Lynx L36 Series Manual de usuario

LCB2-3 INSTALLATION INSTRUCTIONS

TOOLS REQUIRED: 7/16 Wrench

CONTENTS OF KIT: An adjustable side burner mounting bracket

Side shelf mounting bracket with 7/16 fasteners

Decorative cover for the L27 and L36 models

The side burner support bracket comes preassembled for the L27 and L36

Lynx Grills, 7300 Flores St., Downey, CA 90242

Customer Care Ph.: 888-289-5969/ Fax: 562-299-6978/Service@lynxgrills.com

P/N 34912 8/14

INSTRUCTIONS FOR MODELS L36 and L27:

1. Remove the right hand side shelf and the cabinet back panel (fig. 1)

2. Mount the LCB2-3 side burner to the supports (fig. 2)

3. If needed, any misalignment can be corrected by 1st measuring the amount of misalignment, 2nd loosening the

bracket support fasteners. 3rd raise or lower the bracket according to your measurements.

Tighten the fasteners. (fig 3)

4. Hang the side shelf removed in step 1 on the right side shelf support pins of the side burner (Fig. 6, pg. 2)

P/N 34912. 8/14

Rear View

INSTRUCTIONS FOR MODELS L54, L42, L30:

1. Remove the right hand side shelf. See fig.1 on page 1

2. At the rear, remove the decorative cover (1) on the left hand side of the LCB2-3 by removing the Philips head screw

and sliding it out. This also gives access to the gas piping connections. (Fig. 2)

3. Locate the mounting bracket on the inner most bracket support (Fig 3). Remove the 7/16 fasteners holding it in

place Reinstall the mounting bracket on the rear most bracket support and secure it with the 7/16 fasteners

4. As in step 3 on page 1,correct any misalignment in the shelf

5. Move the shelf mounting bracket on the right hand side, to the outermost mounting holes using the 7/16 nuts, and

tighten. (Fig. 5)

6. Hang the side shelf removed in step 1, pg. 1 to the right side of side burner on the shelf mounting bracket pins

(Fig 6)

Remove the bracket from the inside

support and install it onto the outer

support

This bracket must be mounted in the outer

position

Once the side burner is mounted to the grill the gas con-

nections can be made. Refer to the illustrations on the

right for proper gas installation examples.

After the side burner gas connections are made it is rec-

ommended that a leak test be done on all gas line fittings.

Apply a soap and water solution to all connections and

look for bubbles to form which indicate a gas leak. If no

bubbles are present, make the electrical connections

The side burner is electrically connected to grill at the

transformer. Disconnect the transformer from the grill

and plug in the side burner as shown in the illustration

below.

Finished Dimensions

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Parrilla de otras marcas

Orbegozo

Orbegozo GR 2300 Manual de usuario

bora

bora PT11 Manual de usuario

Klarstein

Klarstein 10031664 Manual de usuario

Garland

Garland MWE3W Manual de usuario

Char-Broil

Char-Broil 463722714 Manual de usuario

Nexgrill

Nexgrill 720-0830HK Manual de usuario

Kenmore

Kenmore 415.16123800 Manual de usuario

Camp Chef

Camp Chef PG24CLAU Manual de usuario

Tucker Barbecues

Tucker Barbecues GTR Series Instrucciones de montaje

Monogram

Monogram ZGG540NCP1SS Manual de usuario

Equipex

Equipex Sodir Savoy Manual de usuario

Gaggenau

Gaggenau VR 414 610 Manual de usuario

Miele

Miele KM 408-1 Manual de usuario

George Foreman

George Foreman GGR50B Manual de usuario

AOG

AOG T series Manual de usuario

Gorenje

Gorenje TG2000CB Manual de instrucciones

Weber

Weber Genesis Silver-B Permamount NG 051701 Manual de usuario

Glen

Glen SA 3037 Manual de usuario