuario

MacroAir Technologies

MacroAir Technologies airelite Manual de usuario

MacroAir Technologies

MacroAir Technologies WhisperFoil Manual de usuario

MacroAir Technologies

MacroAir Technologies X Series Manual de usuario

MacroAir Technologies

MacroAir Technologies AirVolution D3 Manual de usuario

MacroAir Technologies

MacroAir Technologies airelite Manual de usuario

MacroAir Technologies

MacroAir Technologies 370 Airvolution D Manual de usuario

MacroAir Technologies

MacroAir Technologies AVD 370/2 Manual de usuario

MacroAir Technologies

MacroAir Technologies AirEco Manual de usuario

MacroAir Technologies

MacroAir Technologies AirVolution 550 Manual de usuario

MacroAir Technologies

MacroAir Technologies AirVolution-D 550 Manual de usuario

MacroAir Technologies

MacroAir Technologies AirVolution-D 370 Manual de usuario

MacroAir Technologies

MacroAir Technologies EnergyLogic AVD3 Manual de usuario

MacroAir Technologies

MacroAir Technologies AirVolution D3 Manual de usuario

MacroAir Technologies

MacroAir Technologies AirStar Manual de usuario

MacroAir Technologies

MacroAir Technologies AVD370 Manual de usuario

MacroAir Technologies

MacroAir Technologies AirStar Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje