Louroe Electronics ASK-4 122 Manual de usuario

The ASK-4® 122 is a two zone audio monitoring system designed to interface with a DVR, VCR or other recording device

that accept line level audio. The AP-2 Audio Base Station has 2 microphone inputs, contains a built-in 3’ speaker and

volume control for producing live audio and playback. It has loop out RCA output per microphone so each microphone

can be recorded individually. It also has a selectable audio output that produces audio to a recorder for that zone or

microphone selected. The Verifact™ A microphones are omnidirectional pre-amplified microphone that produces line level

audio output.

AUDIO MONITORING SYSTEM

INSTALLATION AND OPERATING INSTRUCTIONS

6955 VALJEAN AVE, VAN NUYS, CA 91406

PH: (818)994-6498 / FAX: (818)994-6458

/ www.louroe.com[email protected]

Page 1 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_122_inst_7/14

ASK-4 #122

AP-2 Base Station

Verifact™ A Microphones

Contents Description

1 AP-2 listed Audio Base Station.

Used for listening to live audio

from microphone, as well as

audio playback from DVR’s, VCR’s

or other audio devices.

2 Verifact™ A Microphone Line Level, Electret condenser

microphone with preamp. Picks up

normal sounds within 30’ circle.

May be located Up to 1000’ from

APR-1 Base Station.

1 AD-1 listed AC ADAPTER.

Supplies 12 Vdc to AP-2 and

Microphone.

1 Dual RCA Cable RCA cable for connection to a

DVR/VCR or other Audio devices

that accept line level input

(0dB @ 600W).

INSTALLATION AND OPERATING INSTRUCTIONS

Page 2 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_122_inst_7/14

DESCRIPTION AND FUNCTION OF PARTS

[1] - Play/Mute Switch Used when playing back audio from a recorder or mute the audio

from the microphone. No audio is heard on the Speaker[7] when

this switch is ON.

[2] - Zone Selector Switches Select zone for monitoring. Press switch of desired zone to listen

to live audio. Pressing more than one zone is possible when it is

necessary to monitor more than one zone at a time, but audio

may be difficult to understand if there is audio activity at several

zones. Zone switches light blue when press indicating active

zone.

[3] - Headset Jack Used for private listening. Any stereo headset with 8 to 600W

impedance maybe used. Mutes speaker output when use.

[4] - Power Indicator Lights (green) when power is turned ON.

[5] - Power-Volume Knob Rotating knob clockwise turns ON power to the unit as indicated

by the Power Indicator[4] light. Rotating further clockwise

increases the volume of the monitored audio as heard through

the Monitor Speaker[7].

Fig. 1 Front of AP-2

Fig. 1 Front view of AP-2

432

INSTALLATION AND OPERATING INSTRUCTIONS

Page 3 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_122_inst_7/14

Fig. 2 Rear view of AP-2

DESCRIPTION AND FUNCTION OF PARTS

[6] - Mic Input 3-Pin Terminal Block Connects to remote Louroe microphones.

[7] - Monitor Speaker Provides live audio through the 3” built-in speaker. Muted when

a headset is connected to Headset Jack[3].

[8] - Audio In Jack (RCA) Receives audio playback from DVR/VCR, etc. and is broadcast

through the built-in speaker. [7].

[9] - Audio Out Jack (RCA) Provides audio to DVR/VCR for recording or to other audio

devices accepting line level input when any of the Zone Selector

Switches[2] are activated or push in. The audio output to this

jack will be the audio selected by the Zone Selector Switches[2].

[10]- Power Jack Accepts 12Vdc from external power supply (included)

[11] - Mic Output Jack Used for connection to a DVR with multiple audio inputs or to a

soundcard module for audio recording. May also be used for

paralleling to a second Louroe audio base station.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 4 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_122_inst_7/14

MICROPHONE CONNECTIONS TO AP-2

A 12Vdc power supply is included with the above units. First connect the small end with the 90° plug to the above

unit’s Power Jack[10] and connect large end to a standard 120Vac outlet or power strip.

Maximum distance between AP-2, etc. and Louroe microphones is 1,000 ft. (305m)

CONNECTING AP-2 TO A RECORDING DEVICE (DVR, ETC.)

All Louroe Verifact™ Microphones contain a 3-pin terminal block marked A, B, C. All Louroe base stations contain similar

3-pin terminal blocks marked A, B, C. Refer to interconnection diagram p 5. Using sample cable:

A = 12Vdc Power (red wire)

B = Audio Output (black wire)

C = Common Ground (bare wire)

1) Take one end of recommended cable to first microphone location and connect:

Red wire to terminal A (12Vdc)

Black wire to terminal B (Audio Output)

Bare wire to terminal C (Ground)

2) Run other end of cable to the AP-2 Base Station location and connect to the Mic Input 3-Pin Terminal Block

of the audio zone in which the remote microphone is assigned (example zone 1). Again connect Red wire to

Pin A, Black wire to Pin B and Bare wire to Pin C.

3) Repeat the same procedure for the remaining microphones using the additional terminal blocks marked zone

2, zone 3, etc.

[6]

A) If connecting to a DVR with one audio input:

1) Connect an RCA cable to the Audio Out jack [9] of AP-2 and connect other end to Audio In (or line in)

of VCR/DVR

2) To record a particular zone, press the Zone Selector Switch [2] located on front panel of base station

for the audio zone to be recorded

3) For audio playback, connect another RCA cable from Audio Out (or line out) of VCR/DVR to Audio In

[8] of AP-2

4) Press in the Mute/Playback button[1] of front panel

5) Press the play or playback button on VCR/DVR to start audio playback. Playback will be broadcast

through the base station’s built-in Monitor Speaker[7]. As an alternate, playback may be channeled

through a CCTV monitor with amplifier or through DVR’s speaker system

2) If connecting to a DVR with multiple audio inputs or to a soundcard module:

AP-2 has 2 line level RCA Mic Output Jacks [11]

1) Connect RCA cables between the Mic Output Jacks [11] and Audio Inputs of DVR matching zone 1 to

channel 1 of the DVR audio inputs.

2) For audio playback from base station (AP-2), press in the Play/Mute Switch[1] located on base

station’s front panel. Playback may also be channeled through other audio sources

3) To select a specific audio zone for playback, refer to DVR’s instruction manual

APPLYING POWER TO THE AP-2

INSTALLATION AND OPERATING INSTRUCTIONS

Page 5 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_122_inst_7/14

INTERCONNECTION DIAGRAM FOR VERIFACT A MICROPHONE

AND AP-2 BASE STATION

ABCC

IN OUT

A B C

CBA

Red(A)

Black(B)

Bare(C)

Red(A)

Black(B) Bare(C)

Red(A)

Black(B)

Bare(C)

12Vdc

SELECTABLE

AUDIO OUTPUT

Use if recording device

has only one Audio Input

Use for audio playback

from recording device

WIRING REQUIREMENTS

VERIFACT A MICROPHONE

REAR OF AP-2 BASE STATION

2 Cond Shielded Cable

22 Gauge with a 24 Gauge

Drain wire.

2 Conductor shielded cable, 22

gauge with a 24 gauge drain wire

NOTE: Unshielded cable is not

satisfactory for audio systems

WIRING REQUIREMENTS

West Penn 452 or equivalent

SUMMARY

Please check that wiring and power connections conform to the above instructions. In the event of a malfunction or

problem with the product, factory assistance is available from 8:00 AM to 4:00 PM (Pacific Time) by calling (818) 994-

6498.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 6 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_122_inst_7/14

OPERATION AND TEST

After microphones and power supply are connected, proceed as follows:

1) Turn on power to the unit by rotating the Power-Volume Knob[5] clockwise to “ON” position. The green LED

[4] will illuminate, indicating power to the unit. Rotate Power-Volume Knob[5] further clockwise to increase

the volume of monitored audio.

2) Press Zone Selector Switch[2] marked zone 1. Audio from zone 1 should be present at the Monitor

Speaker[7]. The switch blue light should be ON indicating that zone is activated. If there is no audio, remove

wires connected to Mic Input 3-Pin Terminal Block[6] for zone 1 at the rear of the unit. With a DC voltmeter,

check that 12 Vdc is present at terminals “A” and “C”. If voltage is not present, unit has defective power

supply. If voltage is present, check to assure that wires are connected properly to the right terminals.

Otherwise microphone is defective. Call factory for assistance.

3) Repeat step 2 for the remainder of the zones.

4) When a recorder is connected to the unit, press Play/Mute Switch[1]. The Play/Mute Switch[1] will light. The

audio from the remote microphones are muted. Press DVR playback switch to listen to recorded audio on the

unit’s speaker. The Play/Mute Switch[1] must be depressed or in the “OUT” position to hear live audio again

on the Monitor Speaker[7].

INSTALLATION AND OPERATING INSTRUCTIONS

Page 7 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

SPECIFICATIONS - Verifact™ A

Frequency response

Output

Current drain

40 Hz to 15 kHz ± 1 dB

4 mA

Supply voltage 12 Vdc

Microphone housing High impact ABS

Dimensions US

Weight

4” "dia x 1 ½ H

(10cm dia x 3.8cm H)

0.5 Lb (0.2 Kg)

Line Level (0 dB @ 1000W)

metric

ask4_122_inst_7/14

SPECIFICATIONS - AP_2

Input impedance

(from remote mic)

100KW

Monitor power output 1W @ 8

Audio input impedance 10k

Freq. response 100 Hz to 10kHz

Power input 12 Vdc, 500mA

Dimensions 6 5/8"W x 8 5/8 x 2 1/8"H"L

Headphone impedance

Current Drain

8 to 600

200mA

Weight 1lb 12oz

Audio output impedance 1KW

MANUFACTURED

IN THE

IMPORTANT NOTICE

When this equipment is used as part of an

audio monitoring system, the law requires

that the public be given notice of AUDIO

MONITORING ON THE PREMISES. A

decal notice is included with each

microphone shipped.

Federal Law References:

Federal Regulations, US Code, Title 18.

Crime and Criminal Procedure, Sec 2510.

Page 8 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

WARRANTY

LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.

Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.

This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS .

This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation

instructions provided by LOUROE ELECTRONICS.

Returned shipments to LOUROE ELECTRONICS shall be at customer’s expense. LOUROE ELECTRONICS will return the equipment prepaid via best way.

AUDIO

MONITORING

These Premises

ask4_122_inst_7/14

Tabla de contenidos

Otros manuales de Sistema de altavoces de Louroe Electronics

Louroe Electronics

Louroe Electronics ASK-4 KIT #501 Manual de usuario

Louroe Electronics

Louroe Electronics LE-018 Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 304-DV Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 Manual de usuario

Louroe Electronics

Louroe Electronics APR-1 Manual de usuario

Louroe Electronics

Louroe Electronics LE-393 Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 101C Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 101-DV Instrucciones de funcionamiento

Louroe Electronics

Louroe Electronics ASK-4 300 Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 104 Manual de usuario

Louroe Electronics

Louroe Electronics LE-363 Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 # 304 Manual de usuario

Louroe Electronics

Louroe Electronics AP-4TB-RM Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 101 Manual de usuario

Louroe Electronics

Louroe Electronics VERIFACT L-DT Manual de usuario

Louroe Electronics

Louroe Electronics AP-2TB Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 501 Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 Guía del usuario

Louroe Electronics

Louroe Electronics ASK-4 Manual de usuario

Louroe Electronics

Louroe Electronics verifact agc Manual de usuario

Louroe Electronics

Louroe Electronics LE-019 Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 101B Manual de usuario

Louroe Electronics

Louroe Electronics Verifact DVGC Manual de usuario

Louroe Electronics

Louroe Electronics ASK-4 300 Manual de servicio

Manuales populares de Sistema de altavoces de otras marcas

JVC

JVC CA-MXK5R Manual de usuario

LG NB4532B Manual de usuario

JVC

JVC CA-FSH100 Manual de usuario

5Core

5Core Pro Series Manual de usuario

EAW

EAW MQV1394e Manual de usuario

Lynx

Lynx GXR-LA10A Manual de usuario

iLive

iLive ITB066B Manual de usuario

RDX

RDX QuickStation 4 Manual de usuario

Electro-Voice

Electro-Voice S-122 Manual de usuario

Sven

Sven SPS-619 GOLD Manual de usuario

Pioneer

Pioneer CS-7070 Manual de usuario

EAW

EAW UB82e Manual de usuario

Sondpex

Sondpex Active Speaker System and Digital Music... Manual de usuario

JVC

JVC NX-PN7 Manual de usuario

Marshall Amplification

Marshall Amplification AR-DM61-BT Manual de usuario

Yamaha

Yamaha NX-A01 - Speaker Sys Manual de usuario

SE Audiotechnik

SE Audiotechnik I-LINE Manual de usuario

Gemini

Gemini WRX-843 Series Manual de usuario