Lucent Technologies 954 Manual de usuario
Part 2
Please read Part 1 — Important Product
Information, included in your package.
User’s Manual for
Four-Line Intercom/
Speakerphone 954
Lucent 0954 cover.L1 5/9/98, 12:17 PM3
© 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in Mexico. Issue L1
Lucent 0954 cover.L1 5/9/98, 12:17 PM2
1
CONTENTS
BEFORE YOU BEGIN ........................ 3
INSTALLATION................................. 4
Table/Desk Installation.......................... 4
Wall Installation..................................... 6
TELEPHONE FEATURE SETUP .........10
Assign Intercom Number ....................10
Set the Clock. ...................................... 10
Set Dial Mode ...................................... 10
Set forTwo orThree Phone Lines........11
Set Up for a Private Line...................... 11
Change BATTERY Display ...................11
OPERATION................................... 12
Making a Call....................................... 13
Call Privacy ......................................... 13
Line-In-Use Lights ................................ 13
Volume ................................................ 14
Redial .................................................. 15
Auto Redial.......................................... 15
Hold .................................................... 15
Switch Between Lines .........................15
Mute .................................................... 16
Flash .................................................... 16
TemporaryTone Dialing ...................... 16
Conference Calls ................................. 16
Do Not Disturb.................................... 17
Transfer a Call...................................... 17
Timer................................................... 18
TELEPHONE MEMORY ....................19
Directory Card .................................... 20
Storing Numbers in Memory...............20
Storing a Pause in a
Memory Number ............................. 20
Storing aTemporaryTone Signal
in a Memory Number ...................... 20
Storing Flash in a Memory Number ....20
Erasing Memory Numbers................... 20
INTERCOM OPERATION ..................21
Basic Intercom Operations..................22
Making an Intercom Call or Page ........22
Answering an Intercom Call or Page...22
Ending an Intercom Call or Page.........22
PagingAll Phones ................................ 23
Answering anALLPAGE ....................... 23
Making an Intercom
Conference Call ............................... 23
Room Monitor ..................................... 23
CheckingYour Station Number...........23
IN CASE OF DIFFICULTY .................24
EXPANDING THE 954 SYSTEM........26
CENTREX OPERATION ....................27
Setup Checklist ................................... 27
Setting Up a Fourth Line
for Each Station ............................... 27
Enabling/DisablingAttendant Station..27
Attendant Operation ........................... 28
Setting Ring Delay Duration................28
Answering a Delayed Ring .................. 28
Picking UpAnother Station’s Line .......29
Lucent 0954 book.L1 5/7/98, 10:34 AM1
2
Lucent 0954 book.L1 5/7/98, 10:34 AM2
3
BEFORE YOU BEGIN
• You must have a modular telephone jack and electrical outlet near
where you’re installing the phone.
• The total length of telephone line cord used in this system is
important. If the total length of telephone line cord is more than
600 feet,you may need to use a special filter device. You can call
1 800 PCC–9125 for information about this filter. You’ll need to
contact a professional to install this filter.
• Identify the number of phone lines you’ll use.
• All connected phones must have the same Line 1 phone number for
Intercom and Paging to work.
• Assign a different Intercom Extension Number (11 through 22) to
each 954 telephone. You’ll need to do this individually at each
telephone.
• Decide if you want a private line. A private line does not appear on
all connected phones.
Lucent 0954 book.L1 5/7/98, 10:34 AM3
4
Table/Desk Installation
1 Install 3 AAA batteries.
• Press in on the tabs and remove the telephone base.
• Press in on the tabs on the battery door,and remove it.
• Insert 3AAA batteries,and replace the battery door.
• Replace the telephone base.
NOTE: Batteries retain telephone memory in the event of a power failure.
If power fails, this phone will not work.
INSTALLATION
2 Connect the telephone line cords to the telephone.
NOTE: If the phone rings when you first connect the line cords, you need
to set the phone’s intercom number. See “Assign Intercom Number”in the
TELEPHONE FEATURE SETUP section of this manual.
•Four One-Line Jacks
Modular
Telephone Jacks
Lines 1 and 2
Modular
Telephone Jacks
Lines 3 and 4
Telephone Jacks
Power Cord
Telephone
Line Cords
Standard
Electrical
Outlet
Lucent 0954 book.L1 5/7/98, 10:34 AM4
5
•Two Two-Line Jacks
INSTALLATION
Telephone
Line Cords
Telephone Jacks
Modular
Telephone Jack
Lines 1 and 2
Modular
Telephone Jack
Lines 3 and 4
Power Cord
Standard
Electrical
Outlet
3 Connect the power adapter.
Use only the power adapter provided with this product. To obtain a
replacement,call 1 800 PCC–9125.
Plug one end of the power adapter into the jack labeled ADAPTER
on the back of the phone. Plug the other end into a standard
electrical outlet.
4 Connect the handset cord.
Plug one end of the coiled handset cord into the jack on the bottom
of the phone. Plug the other end into the handset, and hang up.
5 Check for dial tone.
Lift the handset and listen for a dial tone. If you cannot hear a dial
tone,turn to IN CASE OF DIFFICULTY in this manual.
Lucent 0954 book.L1 5/7/98, 10:34 AM5
6
Wall Installation
1 Reverse the handset tab.
Hold down the switchhook,then pull the tab out and rotate it 180
degrees. Release the tab so it settles into position.
2 Install 3 AAA batteries.
• Press in on the tabs and remove the telephone base.
• Press in on the tabs on the battery door,and remove it.
• Insert 3AAA batteries,and replace the battery door.
3 Turn the base, as shown, and attach it to the bottom of the
phone.
INSTALLATION
Lucent 0954 book.L1 5/7/98, 10:34 AM6
7
4 Connect the telephone line cords to the telephone.
•Four One-Line Jacks
•Two Two-Line Jacks
5 Connect the power adapter to the telephone.
Use only the power adapter provided with this product. To obtain a
replacement,call 1 800 PCC–9125.
Plug one end of the power adapter into the jack labeled ADAPTER
on the back of the phone.
Telephone
Line Cords
Telephone Jacks
Modular
Telephone Jack
Lines 1 and 2
Modular
Telephone Jack
Lines 3 and 4
Power Cord
Standard
Electrical
Outlet
INSTALLATION
Standard
Electrical
Outlet
Modular
Telephone Jacks
Lines 1 and 2
Modular
Telephone Jacks
Lines 3 and 4
Telephone Jacks
Power CordTelephone
Line Cords
Lucent 0954 book.L1 5/7/98, 10:35 AM7
8
6 Mount the phone on the wall.
•Four One-Line Jacks
•Two Two-Line Jacks
NOTE: If you have three modular telephone jacks, mount the phone onto
a jack without a wall-mounting adapter. If you have four modular
telephone jacks, mount the phone onto a jack without a wall-mounting
adapter.
INSTALLATION
Modular
Telephone
Jack Line 1
Modular
Telephone
Jacks Lines
3 and 4 Telephone
Line Cord
Telephone
Line Cord
Standard
Electrical
Outlet
Modular
Telephone
Jack Line 2
Power Cord
Telephone
Line Cord
Standard
Electrical
Outlet
Modular
Telephone
Jack Lines
3 and 4
Modular
Telephone Jack
Lines 1 and 2
Power Cord
Lucent 0954 book.L1 5/7/98, 10:35 AM8
Otros manuales para 954
1
Tabla de contenidos
Otros manuales de Teléfono de Lucent Technologies
Lucent Technologies
Lucent Technologies INDeX 2030 Manual de usuario
Lucent Technologies
Lucent Technologies 4400 series Manual de usuario
Lucent Technologies
Lucent Technologies INDeX 2010 Manual de usuario
Lucent Technologies
Lucent Technologies 9630 Manual de usuario
Lucent Technologies
Lucent Technologies MERLIN LEGEND MDC 9000 Manual de usuario
Lucent Technologies
Lucent Technologies Merlin Legend MLX-5 Manual de usuario
Lucent Technologies
Lucent Technologies MDW 9040 Guía
Lucent Technologies
Lucent Technologies Definity 6408D+ Manual de usuario
Lucent Technologies
Lucent Technologies CALLMASTER Manual de usuario
Lucent Technologies
Lucent Technologies Definity 8410 Manual de usuario
Lucent Technologies
Lucent Technologies 6400 Series Manual de usuario
Lucent Technologies
Lucent Technologies Definity 8405 Manual de usuario
Lucent Technologies
Lucent Technologies 6225 Manual de usuario
Lucent Technologies
Lucent Technologies 4412D+ Manual de usuario
Lucent Technologies
Lucent Technologies Index Manual de usuario
Lucent Technologies
Lucent Technologies Voice Terminal 8405 Manual de usuario
Lucent Technologies
Lucent Technologies Merlin Communications System Manual de usuario
Lucent Technologies
Lucent Technologies MDW 9030P Guía de inicio rápido
Lucent Technologies
Lucent Technologies Definity 8434DX Manual de usuario
Lucent Technologies
Lucent Technologies ISDN 970 Manual de usuario
