Luminaire led AEL Manual de usuario

RETAIN THESE INSTRUCTION FOR FUTURE USE

Page 1 of 4

SAFETY PRECAUTIONS

WARNING - Risk of fire or electric shock. Basic safety precautions should always be

followed when using electrical equipment.

WARNING - This product must be installed in accordance with the applicable

installation code by a person familiar with the construction and operation of the

product and the hazards involved.

WARNING - Disconnect power to all circuits before wiring fixture.

WARNING - Install in accordance with all national, state, and local codes.

WARNING - Do not connect to an ungrounded supply.

WARNING - Read all fixture markings and labels to ensure correct installation of

fixture.

WARNING – Do not apply power to the fixture until the LED Board assembly is

connected to the driver. If power is applied to the fixture prior to connecting the LED

Board assembly to the driver, this will cause the LED Board to fail and void the

warranty.

AEL INSTALLATION GUIDE U.S. Patent D584,444

RETAIN THESE INSTRUCTION FOR FUTURE USE

Page 2 of 4

CAN ICES-005 (A) / NMB-005 (A)

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

ISED CANADA STATEMENT / DECLARATION POUR ISDE CANADA

This class A lighting equipment complies with Innovation, Science and Economic

Development (ISED) Canada Standard for radio interference-causing equipment ICES-

005, 5th edition.

Ce matériel d’éclairage de classe A est conforme avec la norme sur le matériel

brouilleur radio NMB-005, 5ième édition, publié par innovation, science et

développement économique (ISDE) Canada.

AEL INSTALLATION GUIDE U.S. Patent D584,444

INSTALLATION PROCEDURE

Preparation

1. Mounting surface must be relatively flat. Split face block, natural stone veneer, or deep grout lines

may require additional preparation such as concrete pads.

2. Fixture is designed to cover a 2 x 3 electrical box, mounted horizontally. See Fig. 2

3. Wiring must enter in the center of the fixture; prepare recessed junction box in center. Distance from

center hole to bottom of finished unit will be 1.416”. See Figure 2

Installation

1. Detach Wall bracket from fixture by loosening (2) screws and sliding apart on a 45 degree angle. (fig1)

2. Using ¼” hardware (not supplied), attach Wall Mount Bracket to mounting surface. Bracket must be

level. If the mounting surface is slightly curved or warped, it may be advisable to leave a small

amount of play in some of the mounting points as the fixture will pull the bracket straight when

mounted. Use hardware with heads that are no more than 1/8” thick. (fig2)

Figure 1

Figure 2

Page 2 of 4

3. Align fixture over mounting bracket and push wires through center hole. Fixture should align from the

top of the bracket and will rest on the angled surface. Tighten two mounting screws to secure fixture

to bracket. (fig3).

4. Apply a bead of silicone caulk between the wall and top of fixture as required.

5. Loosen (3) screws in lens frame and swing door frame downward. (fig4)

6. Remove reflector by loosening ¼ hex screws.

7. Connect supply wires in accordance with code.

8. Re-install reflector

9. Install Lamp(s)

10. Tighten (3) Tamper Resistant screws to secure door frame.

11. Energize and test.

RETAIN THESE INSTRUCTION FOR FUTURE USE

Figure 3

Figure 4

Page 4 of 4

Tabla de contenidos

Otros manuales de Equipo de iluminación de Luminaire led

Luminaire led

Luminaire led LVP1212 LED Series Manual de usuario

Luminaire led

Luminaire led CLF11L Manual de usuario

Luminaire led

Luminaire led VPF4 Series Manual de usuario

Luminaire led

Luminaire led VPF4 Series Manual de usuario

Luminaire led

Luminaire led FFW1212 Series Manual de usuario

Luminaire led

Luminaire led ARV17/YRV17 LED Manual de usuario

Luminaire led

Luminaire led ESF18 Manual de usuario

Luminaire led

Luminaire led CMP Series Manual de usuario

Luminaire led

Luminaire led TSL9 LED Series Manual de usuario

Luminaire led

Luminaire led LVP751 Manual de usuario

Luminaire led

Luminaire led LVP58 Manual de usuario

Luminaire led

Luminaire led SWP610 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario