M-system Mini-M M2VV Manual de usuario

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5017 Rev.5 P. 1 / 2

INSTRUCTION MANUAL

Mini-M™

VOLTAGE DIVIDER MODEL M2VV

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner (body + base socket).............................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■GENERAL PRECAUTIONS

• Before you remove the unit from its base socket or mount

it, turn off the input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +60°C

(23 to 140°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with ca-

bles, etc.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

COMPONENT IDENTIFICATION

Model

Body Base Socket

Connection

Diagram

Specifications

Fixing Screw

INSTALLATION

Loosen the ﬁxing screw at the front of the unit in order to

separate the body from the base socket.

DIN Rail

35mm wide

Spring Loaded

DIN Rail Adaptor

■DIN RAIL MOUNTING

Set the base socket so that

its DIN rail adaptor is at

the bottom. Position the

upper hook at the rear side

of base socket on the DIN

rail and push in the lower.

When removing the socket,

push down the DIN rail

adaptor utilizing a minus

screwdriver and pull.

■WALL MOUNTING

Refer to “EXTERNAL DIMENSIONS.”

M2VV

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5017 Rev.5 P. 2 / 2

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

21.5 (.85)

70.5 (2.78)

84 (3.31)10 (.39) 15 (.59)

6 (.23)

59 (2.32)

DIN RAIL

35mm wide

[4 (.16)]

8–M3

SCREW

72 (2.83)

23 (.91)

2–4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

114 (4.49)

• When mounting, no extra space is needed between units.

14 13

4 (.16)

■CONNECTION DIAGRAM

–

OUTPUT

–

INPUT

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG.Co.Ltd, Nichifu Co.,ltd

6 (.24) max

3.3 (.13) max

mm (inch)

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Otros manuales de Equipo de prueba de M-system

M-system

M-system Mini-M Series Manual de usuario

M-system

M-system M2PRU Manual de usuario

M-system

M-system Mini-M M2PHS Manual de usuario

M-system

M-system Mini-M M2XF2 Manual de usuario

M-system

M-system M6DPP Manual de usuario

M-system

M-system Mini-M Series Manual de usuario

M-system

M-system FDU Manual de usuario

M-system

M-system Mini-M M2PP Manual de usuario

M-system

M-system Mini-M M2MLS Manual de usuario

M-system

M-system W2PP Manual de usuario

M-system

M-system Mini-M M2CRS Manual de usuario

M-system

M-system Mini-M Series Manual de usuario

M-system

M-system Mini-MW Series Manual de usuario

M-system

M-system Mini-M M2PHS2 Manual de usuario

M-system

M-system Sentronic Mini-M M2RS Series Manual de usuario

M-system

M-system Sentronic M5DY Series Manual de usuario

M-system

M-system Sentronic Mini-M M2VF2 Series Manual de usuario

M-system

M-system M2PA Series Manual de usuario

M-system

M-system Mini-M M2LMS Manual de usuario

M-system

M-system Mini-M M2TG-14-M2 Manual de usuario

M-system

M-system Sentronic Mini-M M2MS Series Manual de usuario

M-system

M-system M6NPP Manual de usuario

M-system

M-system M5XAMS Manual de usuario

M-system

M-system AD2LC Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario