M-Power Diamond Cross Manual de usuario
Circular Sawblades
Suggested: Single Handle File
Fine: For regular maintenance
Coarse: For dull blades
TECHNICAL DATA
Code Grade Grit Micron
Router Bit Fine 600 25
Sharpener Coarse 300 50
Credit Card Fine 600 25
Stone Coarse 300 50
Single Fine 600 25
Handle File Coarse 300 50
Twin Handle Coarse 300 50
File X/C Ex. Coarse 100 140
Twin Handle Fine 600 25
File C/F Coarse 300 50
8” Bench Stone Super Fine 1000 15
Coarse 300 50
MOUNTING THE 8” BENCH STONE ON
THE DIAMOND STONE HOLDER
The 8” bench Stone comes with two
diamond stone holders.
Attach one diamond
holder to the underside
at each end of the
stone using the
magnetic lock to secure
in position.
To prevent skidding ensure
worksurface is dry, flat and
clean of debris.
ROUTER BIT SHARPENER
CREDIT CARD STONE
SINGLE HANDLE FILE
TWIN HANDLE FILES
BENCH STONE
followed to ensure that the stone will give
lasting performance under normal
conditions.
Follow the hints and tips explained here
to help maximise the life of your Diamond
Cross Stone:
All tooling should be cleaned before
sharpening. Resin build-up should be
removed with Resin Cleaner and a wire
brush.
Use with Diamond Abrasive Lapping
Fluid (water can be used if necessary),
this will prevent the diamonds
becoming clogged with swarf.
Diamond Cross Stones require a
'break-in' period. Initially the diamond
will feel coarse and will smooth
overtime.
Do not apply too much pressure.
The diamond is extremely abrasive so
what would normally take 5-10 minutes
on an oilstone may take approximately
20 seconds on the Diamond stone.
Dry the Diamond Cross stone
thoroughly after use. Any wet steel
filings left on the stone will cause
surface rust to form.
DIAMOND CROSS
Thank you for purchasing this product.
The following symbols are used
throughout these instructions.
Denotes risk of personal injury, loss
of life or damage to the tool in case
of non-observance of these instructions.
Refer to Power Tool instructions.
INTENDED USE
This product is intended to be used to
sharpen steel, tungsten carbide & high
speed steel tools. For both professional
and domestic use.
SAFETY
Please read and understand these
instructions before use.
Users must be competent in using
Woodworking equipment before using our
products.
All cutting edges are very sharp and care
must be taken to prevent injury.
GUIDELINES
Diamond Cross stones allow fast, clean
stock removal,with less effort and time
required and can be used on a variety of
cutting edges.
When using Diamond Cross stones,
certain general guidelines should be
OPERATION
Router Bits/Cutters
Suggested: Router Bit Sharpener
Fine: For Tungsten Carbide.
Coarse: For High Speed Steel.
Always sharpen the flat face,
never the profile/relief.
Slide the cutter with slight
pressure along the whetstone.
Repeat same number of strokes
on each cutting edge.
Chisel/Plane Irons
Suggested: 8” Bench Stone
Fine: For edge honing
Coarse: Areas of minor damage
Finish with one light stroke on
the back of the chisel.
It is recommended to use a figure of eight
motion when sharpening chisels.
Keep the bevel of the chisel/plane
iron flat on the stone.
Keep the diamond
surface flat to
the face of saw
tooth.
Use a few light,
smooth, back
and forth strokes
on each tooth.
Repeat the same
number of strokes on
each tooth.
Mark the first tooth sharpened
with chalk or masking tape to
avoid honing a second time.
UNIVERSAL
INSTRUCTION MANUAL
re-cycleread version
2
Axes
Suggested: Twin Handle File C/F
Fine: To hone the edge
Coarse: To prepare the edge
Knives
Suggested: 8 “ Bench Stone
Fine: To keep a razor edge
Coarse: To restore an edge
Small pointed tools and gouges
Suggested: Credit Card Stone
Fine: To maintain an edge
Coarse: To restore a dull edge
Mower Blades
Suggested: Twin Handle File X/C
Fine: To hone the edge
Coarse: To prepare the edge
Shears and Scissors
Suggested: Credit Card Stone
Fine: To hone the edge
Coarse: To prepare the edge
Mount the axe
in a vice.
Keep the same angle as the knife
bevel on the diamond stone.
The angle is 20˚
for most knives.
Keep the bevel on the back of the
gouge flat on the diamond stone.
Roll the tool gently to hone.
Fix the
mower blade
position using
two clamps.
Dismantle the shears to work on the
cutting blade.
Lay the diamond stone flat on the
cutting edge bevel.
Stroke smoothly towards the tip of the
blade.
Lay the stone flat on the sliding face
and remove the burr with a light stroke
(as per the main image above).
Keep the diamond
surface flat to the
face of the blade
edge.
Perform light
strokes back
and forth.
Small tools should be honed as per
chisels, pointed tools should be
honed as per gouges.
Keep the diamond
surface flat to the tip
of the Axe blade
edge.
Perform light
strokes back
and forth on
both sides.
20˚
ACCESSORIES
Non-slip magnetic Diamond Stone
Holder (pair) - Ref 21
Suitable for use with Diamond Cross
Router Cutter Sharpener, Credit
Card & 8” Bench Stones.
Also fits all other brands of credit card
and bench diamond stones.
DIAMOND STONE MAINTENANCE
Continual satisfactory operation depends
upon proper tool care and regular
cleaning.
Cleaning
Clean with a damp cloth or cleaning
(eraser) block.
Storage
Ensure diamond stones are stored
separately.
Do not store the diamond stones in
damp conditions.
ENVIRONMENTAL PROTECTION
Re-cylce raw materials instead of
disposing as waste.
Packaging should be sorted for
environmental-friendly re-cylcing.
300
Stroke away from the body, alternating
on each said of the knife.
Light strokes will produce a finer edge.
300
The product and its accessories at the
end of its life should be sorted
for environmental-friendly recycling.
GUARANTEE
All MPOWER products are guaranteed
against any defects in either
workmanship or material, except
products that have been damaged due to
improper use or maintenance.
POLICY
Our policy of continuous improvement
means that specifications may change
without notice. MPOWER Tools Limited
cannot be held liable for any material
rendered unusable, or for any form of
consequential loss.
Manufactured by MPOWER Tools Ltd
Tel: 0044 (0)1980 629 526
Email: [email protected]
Email: [email protected]
Web: www.m-powertools.com
Manor Farm Reserve - Newton Tony - Salisbury
Wiltshire - SP4 0HA - UK
© Copyright MPOWER Tools Ltd 2018
50117
Otros manuales de Herramientas eléctricas de M-Power
