M.T.H. PREMIER DREYFUSS Manual de usuario

PREMIER DREYFUSS

STEAMENGINE

OPERATING INSTRUCTIONS

This Premier Dreyfuss features a die-cast boiler and tender and operates on O-42 track.

This Premier Steam Engine contains state-of-the-art electronics with many built-in

automatic features for incredibly realistic operation. Despite these advanced features, the

locomotive is easy to operate with any compatible standard AC transformer that is

equipped with whistle and bell buttons (see the compatibility chart on page 20), and is

compatible with most other 3-rail locomotives, rolling stock, and accessories.

This locomotive is equipped with Proto-Sound 2.0 with Digital Command System

(DCS). This new system will allow you to operate your locomotive in Command mode

(when used with the DCS Remote Control System, sold separately) or Conventional

mode. Conventional operating features are described in the following pages, while the

DCS operating features are covered in the set of operating instructions that

accompanies the DCS equipment. Conventional Mode operation of this locomotive is

much simpler than operation of original Proto-Sound engines. For your own safety and

that of your equipment, please read the instructions before you operate this engine.

Premier Dreyfuss Steam Engine

Table of Contents

Set Up 3

Basic Operation 4

TransformerControls 4

Throttle 4

Volume Control 4

Proto-Sound 2.0 Operation 5

Activating Proto-Sound 2.0 Conventional Mode Features 5

Passenger Station Announcements (PSA) 6

Tips on Using PSA 7

Proto-Coupler®Operation 8

Speed Control 8

Lock into a Direction State 9

Reset to Factory Defaults 9

Automatic Sounds 9

Maintenance 10

ProtoSmoke Unit Operation 10

Lubrication and Greasing Instructions 12

Locomotive Traction Tire Replacement 13

Locomotive Light Bulb Replacement 15

Self-Charging Battery Back-Up 16

Troubleshooting 17

Compatibility 19

TransformerCompatibilityChart 20

Additional Features with DCS Remote Control System 21

SafetyPrecautions 23

Service and Warranty Information 24

Premier Dreyfuss Steam Engine

Set Up

There are a couple of simple steps you must take before operating this Premier

steamer.

1. Although the engine was lubricated at the factory, you should lubricate all

side rods and linkage components and pickup rollers to prevent them from

squeaking. Use light household oil and follow the lubrication points marked

“L” in Fig. 6 on pg. 12. Do not over-oil. Use only a drop or two on each pivot

point

2. Prime the operating smoke unit with smoke fluid before operating. Add

15-20 drops of smoke fluid through the smokestack (see Fig. 3), then gently

blow into the stack to eliminate any air bubbles in the fluid.

3. If you choose not to prime the unit with fluid, turn the smoke unit switch

located under the engine to the OFF position (see Fig. 4). Running the

engine without a primed smoke unit may cause damage. See the

“ProtoSmoke Unit Operation” section of this book for more information on

smoke unit maintenance.

4. Place the engine on the track, then insert the reverse unit plug that extends

out of the tender into the receptacle at the back of the boiler cab (Figure 1).

WARNING: DO NOT CONNECT THIS ENGINE TO A TENDER

FROM ANOTHER ENGINE; IT MAY CAUSE SERIOUS DAMAGE.

Look at the bottom of the engine and tender where each will have a

color-coded stamp. If they match you may connect those two pieces; if not,

don’t.

5. Connect the draw bar between the

engine and tender. The draw bar hole

located farthest from the tender is for

applications such as display. The second

hole is for normal operation on O-42

track.

At this point, you are ready to begin

running your engine.

Plug Tender Plug into

Boiler Socket at back of cab.

Figure 1. Connect the Tender to the

Engine

Premier Dreyfuss Steam Engine

Basic Operation

Throttle – Throttle up the power to your track. Give about 10-14 volts or

enough power so that the engine’s headlight shines brightly. Then put the

engine into motion by either firmly pressing the Direction button on your

transformer or remote once or dropping and advancing the throttle to put the

engine in forward.

Operation Buttons

Use the operation buttons on your transformer or remote as described below.

Horn/Whistle - To sound the whistle, firmly press the Horn/Whistle button.

The horn will sound for as long as you continue to depress the button. It will

stop when you release the button. The whistle has four different endings,

depending on whether you hold the button for less than three seconds, three

seconds, four seconds, or five seconds or longer.

Bell - To sound the bell, firmly press and release the Bell button. To turn the

bell off, press and release the Bell button again. The bell will continue to ring

from the time you turn it on until you press and release the button again to turn

it off.

Direction– Your train is programmed to start in neutral. The first direction

after neutral upon start-up is forward. Firmly press and release the Direction

button to allow the engine to move forward. Just as you must stop your

automobile between forward and reverse, this engine will not go directly from

forward to reverse; it goes into neutral between directions. If the train has

been moving forward, the first press of the Direction button will put the train

from forward into neutral, the second press into reverse, the third press back

into neutral, and the fourth back into forward. To prevent accidental

high-speed start-ups, this engine is programmed to restart in neutral each time

the track voltage is turned off for 25 seconds or more.

Volume Control –To adjust the volume of all sounds made by this

engine, turn the master volume control knob located under the tender

clockwise to increase the volume and counter-clockwise to decrease the

volume (see Fig. 2).

Proto-Sound2.0

VolumeAdjustmentKnob

Figure 2. Manually Adjusting the Proto-Sound 2.0 Volume

Premier Dreyfuss Steam Engine

Proto-Sound 2.0 Operating Instructions

This manual contains the operating instructions for Proto-Sound 2.0 in

conventional mode only. Instructions for accessing DCS command mode

features accompany the DCS Remote Control System equipment.

Because Proto-Sound 2.0 is an all-new system developed by M.T.H.’s own

research and development team, it operates differently from original

Proto-Sound. Most Proto-Sound 2.0 features are automatically enabled, and

the reset state has been eliminated, so there is no need to program features as

with original Proto-Sound. Although the new system is easier to operate than

original Proto-Sound, you should read these instructions thoroughly before

using Proto-Sound 2.0 features in order to prevent harm to yourself or your

equipment.

Activating Proto-Sound 2.0 Conventional Mode Features:

Proto-Sound 2.0 features are activated by sequences of Bell and Whistle

button pushes described below. Please read the full descriptions of each

feature before using it. To use these buttons to activate features rather than to

blow the whistle or ring the bell, you should press the buttons for a shorter

time (1/2 second); you may need to practice your timing to make this work

smoothly.

FeaturetoBeActivated:

Passenger Station Announcements

Fire the Rear Coupler

Speed Control On/Off

Lock into a Direction/Unlock

Reset to Factory Defaults

Button Code:

1 Bell, 2 Whistles

1 Bell, 3 Whistles

1 Whistle, 2 Bells (from Neutral only)

1 Whistle, 3 Bells

1Whistle,5Bells (from Neutral only)

Premier Dreyfuss Steam Engine

Passenger Station Announcements (PSA):

Your engine is equipped with a sound package of passenger station

announcements that you can play when you pull into a passenger station.

Each sequence described below will play as long as it is left on, randomly

generating sounds, but be sure to allow approximately 30 seconds

between the button pushes described below to allow the PSA sufficient

time to run through each sequence.

1. To cue the sound system to play the PSA, quickly but firmly press the Bell

button once followed by 2 quick presses of the Whistle button while the

engine is moving. As soon as you have keyed in this code, you will hear the

announcement for the upcoming stop and the bell will begin to ring.

2. Press the Direction button or drop and advance the throttle once to stop the

engine. This will trigger the first sequence of PSA. The reverse unit is

temporarily disabled so that the train will not move as you use the Direction

button to trigger the sounds, and Proto-Sound 2.0 has disabled operator

control over the Whistle and Bell buttons until the full PSA sequence is

complete.

3. After waiting about 30 seconds for that sequence to run, press the Direction

button again to trigger the second sequence of PSA.

4. After about 30 seconds, press the Direction button again to trigger the third

PSA sequence.

5. Again, after allowing about 30 seconds for that sequence to run, press the

Direction button one more time to trigger the fourth and final PSA sequence.

You will know it is the final sequence when you hear the “All Aboard!” call.

The bell will begin to chime and within a few seconds, the engine will start

and move out on its own at the current throttle setting, in the same direction it

was traveling when you began the sequence. Once the bell turns off, the

operator regains control of the transformer’s bell and whistle buttons and can

ring the bell or blow the whistle as usual.

Premier Dreyfuss Steam Engine

Tips on Using PSA

You can terminate PSA at anytime by turning off power to the

track for 15 seconds.

You do not have to be in Forward to use PSA. At the conclusion

of the full sequence, the train will pull away from the station in

whatever direction you were going when you activated the feature.

You can use PSA even if you are double-heading with another

engine. If the second engine is not equipped with PSA at all, you

must remember not to leave the throttle at a high voltage level once

you have stopped the engine to run the PSA. Otherwise, the engine

without PSA will begin vibrating on the track as its motors strain to

move the train, since they cannot be automatically disabled during

the PSA cycle. If the second engine is an original Proto-Sound

engine equipped with PSA, you may choose to disable it when

used in double-heading operations, so you will not experience

competing PSA sounds. To disable PSA in an original

Proto-Sound engine, see the operating instructions for that engine.

PSA can be triggered from Neutral. It will operate the same as if

triggered while in motion except that, at the conclusion of the PSA,

the engine will depart in the next direction of travel, as opposed to

the direction it was traveling before entering Neutral.

Premier Dreyfuss Steam Engine

Proto-Coupler®Operation

This locomotive is equipped with a coil-wound Proto-Coupler for remote

uncoupling action. Because the Proto-Coupler is controlled through the

Proto-Sound 2.0 microprocessor, it does not require an uncoupling track

section or modification to your layout to function. You can fire the couplers

from neutral or while in motion. Use the code shown below (and in the chart

on pg. 5) to fire the coupler.

Rear Coupler:

To fire the rear coupler, press the Bell button once followed immediately by

three pushes of the Whistle button. The sound of the liftbar and air line

depletion will play, and the knuckle will be released.

Speed Control:

M.T.H. engines equipped with Proto-Sound 2.0 have speed control capabilities

that allow the engine to maintain a constant speed up and down grades and

around curves, much like an automobile cruise control. You can add or drop

cars on the run, and the engine will maintain the speed you set.

While the engine is programmed to start with the speed control feature

activated, you can opt to turn it off. This means the engine’s speed will fall as

it labors up a hill and increase as it travels downward. It is also affected by the

addition or releasing of cars while on the run.

To turn speed control on and off,put the engine in neutral, then press the

transformer’s Whistle button one time then immediately press the Bell button

two times. Two whistle blasts will indicate that the engine has made the

change. Repeat the 1 whistle, 2 bells code to return it to the other state. You

will want to do this during the initial neutral upon start-up if you ever

couple this engine to another engine that is not equipped with speed

control to avoid damaging the motors in either engine. Each time you shut

down the engine completely, it will automatically turn speed control on.

Note: When speed control is turned off, the Proto-Sound 2.0 system will limit

the volume in order to operate more smoothly at lower voltages. Full volume

is restored upon reactivating speed control.

Premier Dreyfuss Steam Engine

Lock into a Directional State:

You can lock your engine into a directional state (forward, neutral, or reverse)

so that it will not change directions. To do this, put the engine into the

direction you want (or into neutral to lock it into neutral), run it at a very slow

crawl (as slowly as it will move without halting), and quickly but firmly press

the Horn button once followed immediately by three presses of the Bell

button. Two horn blasts will indicate that the engine has made the change.

The engine will not change direction (including going into neutral) until you

repeat the 1 horn, 3 bells code to return the engine to its normal state, even if

the engine is kept without power for extended periods of time.

Reset to Factory Defaults:

To override the settings you currently have assigned to the engine and reset it

to its factory defaults, while in Neutral press the Whistle button once,

followed immediately by five quick pushes of the Bell button. Two whistle

blasts will indicate that the engine has made the change.

Automatic Sounds:

Certain Proto-Sound 2.0 sound effects automatically play in programmed

conventional mode conditions:

Squealing Brakes play any time the engine’s speed decreases rapidly.

Cab Chatter plays at random intervals when the engine idles in neutral.

Engine Start-up and Shut-down sounds play when the engine is initially

powered on or is powered off for five seconds or more.

Premier Dreyfuss Steam Engine

Maintenance

ProtoSmoke®Unit Operation

This Premier steam locomotive contains a self-powered smoke unit that

outputs smoke through the smokestack on the roof of the engine. The smoke

unit is essentially a small heating element and wick that soaks up and then

heats a mineral oil-based fluid that emits a harmless smoke. The smoke is

then forced out of the stack by a small electric fan. Smoke volume is

controlled by the Proto-Sound 2.0 system.

With a few easy maintenance steps, you should enjoy trouble-free smoke unit

operation for years.

When preparing to run this engine, add

15-20 drops of smoke fluid through the

smokestack (see Fig. 3). We recommend

M.T.H. ProtoSmoke, Seuthe, LGB, or

LVTS fluids. Do not overfill the unit or

the fluid may leak out and coat the

interior engine components.

If you choose not to add the fluid (or

have already added the fluid but choose

to run smoke-free), turn off the smoke

unit switch located under the leading

truck (see Fig. 4). Failure either to add

fluid to the unit or to turn it off may

damage the smoke unit heating

element and/or wicking material.

When the smoke output while running

the engine begins to diminish, add

another 10-15 drops of smoke fluid or

turn the smoke unit off.

When storing the unit for long periods of

time, you may want to add about 15

drops of fluid to prevent the wick from

drying out.

After removing the engine from storage, add another 25 drops of fluid, letting

the wick soak up the fluid for 15 minutes prior to operation.

Add Smoke Fluid

Figure 3. Add Smoke through the

Smokestack

Smoke Unit

ON/OFFSwitch

Figure 4. Smoke Unit ON/OFF

Switch

Tabla de contenidos

Otros manuales de Juguete de M.T.H.

M.T.H.

M.T.H. Premier Swiss 6/8 Type II Crocodile Electric... Manual de usuario

M.T.H.

M.T.H. Empire State Express Manual de usuario

M.T.H.

M.T.H. Blue Comet Manual de usuario

M.T.H.

M.T.H. F-3 POWERED B-UNIT Manual de usuario

M.T.H.

M.T.H. EMD F40PH DIESELLOCOMOTIVE Manual de usuario

M.T.H.

M.T.H. Proto-Sound 3.0 Manual de usuario

M.T.H.

M.T.H. HO 4-6-6-4 Challenger Guía de inicio rápido

M.T.H.

M.T.H. RailKing RKS SD70ACE Guía de inicio rápido

M.T.H.

M.T.H. RailKing R-12 Subway Set Manual de usuario

M.T.H.

M.T.H. RailKing RKS SD70ACE Guía de inicio rápido

M.T.H.

M.T.H. DL-110 Manual de usuario

M.T.H.

M.T.H. tinplate traditions Manual de usuario

M.T.H.

M.T.H. N6b Manual de usuario

M.T.H.

M.T.H. Premier Dreyfuss HudsonSteam Locomotive Manual de usuario

M.T.H.

M.T.H. Premier SD60 MAC Diesel Engine Manual de usuario

M.T.H.

M.T.H. Premier 4-6-0 Camelback Steam Locomotive Manual de usuario

M.T.H.

M.T.H. Tinplate 840 Manual de usuario

M.T.H.

M.T.H. RailKing R-17 Subway Set Manual de usuario

M.T.H.

M.T.H. F59PH Manual de usuario

M.T.H.

M.T.H. PREMIER DASH-9 Manual de usuario

M.T.H.

M.T.H. Premier Climax Manual de usuario

M.T.H.

M.T.H. Premier GP40 Diesel Engine Manual de usuario

M.T.H.

M.T.H. Tinplate IVES 3243 R Electric Locomotive Manual de usuario

M.T.H.

M.T.H. Premier H10 Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario