M Design True Vision 1000 RD Manual de usuario
12-2019
TRUE
ISION
1000 - 1300 RD
INSTRUCTIONS FOR INSTALLATION AND USE
Distributor/Manufacturer
M-Design Benelux BVBA
B-8210 Zedelgem - Belgium
Instructions for installation and use TRUE VISION 1000-1300RD Gas
VERY IMPORTANT
INSTALLATION INSTRUCTIONS
FOR THE M-DESIGNG GAS
FIREPLACES
THE SUPPLIER TAKES NO RESPONSBILITY FOR ANY
POSSIBLE DAMAGE, POOR WORKINGAPPLIANCES AND
ACCIDENT AS A RESULT OF INCORRECT
INSTALLATION
MAINTENANCE GAS FIREPLACE M-DESIGN
THE M-DESIGN GAS FIREPLACES MUST BE CHECKED EVERY
2 YEARS AND GET A
MAINTENANCE. THIS IS ALSO TO MAINTAIN YOUR
WARRANTY. IF THIS WILL BE NOT
OBSERVED, THE WARRANTY FELL.
YOU CAN RELY ON M-DESIGN TO MAKE THIS CHECK FOR
YOU, OR YOU CAN DO THIS BY YOURSELF AND FOLLOW
THE METHOD BELOW.
3
Instructions for installation and use TRUE VISION 1000-1300RD Gas
SUMMARY
1. GENERAL REMARKS......................................................................................................... 5
2. CONNECTION.......................................................................................................................... 5
3. INSTALLING THE FIREPLACE...................................................................................... 6
3.1.1 Positioning the fireplace................................................................................... 6
3.1.2 Nearbox (Gasunit).................................................................................................. 7
3.1.3 The Gas connection.............................................................................................. 8
3.1.4 Electrical connection ........................................................................................... 9
3.1.5 Modification natural gaz to propane........................................................ 9
4. INSTALLING THE CHIMNEY ........................................................................................ 10-13
5. FLAME ADJUSTMENT SETTINGS............................................................................. 14
6. INSULATION AND FINISHING ..................................................................................... 14
7. CONVECTION CURRENT ................................................................................................ 15-16
8. POSITIONING THE LOGS ................................................................................................ 17-20
9. FIRST-TIME USE................................................................................................................... 21
10. SAFETY, ADVICE AND MAINTENANCE............................................................ 21
11.GUARANTEE ......................................................................................................................... 22
12. REMOTE CONTROL ......................................................................................................... 23-25
13. DRAWINGS............................................................................................................................ 26
4
Instructions for installation and use TRUE VISION 1000-1300RD Gas
OPEN EN CLOSE THE DOOR
For initial setup, you need to clean the window and clear the fireplace of any
dust and grease that is left behind. This is also the only maintenance action
that may be performed on the device by the user.
Thanks to a patented system, the door can be easily opened at an angle of 45° to allow a user-
friendly cleaning of the window
To close, push the door gently (but not to soft) against the hooks. Make sure that all
hooks are hooked
CLOSING
OPEN
Above the glass (below the upper frame) hooks are provided (left, right and center). Push
it upwards with your fingers. the window can now be opened.
5
Instructions for installation and use TRUE VISION 1000-1300RD Gas
1. General remarks
This is an appliance using the closed combustion system, designed for the atmosphere and
comfort of your living-room. It constitutes an ecient source of heat and gives the impres-
sion of a real fire.
The balanced flue appliances are based on the principle of natural extraction from the fire-
box, which eliminates flue gas outside and brings in air (oxygen) from outside the house
which is necessary for combustion of the gas. It uses to this eect two concentric pipes.
The internal pipe ensures the elimination of burned gases and the external pipe brings in
combustion air. The advantage of this principle is that the equipment works independently
of the atmosphere which predominates in the house.
2. Connection
This appliance must be connected by an approved installer in accordance with the most
recent
regulations in force. On the basis of your order specifications, this appliance is designed for
natural or propane gas.
Read the instructions before installing and using this appliance. Before installing the ap-
pliance, please check the local regulations about this type of appliance (identification of
the type of gas, etc.) and check that the furnace is adapted to your means of installationt.
It is imperative that the installer sees to the following:
• The appliance must be subject to an air tightness test of the gas and elimination of flue
gases.
• The concentric pipe, if already available, must be working correctly.
• The running of the control valve, lighting of the pilot light, the main burner and the
thermocouple must all be checked.
This appliance has been programmed and factory sealed. The sealed parts cannot be mo-
dified. The appliance may therefore also be installed in airtight accommodation and ac-
commodation equipped with mechanical ventilation. It constitutes ambient heating even in
accommodation equipped with a closed ventilation system.
The appliance must be connected to the type of gas mentioned
on the appliance. Never connect a propane burner to natural
gas or vice versa!
6
Small saucers provided
with fireplace
Instructions for installation and use TRUE VISION 1000-1300RD Gas
3. Installing the fireplace
After having checked the appliance, you are ready to install your appliance. This is
done as follows
3.1.1 Positioning the appliance
Place the appliance on a stable surface using the adjustable feet. Adjust the height of the
appliance turning the bolt ( pic 1 )
Minimum and Maximum hight of the appliance :
Adjusting the height of the appliance Min 35mm to 450mm (floor to under the appliance).
If you want the fireplace to be installed with a dierent height, unscrew the nut to remove the feet.
Grind the desired height on foot. The distance between two holes is 40mm. With the fireplace is provided 4
small saucers. Use to get the stud under your feet.
If you want to install the fireplace at the minimum height of 25mm, measured from the floor to
Below the firebox: remove the foot and unscrew the nut below the foot. Aim the nut in
The tarred hole that is located below the hearth in the corner. Do the same for the four feet.
The minimum distance from the floor to the bottom of the frame is 244mm
The appliance must not be placed directly on the floor as you need to allow
natural convection. The appertures for the air supply (IN) is situated
underneath the appliances
7
Dimensions gasunit 3 branders : L455 xB188 x H64mm
Dimensions gasunit 3 branders : L365 xB188 x H64mm
Instructions for installation and use TRUE VISION 1000-1300RD Gas
For safety reasons, The gasbattery or “NEARBOX” is fixed with screws on the pallet.
Unscrew and remove the gasunit before installation
gas connection1/2”
reciever
DFGT-03MC01 V09
Transmitter burner
Gas valva
VK4105ME5004
3.1.2 Nearbox (gasunit)
gas connection1/2”
to main burner
Electro magnet ventil 1 or 2 burners
NEARBOX FOR 1 BURNER
NEARBOX FOR 2 BURNERS
to main burner
(455 2 burners)
to second burner or side burner
220V
NEARBOX
Connection Gas 1/2” (provide tap)
8
Instructions for installation and use TRUE VISION 1000-1300RD Gas
Opening provided in wall
for maintenance
Cable to ionistation pin
GAS SUPPLY TO MAIN BURNER ( RED)
flexible for GAS
True Vision is provided with
a direct ignition , no starting
pilot
3.1.3 The Gas connection
Valve 1/2”
After the “NEARBOX” has removed from the of the back of the fire, you can place it loosely on the ground
in proximity to the opening provided in the wall of mantelpiece. The device is always connected with an
approved gas tap 1/2, and preferably with a yellow gasflexible that is reachable at all times. Provide the
mantelpiece with a door so that the valve and the electrical connection is easily accessible.
GAS SUPPLY TO SIDE BURNER OR SECOND
BURNER (YELLOW)
ATTENTION : DO NOT PLACE ANY DECORATION ON THE DIRECT IGNITION PIN
(be carefull to stay out of the little rectangular zone with the dcoration)
9
Instructions for installation and use TRUE VISION 1000-1300RD Gas
3.1.4 Electrical connection
These appliances are equipped with a radiographic remote control, making an earthened 220V
socket necessary.
You should bear in mind that the appliance must be connected to all
electrical supplies for the purposes of service.
It’s obligatory to connect an earth current.
3.1.5 Modification natural gaz to propane
Modification of the fireplace can only be done by the manufacturer or an approved installer. A new
signal plate is provided.
10
C
C
Instructions for installation and use TRUE VISION 1000-1300RD Gas
4.1. ROOF EXIT (C31)
The concentric flue duct should not be reduced to 150/100 for all True Vision.
Picture 1
4. Installing the chimney
Install the concentric flue duct as indicated by ONTOP - METALOTERM. The only authorised pipes are ONTOP
Metaloterm™. ONTOP-METALOTERM tested our appliances with their conduct and we only guarantee a good
working of the appliance with those. Between the external wall of the pipe and the wall or the ceiling, you
should allow for a clearance of at least 50mm and protection that is suitable against temperatures of around
130°C. The passage of the front panel cowl in the external wall must be filled in using silicone mastic.
Ø 200/130
Appliance C (min) C (max) Restricon (as from 3m)
True Vision 1000 RD 2 m 10m Ø 60
True Vision 1300 RD 2 m 10m Ø 60
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Chimenea de interior de M Design
M Design
M Design Luna Diamond Series Manual de usuario
M Design
M Design VENUS Manual de usuario
M Design
M Design VENUS DHT Manual de usuario
M Design
M Design Luna Diamond Series Manual de usuario
M Design
M Design ZINO 700 Manual de usuario
M Design
M Design INTERRA 60 Manual de usuario
M Design
M Design LUNA 700H Manual de usuario
M Design
M Design LUNA 850 V Gold Gas Manual de operación y mantenimiento
M Design
M Design INTERRA 60 Manual de usuario
M Design
M Design Luna Gold+ Series Manual de usuario
M Design
M Design VENUS GREEN PLUS 700 Manual de usuario
M Design
M Design Luna Diamond Series Manual de usuario
M Design
M Design ARGENTO H Series Manual de usuario
M Design
M Design VENUS GREEN PLUS Series Manual de usuario
M Design
M Design LUNA DIAMOND 100DH Manual de usuario
M Design
M Design LUNA 700H Manual de usuario
M Design
M Design LUNA GOLD 800DC Guía
M Design
M Design LUNA 850 V Gold Gas Manual de usuario
M Design
M Design Venus True Vision Series Manual de usuario
M Design
M Design TRUE VISION RUSTICA Manual de usuario
