Louroe Electronics RN-2 Manual de usuario
rn-2 2/08
Model RN-2 is a audio mixer for combining two
microphones or two speaker/microphones into one
audio zone. It is mounted between the two
microphones and the Louroe base station or other
receiving equipment. Contains an adjustment
potentiometer for microphone balance control. The
RN-2 is phantom powered by the Louroe base station.
If the base station is not used and RN-2 is interfaced
directly with other equipment (VCR, etc.), then 12 Vdc
power must be applied to terminals A and C of either
the input or output terminal block of the RN-2.
NOTE: RN-2 is a mixer for combining two microphones or two speaker/microphones to
create a larger audio monitoring zone. Both microphones serve as one zone.
They are NOT on separate channels
WIRING REQUIREMENTS:
Microphone Only:
Louroe Verifact A, B, C, D, D-V, E, K or L-DT
Speaker Microphones:
Louroe Model TLI, TLM, TLMC, TLO, TLSP
E
LOUROE
LECTRONICS
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
RN-2
AUDIO MICROPHONE MIXER
INSTALLATION AND OPERATING INSTRUCTIONS
2 Conductor shielded cable, 22
gauge with a 24 gauge drain wire
NOTE: Unshielded cable is not
satisfactory for audio systems
WIRING REQUIREMENTS
West Penn 452 or equivalent
WIRING REQUIREMENTS
4 Conductor consisting of:
+
2 Conductor shielded, 20 gauge
with 22 gauge drain (microphone
connection)
+
2 Conductor unshielded, 18 gauge
(speaker connection)
All in the same jacket
West Penn 356 or equivalent
R
U
E
T
D
C
A
I
N
F
U
T
N
H
A
E
M
ELECTRICAL: WIRING CONNECTION FROM MICROPHONES TO RN-2
INPUT CONNECTIONS
I. Bring in wiring from first Louroe microphone (or speaker/microphone) to INPUT side of RN-2
and connect as follows:
1. Wire from terminal A of microphone goes to A of RN-2
2. Wire from terminal B of microphone goes to B1 of RN-2
3. Wire from terminal C of microphone goes to C of RN-2
If microphone includes a speaker, speaker wires connect as follows:
(a) Positive connection from speaker connects to SP terminal of RN-2
(b) Ground connection from speaker connects to C terminal of RN-2
II. Bring in wiring from second microphone (or speaker/microphone) to INPUT side of RN-2 and
connect as follows::
1. Wire from terminal A of second microphone goes to A of RN-2
2. Wire from terminal B of second microphone goes to B2 of RN-2
3. Wire from terminal C of second microphone goes to C of RN-2
If microphone includes a speaker, speaker wires are doubled up with first speaker at terminals C
and SP of INPUT side.
CONNECTING RN-2 TO LOUROE BASE STATION
From OUTPUT side of RN-2, make connection to the Louroe base station as follows:
1. Terminal A of output goes to terminal A of base station
2. Terminal B of output goes to terminal B of base station
3. Terminal C of output goes to terminal C of base station
4. If speakers are included, terminals C and SP from OUTPUT side connect with C and
SP of base station.
MICROPHONE BALANCE ADJUSTMENT
Located on the output side of the RN-2 Mixer is an adjustment potentiometer for microphone
balance. If more volume is desired from microphone connected to the B-1 input side, turn
potentiometer counterclockwise toward the B-1 arrow. If more volume is desired from microphone
connected to the B-2 input side, turn potentiometer clockwise toward the B-2 arrow. For equal
volume from the two microphones, position potentiometer to the center.
NOTE: DISTANCE BETWEEN MICROPHONE AND BASE STATION SHOULD NOT
EXCEED 1,000’. THE RN-2 MIXER GAIN IS LIMITED THAT IT MAY NOT
SATISFACTORILY DRIVE AN AUDIO LINE OF MORE THAN 1000’.
page 1 of 2
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
(818)
INSTALLATION OF RN-2
MECHANICAL:
RN-2 can be installed to a wall or flat surface with mounting screws or by using a strong double
backed adhesive tape. It is located between the microphones and the Louroe base station.
INSTALLATION AND OPERATING INSTRUCTIONS
rn-2 2/08
MICROPHONE
BALANCE CONTROL
B1 B2
QUICK REFERENCE INSTALLATION FOR
RN-2 MICROPHONE MIXER
MODEL RN-2 MIXER
MICROPHONE #2
TERMINAL BLOCK
TERMINAL BLOCK
MICROPHONE #1
TO INPUT OF LOUROE BASE STATIONS
(ALL MODELS)
WEST PENN 452
2 COND. SHIELDED
#22 AWG with #24 DRAIN
RN-2
LOUROE
EL ECT RO NI CS
MICROPHONE MIXER
TERMINAL BLOCK OF MODEL
A, B, C, D, D-VR, E, K, AND L-DT MICROPHONES
WEST PENN 452
2 COND. SHIELDED
#22 AWG with #24 DRAIN
A B C B2 SP1
A B C A B C
A B C SP
INPUT
OUTPUT
page 2 of 2
MICROPHONE
BALANCE
CONTROL
B1 B2
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
(818)
INSTALLATION AND OPERATING INSTRUCTIONS
rn-2 2/08
E
LOUROE
LECTRONICS
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
(818)
WARRANTY
LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.
Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.
This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS.
This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation
instructions provided by LOUROE ELECTRONICS.
Returned shipments to LOUROE ELECTRONICS shall be at customer’s expense. LOUROE ELECTRONICS will return the equipment prepaid via best way.
IMPORTANT NOTICE
When this equipment is used as part of an
audio monitoring system, the law requires
that the public be given notice of AUDIO
MONITORING ON THE PREMISES. A
decal notice is included with each
microphone shipped.
Federal Law References:
Federal Regulations, US Code, Title 18.
Crime and Criminal Procedure, Sec 2510.
AUDIO
MONITORING
E
LOUROE
LECTRONICS
On
These Premises
rn-2 2/08
Otros manuales de Mezclador de Louroe Electronics
