M-Systems IDE 4000 Instrucciones de instalación
IDE 4000 Flash Disk
1.8" and 2.5"
Product Specification and User Manual
January 2005
34-PS-0304-00 Rev. 2.1
DOCUMENT CONTROL INFORMATION
DCO No.:
Title Name Date
Issued by: VP Marketing, Embedded Division Ofer Tsur January 5, 2005
REVISION HISTORY
Revision Date Description Reference
2.0 June 7, 2004 Added information for new 1.8” form factor --
Updated available capacity information Section 1.2.8
Updated reliability information Section 1.2.9
Updated supported temperature ranges Sections 1.3.1, 9
2.1 January 2, 2004
Update CHS settings information Section 1.2.8
2 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
TABLE OF CONTENTS
1. Specifications........................................................................................................................5
1.1. Critical Item Definition ....................................................................................................5
1.2. Characteristics................................................................................................................5
1.2.1. Interface Definition...........................................................................................................5
1.2.2. IDE Transfer Modes.........................................................................................................5
1.2.3. Performance ....................................................................................................................5
1.2.4. Access Time ....................................................................................................................6
1.2.5. Seek Time........................................................................................................................6
1.2.6. Input Voltage....................................................................................................................6
1.2.7. Current Consumption.......................................................................................................6
1.2.8. Memory Capacity.............................................................................................................7
1.2.9. Endurance........................................................................................................................8
1.2.10. Mean Time Between Failures (MTBF).............................................................................8
1.2.11. Physical Characteristics...................................................................................................8
1.3. Environmental Conditions ............................................................................................11
1.3.1. Temperature ..................................................................................................................11
1.3.2. Altitude...........................................................................................................................12
1.3.3. Relative Humidity...........................................................................................................12
1.3.4. Shock.............................................................................................................................12
1.3.5. Vibration.........................................................................................................................12
1.3.6. Storage Life and Data Retention ...................................................................................12
2. Drive Configuration.............................................................................................................13
3. Interface Connectors..........................................................................................................14
4. Supported IDE Commands.................................................................................................15
5. CE and FCC Compatibility..................................................................................................16
6. Label Information................................................................................................................17
7. Using the IDE 4000 Flash Disk...........................................................................................18
7.1. Unpacking the Drive.....................................................................................................18
7.2. Handling Instructions....................................................................................................18
7.3. Installing the Drive in a PC...........................................................................................18
7.4. Using the IDE 4000 in an MS-DOS-Based Platform....................................................19
7.5. Troubleshooting ...........................................................................................................19
7.6. How to Get Help...........................................................................................................20
3 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
8. Warranty...............................................................................................................................21
9. Ordering Information..........................................................................................................22
How to Contact Us....................................................................................................................23
4 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
1. SPECIFICATIONS
1.1. Critical Item Definition
The dimensions of the IDE 4000 flash disk enable mounting in a standard 2.5”or 1.8” disk drive
bay, as described in Section 1.2.11.
Note: The information written in this document refers to both IDE 4000 2.5” and 1.8” unless
otherwise stated.
1.2. Characteristics
1.2.1. Interface Definition
The IDE 4000 supports the commands listed in Section 4, in compliance with ATA4 standards.
1.2.2. IDE Transfer Modes
The IDE 4000 supports the following transfer modes:
•PIO modes 0 through 4
•DMA modes 0 through 2
1.2.3. Performance
The IDE 4000 complies with the performance requirements described in Table 1.
Table 1: IDE 4000 Transfer Rates
Operation Burst Rate (MB/sec) SustainedRate (MB/sec)
Read 16.6 3.8
Write 16.6 3.4
Performance was measured on a system with the following configuration:
•Computer with ASUS P4T533-C motherboard and Intel 2.4 GHz processor
•Windows XP Professional operating system
•IDE transfer mode: Multiword DMA 2
•IDE 4000 disk capacity: 4GB
The HDTACH v2.61 benchmark utility was used to measure IDE 4000 performance. See
Figure 1 for measurement results.
5 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
Figure 1: IDE 4000 Performance Results
1.2.4. Access Time
Standby to active (typical.): 0.1 msec
1.2.5. Seek Time
The IDE 4000 has no seek time, as it has no moving parts.
1.2.6. Input Voltage
The IDE 4000 input voltage is 3.3VDC to 5.0VDC.
1.2.7. Current Consumption
The current consumption at an input voltage of +5 VDC is described in Table 2.
Table 2: IDE 4000 Input Current Consumption with +5 VDC Input Voltage
Function/Mode Current (max) mA DC
Read 23.0
Write 23.0
Idle/Sleep 5.0
6 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
The current consumption at an input voltage of +3.3 VDC is described in Table 3.
Table 3: IDE 4000 Input Current Consumption with +3.3VDC Input Voltage
Function/Mode Current (max) mA DC
Read 16.0
Write 16.0
Idle/Sleep < 1
1.2.8. Memory Capacity
As of software version 1.09, the changes listed in Table 4 apply to the CHS (Cylinder, Heads,
Sectors) settings for the IDE 4000, capacities 128MB to 512MB (there are no changes for other
capacities).
Table 4: CHS Settings for Low-Capacity IDE 4000
Cylinder Heads Sectors
Capacity (MB) V1.08 V1.09 V1.08 V1.09 V1.08 V1.09
128 993 500 8 16 32 32
256 998 1000 16 16 32 32
512 1015 1015 16 16 63 63
Table 5 describes the different densities of the IDE 4000 (unformatted, in MB).
Table 5: IDE 4000 Flash Disk Capacities
Disk Capacity (MB) Disk Capacity (MB)
128 2048
256 2560
384 3072
512 3584
640 4096
768 5120
1024 6144
1280 7168
1536 8192
1792
7 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
1.2.9. Endurance
The IDE 4000 provides 2,000,000 write/erase cycles and an unlimited number of read cycles.
Performance is enhanced by the following features:
•Wear-Leveling Algorithm: This algorithm guarantees the use of all flash components at the
same level of the write/erase cycle.
•EDC/ECC (Error Detection Code/Error Correction): The enhanced Reed-Solomon
EDC/ECC extends disk endurance by detecting and then fixing flash blocks.
1.2.10. Mean Time Between Failures (MTBF)
Table 6 summarizes the MTBF prediction results for various IDE 4000 configurations. The
analysis was performed using a RAM Commander™ failure rate prediction.
Table 6: IDE 4000 MTBF
Product Condition MTBF (Hours)
Failure Rate per
Million Hours
IDE 4000 1GB Telcordia SR-332, GB, 25°C 2,893,495 0.3456
IDE 4000 2GB Telcordia SR-332, GB, 25°C 2,188,066 0.4570
IDE 4000 3GB Telcordia SR-332, GB, 25°C 1,759,180 0.5684
IDE 4000 4 to 8GB Telcordia SR-332, GB, 25°C 1,470,874 0.6799
A detailed MTBF report can be furnished upon request.
1.2.11. Physical Characteristics
1.2.11.1 Weight
The weight of the IDE 4000 complies with the values defined in Table 7.
Table 7: IDE 4000 Maximum Weight
Memory Capacity (MB) 2.5” Unit Weight (g) 1.8” Unit Weight (g)
8192 90 30
1.2.11.2 Dimensions
Table 8 describes the nominal dimensions of the IDE 4000. Refer to Figure 2 for detailed
mounting configuration dimensions.
Table 8: Nominal Dimensions
Dimensions IDE 4000 2.5” IDE 4000 1.8”
Height 0.291 in 7.40 mm 0.339 in 8.6 mm
Width 2.750 in 69.85 mm 2.008 in 51.0 mm
Depth 3.945 in 100.20 mm 3.004 in 76.3 mm
8 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
Recommended Tightening Tourqe is 6.0 in-lb (0.675 N-m)
Recommended Tightening Tourqe is 6.0 in-lb (0.675 N-m)
Figure 2: IDE 4000 2.5” Assembly
Figure 3: IDE 4000 1.8” Assembly
Notes: 1. All dimensions are in mm [in].
2. General tolerance is ±0.25 mm [±0.01 in].
9 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
1.2.11.3 Connector Interface
The pinout for the IDE 4000 interface connector is detailed in Table 9 and in Figure 4.
Table 9: J1 Pin Assignment
Pin Number Signal Name Pin Number Signal Name
1 RESET- 2 GND
3 HD7 4 HD8
5 HD6 6 HD9
7 HD5 8 HD10
9 HD4 10 HD11
11 HD3 12 HD12
13 HD2 14 HD13
15 HD1 16 HD14
17 HD0 18 HD15
19 GND 20 KEY
21 N.C. 22 GND
23 HIOW- 24 GND
25 HIOR- 26 GND
27 IORDY 28 CSEL
29 N.C. 30 GND
31 INTRQ 32 IOCS16-
33 HA1 34 PDIAG-
35 HA0 36 HA2
37 CS0- 38 CS1-
39 DASP- 40 GND
41 VCC 42 VCC
43 GND 44 RSVD
Table 10: J2 Pin Assignment
Pin Number Signal Name Pin Number Signal Name
47 Master/Slave 48 Master/Slave
49 Master/Slave 50 Master/Slave
10 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
Tabla de contenidos
Otros manuales de Almacenamiento de M-Systems
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario