Loma Superscan Micro ISC Manual de usuario

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTERCANCEL

MENUS A to Z

Description:

The batch length is specified in hours, or optionally in the number of packs if a PEC is fitted. The

batch length represents the amount of production statistics that will be accumulated, before they are

transmitted down the serial link to a printer or computer, and then reset to zero.

Press the [ENTER] key, and then the [▲] and [▼] keys to adjust the batch length as necessary.

Scope:

00.00 to 24.00 for timed batch interval

0 to 9999 for pack batch interval

Default:

01.00 for time.

Notes:

Batch reports must be enabled in the Report Options menu for this menu entry to appear.

*BTCH LENTH 1.00

●

BATCH LENGTH

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTER

CANCEL

MENUS A to Z

Description:

This facility can be used to synchronise the start of the batch to a particular time of day. For example,

if hourly batch statistics are required starting from 6.30pm, then the Batch Length would be set to

1.00 hour and the Batch Start to 18.30 hours. This would mean that the batch statistics would be reset

and transmitted down the serial link every hour at half past the hour.

Press the [ENTER] key, and then the [▲] or [▼] keys to adjust the batch start time.

To turn the start time facility off, so that batch statistics are reset and transmitted at multiples of batch

lengths after the batch starts, set the start time to 00.00.

Scope:

00.00 to 24.00. 00.00 will disable this facility.

Default:

00.00

Note:

This menu entry will only appear when Batch Reports are enabled, and the batch units are in terms of

time.

*BTCH START 1.30

●

BATCH START

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTERCANCEL

MENUS A to Z

*BTCH UNITS PACKS

Description:

Press the [ENTER] key, and then the [▲] or [▼] key to select between time or packs for the batch

interval.

Scope:

TIME or PACK.

Default:

TIME.

Notes:

A photo eye (PEC) must be fitted if the batch interval is to be set in terms of the number of packs.

This menu entry will only appear when batch reports are enabled in the Report Option menu.

●

BATCH UNITS

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTER

CANCEL

MENUS A to Z

Description:

The date and time specified within this menu are used to time stamp the data in the contaminant, fault

and error logs, and also on the printed reports.

Press the [ENTER] key to gain access to the Calendar menu to setup the date and time.

Note:

The time of day is specified using the 24 hour clock.

CALENDAR

●

CALENDAR

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTERCANCEL

MENUS A to Z

Description:

Press the [CALIBRATE] key to move into the calibrate menu from any other menu position, from

where Full Calibration, Update Calibration or Man Setup can be accessed.

Note:

A calibration report will be transmitted down the serial link upon completion of a calibration cycle,

only if report is enabled in the serial link menu, and the calibration report is enabled in the Report

Options menu.

ANY DISPLAY

●

SAMPLE REPORT

---------------------------------------

: LOMA SUPERSCAN MICRO METAL DETECTOR :

---------------------------------------

CALIBRATION REPORT

Time : 15-32-16 Date : WED 20 SEP 1995

Product Number : 1

Product Identification : CHEESE

Machine Identification : MD12345

Working Mode : REACT

Working Mode Lock : YES

Minimum Threshold : 500

Maximum Threshold : 15000

Detection Threshold : 885

Product Compensation : -448

Head Power : MAX

Head Lock : NO

---------------------------------------

CALIBRATE

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTER

CANCEL

MENUS A to Z

Description:

In order to change the running product press the [CHANGE] key, then use the [▲] or [▼] to make

your selection. Finally, press the [ENTER] key for the selection to take effect.

Warning Messages:

+CHANGING TO+ This message is always displayed to indicate that a product change is

taking place. The new product name and number is displayed on the

next display.

+NOT CALIBRATED+ This message indicates that the selected product has never been

calibrated. To rectify this position go to the Product Setup menu and

make sure that the entries are correct before performing a full calibrate.

ANY DISPLAY

●

CHANGE PRODUCT

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTERCANCEL

MENUS A to Z

Description:

Press the [ENTER] key to clear the entries in the contaminant log.

CLEAR CONTAMS?

●

CLEAR CONTAMINANTS LOG

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTER

CANCEL

MENUS A to Z

CLEAR ERRORS?

Description:

Clearing a run error will turn the run error LED and Auxiliary relay off if it is configured for run error

indication, providing the error is no longer occurring. If the error is active, ie. still occurring, then the

run error will immediately come back putting the LED on.

Press the [ENTER] key to clear any run errors.

Notes:

Refer to the section on Error/Fault Logging for full details about run errors.

●

CLEAR ERRORS

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTERCANCEL

MENUS A to Z

Description:

Clearing a system fault will turn the system fault LED and Fault relay off, providing the fault is no

longer occurring. If the fault is active, ie. still happening, then the system fault will immediately come

back putting the fault LED and relay back on.

System faults are usually an indication of a serious malfunction with the equipment, and must

therefore be investigated promptly. Refer to the section on Error/Fault Logging for full details about

system faults, and what to do if you have one on your system.

Press the [ENTER] key to clear any system faults.

Notes:

On failsafe systems, the fault relay is typically wired into the conveyor or reject so that no product

can pass down the line in the event of a system fault.

Clearing the faults as described here will reset the LED fault indicator and the internal fault relay, but

the details in the fault log will not be cleared. These are maintained by the system for Loma Customer

Service Engineer reference.

CLEAR FAULTS?

●

CLEAR FAULTS

❍

❍❍❍

CALIBRATE

CHANGE RESULTS

RUN DETECT

CALIBRATE

SYSTEM FAULT

RUN ERROR

▼▲

I S C

L o m a S u p e r s c a n M i c r o

❍SETUP

ENTER

CANCEL

MENUS A to Z

Description:

This value is automatically derived during a calibration cycle, and should therefore not normally

require adjustment: only alter the value if advised to do so by a LOMA Service Engineer.

Press the [ENTER] key to view the compensation and signal level values; the [▲] and [▼] keys to

adjust the compensation value. The compensation value is displayed on the left hand side of the

display, and the signal level on the right hand side.

Scope:

-65535 to 65535

Notes:

This menu position is only accessible if the Manual Setup menu has been enabled in the User Options

menu.

The calibrate LED will illuminate whilst the compensation value is being adjusted.

For more information about what the compensation value does, please refer to the Principles of

Operation section.

COMPENSATION

●

COMPENSATION

Otros manuales para Superscan Micro ISC

Tabla de contenidos

Otros manuales de Detector de metales de Loma

Loma

Loma IQ + Manual del propietario

Loma

Loma IQ3+ Manual de usuario

Loma

Loma IQ2 Manual de usuario

Loma

Loma IQ3 Manual de usuario

Loma

Loma IQ3X Manual de usuario

Loma

Loma Superscan Micro Manual

Loma

Loma IQ2 Manual de usuario

Loma

Loma X5c Manual de usuario

Loma

Loma Superscan Micro ISC Manual de usuario

Loma

Loma IQ3+ST Manual de usuario

Manuales populares de Detector de metales de otras marcas

Garrett

Garrett MAGNASCANNER CS 5000 Manual de usuario

Valex

Valex 1800200 Manual de usuario

Gauss

Gauss MIL MD Manual de usuario

Velleman

Velleman CS130 Manual de usuario

Sears

Sears 321.596370 Manual de usuario

Eriez

Eriez X8 Manual de usuario

Steinberg Systems

Steinberg Systems SBS-MD-22 Manual de usuario

Zircon

Zircon MetalliScanner m60c Manual de usuario

nalanda

nalanda MD027 Manual de usuario

REV Ritter

REV Ritter CB-7005 Manual de usuario

Minelab

Minelab F1A4 Manual de usuario

Fisher Research Labs

Fisher Research Labs F70 Manual de usuario

Steinberg Systems

Steinberg Systems SBS-MD-12 Manual de usuario

GOLDEN MASK

GOLDEN MASK 5 Manual de usuario

Grizzly

Grizzly YM 203 Manual de usuario

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Manual de usuario

Treasure Cove

Treasure Cove Vibra-Probe 560 Manual de usuario

Accurate Locators

Accurate Locators XL16 IMAGER Manual de usuario