LOKERMANN GRAND ARC 400 CEL Manual de usuario

USER MANUAL

INVERTER Based Welding Machines

IMPORTANT: Read this OPERATOR MANUAL together

with PRESCRIPTION AND COMPLIANCE MANUAL before

to use this equipment. In case of loss one of two parts

contact immediately your dealer.

Allow the operator to consult this manual.

GRAND ARC

400 CEL

1 INSTALLATION WARNING

2 OVERVIEW

2.1 Features

2.2 Technical Data

2.3 Brief Introduction

2.4 Duty cycle and Over-heat

2.5 Working Principle

2.6 Volt-Ampere Characteristic

3 INSTALLATION & OPERATION

3.1 Layout for the front and rear panel

3.2 Installation & Operation for MMA Welding

3.2.1 Set up installation for MMA Welding

3.2.2 Operation for MMA Welding

3.2.3 MMA Welding

3.2.4 MMA Welding Fundamentals

3.2.5 MMA Welding trouble shooting

3.3 Installation & Operation for TIG Welding

3.3.1 Set up installation for TIG Welding

3.3.2 Operation for TIG Welding

3.3.3 TIG Welding Fundamentals

3.3.4 DC TIG Welding trouble shooting

3.4 Operation environment

3.5 Operation Notices

4 MAINTENANCE & TROUBLESHOOTING

4.1 Maintenance

4.2 Troubleshooting

4.3 List of error code

4.4 Electrical schematic drawing

1. Installation warning

This machine is certified according to 60974-10:2014 Arc Welding Equipment Part 10: Electromagnetic

compatibility (EMC) requirement and the EUT belongs to Group 2 Class A.

WARNING: This Class A equipment is intended for industrial use and it is not intended for use in

residential locations where the elctrical power is provided by the public low-voltage supply system.

There may be potential difficulties in ensuring electromagnetic compatibility in those locations, due to

conducted as well as radiated disturbances.

WARNING: This equipment does not comply with IEC 61000-3-12. If it is connected to a public low-

voltage system, it is the responsability of the installer or user of the equipment to ensure, by consultation

with the distribution network operator if necessary, that the equipment may be connected.

Assessment of area

Before installing arc welding equipment the user shall make an assessment of potential

electromagnetic problems in the surrounding area. The following shall be taken into account:

a) other supply cables, control cables, signalling and telephone cables, above, below and

adjacent to the arc welding equipment;

b) radio and television transmitters and receivers;

c) computer and other control equipment;

d) safety critical equipment, for example guarding of industrial equipment;

e) the health of the people around, for example the use of pacemakers and hearing aids;

f) equipment used for calibration or measurement;

g) the immunity of other equipment in the environment. The user shall ensure that other

equipment being used in the environment is compatible. This may require additional

protection measures;

h) the time of day that welding or other activities are to be carried out.

The size of the surrounding area to be considered will depend on the structure of the building

and other activities that are taking place. The surrounding area may extend beyond the

boundaries of the premises.

Methods of reducing emissions-Public supply system

Arc welding equipment should be connected to the public supply system according to this manual

recommendations. If interference occurs, it may be necessary to takeadditional precautions such as

filtering of the public supply system. Consideration should be given to shielding the supply cable of

permanently installed arc welding equipment, in metallic conduit or equivalent. Shielding should be

electrically continuous throughout its length. The shielding should be connected to the welding power

source so that good electrical contact is maintained between the conduit and the welding power

source enclosure.

Maintenance of the arc welding equipment

The arc welding equipment should be routinely maintained according to this manual

recommendations. All access and service doors and covers should be closed and properly

fastened when the arc welding equipment is in operation. The arc welding equipment should

not be modified in any way, except for those changes and adjustments covered in this manaul. In

particular, the spark gaps of arc striking and stabilising devices

should be adjusted and maintained according to our recommendations.

Welding cables

The welding cables should be kept as short as possible and should be positioned close

together, running at or close to the floor level.

Equipotential bonding

Bonding of all metallic objects in the surrounding area should be considered. However,

metallic objects bonded to the work piece will increase the risk that the operator could receive

an electric shock by touching these metallic objects and the electrode at the same time. The

operator should be insulated from all such bonded metallic objects.

Earthing of the workpiece

Where the workpiece is not bonded to earth for electrical safety, nor connected to earth

because of its size and position, for example, ship’s hull or building steelwork, a connection

bonding the workpiece to earth may reduce emissions in some, but not all instances. Care should be

taken to prevent the earthing of the workpiece increasing the risk of injury to users or damage to other

electrical equipment. Where necessary, the connection of the workpiece to earth should be made by

a direct connection to the workpiece, but in some countries where direct connection is not permitted,

the bonding should be achieved by suitable capacitance, selected according to national regulations.

Screening and shielding

Selective screening and shielding of other cables and equipment in the surrounding area may

alleviate problems of interference. Screening of the entire welding area may be considered for

special applications.

2 Overview

.1 Features



Capable of welding with Lift Tig Mode.



Designed for

using cellulose welding rods.



Selectable VRD Protection for increased safety.



Adjustable arc force, hot start & anti-stick for

greater control and ease of use .



Digital current display meter for accurate pre-

setting and feedback of welding param- eters &

output.



Phase loss protection prevents damage as

machine automatically shuts down if power

supply phase loss occurs.



Temperature, voltage and current sensors for

increased reliability & safety.



Light,weight and compact design, ideal for

portable applications



Designed to work with diesel generators and

to avoid failures due to its voltage spikes.



Power source wind tunnel cooling construction

for protection against environmental contamination

2.2 Technical Data

Models

Parameters

GRAND ARC 400 CEL

Power Supply Voltage (V) 3~380V/400V±10%

Frequency(HZ) 50/60

Rated input current(A) 38MMA/28 TIG

Rated input power（KW）16.1 MMA/11.7 TIG

Duty cycle (40℃10 min)60% 400A

100% 310A

Welding Current Range(A) 20-400

No Load Voltage(V) 94MMA/22 TIG

Efficiency(%) ≥80%

Power Factor 0.7

Insulation class H

Protection class IP23

Cooling

Net Weight(Kg) 22

Dimensions(mm)

570*280*450

Electrode Diameter

φ1.6~φ6.0

Electrode Type 6010,6011,6013,7018 etc.

Note: The above parameters are subject to change with future machine improvement!

.3 Brief Introduction

series of welding machines adopt the latest Pulse Width Modulation (PWM) technology

nd the Insulated Gate Bipolar Transistor (IGBT) power modules. It uses switching frequencies in

he 20KHz-50KHz ranges so as to replace the traditional line-frequency transformer type welding

achines. Thus, machines are characterized with portability, small size, lightweight, low energy

onsumption and noise, etc.

series of welding machines

has

excellent performance: constant current output makes

elding arc more stab le; fast dynamic response speed reduces the impact from the arc length

luctuation to the current; accurate stepless current adjustment and pre-setting function. There are als

ome automatic protection functions for under voltage, over current, over heat, etc. inside the welder

hen the problems listed before occurred, the alarm light on the front panel is on and at the same

ime the output current will be cut off. It can self-protect, prolong the us efull life, greatly improved

he reliability and pract icality of the welding machine.

MA series of welding machines can also realize TIG operation. While MMA operation, if the

lectrode touches workpiece over two seconds, the welding current will drop to the minimum curren

utomatically to protect the electro de. While TIG operation, the minimum current will be outputted

irstly until the arc is ignited by lifting method, the output current will rise to the preset value, which

an protect the electrode.

MA series of welding machines is widely used in Petroleum, chemical, mechanical,

hipbuilding, architecture, boiler, pressure container, military industry and Maintenance work, etc.

his machine has high duty cycle even in the 40℃, which can keep the continuous operation. The

rame is Stability of the machine,which can keep working under high temperature and corrosion

nvironment.

MMA: Manual Metal Arc welding;

PWM: Pulse-Width Modulation;

IGBT: Insulation Gate Bipolar Transistor;

TIG: Tungsten Inert Gas welding.

.4 Duty cycle and Over-heat

he letter “X” stands for Duty Cycle, which is defined as the portion of the time a welding machine

an weld continuously with it’s rated output current within a certain time cycle (10 minutes).

he relation between the duty cycle “X” and the output welding current “I” is shown as the right

igure.

f the welding machine is overheating, the IGBT over -heat protection sensing will send a signal to

he welding machine control unit to cut the output welding current OFF and light the over-heat pilot

amp on the front panel. In that case, the machine should not be welding for 10-15 minutes to cool

own with the fanrunning. When operating the machine again, the welding output current or the dut

ycle should be reduced.

.5 Working Principle

he working principle of MMA series of welding machines is shown in the following figure. Three-

hase 380V line frequency AC is rectified into DC, then is converted to medium frequency AC by

nverter device (IGB T), after reducing voltage by medium transformer (the main transformer) and

ectified by medium frequency rectifier (fast recovery diode), and is outputted by inductance filtering.

he circuit adopts current feedback control technology to insure current output stability. Meanwhile,

he welding current parameters can be adjusted continuously and steplessly to meet with the

equirements of welding craft.

.6 Volt-Ampere Characteristic

MA series of welding machines has excellent volt-ampere characteristic. Referring to the

ollowing graph. In MMA welding, the relation between the rated loading voltage U2and welding

urrent I2 is as follows:

When I2≤600A，U2＝20＋0.04 I2（V）；When I2＞600A，U2＝44（V）.

0 600 I

（A）

（V）

Working

point

Volt-ampere characteristic

The relation of the rated loading

voltage&welding current

Rectify Inverter

Medium

frequency

transformer

Medium

frequency

rectify

Hall device

Current positive-

feedback control

Three-phase, AC DC AC DC

380V，50Hz

AC DC

3 Installation & Operation

.1 Layout for the front and rear panel

（1）Negative (-) welding power output connection socket.

（2）Positive (+)

（3）Input power cable.

（4）Power switch: control the power Supply on and off.

（5）Welding current control knob.

（6）Digital current display meter.

（7）Power indicator: Lights when input power connected and machine switched on.

（8）Alarm indicator. *

（9）Welding output mode button: Sets power source in MMA, MMA VRD* or

Lift TIG* mode.

（10）MMA mode indicator.

（11）MMA VRD mode indicator.

（12）Lift TIG mode indicator.

（13）Arc Force control knob. *

（14）Hot Start control knob. *

*Denotes more detailed explanation of function to follow.

urther Controls Explained

larm indicator

ights when over voltage, over current, input phase loss or electrical overheating (due to

xceeding duty cycle) is detected and protection is activated.

hen protection is activated, welding output will be disabled until the safety system senses

he overload has reduced sufficiently and indicator lamp goes out. May also trigger if machine

xperiences an internal power circuit failure.

welding power output connection socket.

rc Force control knob

n MMA welding power source is designed to produce constant output current (CC). This mean

ith different types of electrode and arc length; the welding voltage varies to keep the current

onstant. This can cause instability in some welding conditions as MMAwelding electrodes will hav

minimum voltage they can operate with and still have a stable arc.

rc Force control boosts the welding power if its senses the welding voltage is getting too low. The

igher the arc force adjustment, the higher the minimum voltage that the power source will allow.

his effect will also cause the welding current to increase. 0 is Arc Force off, 10 is maximum Ar

orce. This is practically useful for electrode types that have a higher operating voltage requirement

r joint types that require a short arc length such as out of position welds.

ot Start control knob

ot start provides extra power when the weld starts to counteract the high resistance of the electrod

nd workpiece as the arc is started.

ift TIG Mode

ift TIG is an arc ignition system for basic TIG welding that removes the need to “scratch”

tart or strike the tungsten on the work piece to start the arc, which can have a negative effect on

he weld quality due to tungsten contamination. Lift arc starting works by gently touching the

ungsten on the work piece andthen lifting it off. The control circuit will sense whenthe tungsten

s removed from the work piece and send a pulse of electricity through the torch that will cause

he TIG arc to initiate.

RD Function

RD stands for Voltage Reduction Device. This is a safety system that reduces the output voltage

rom the welding terminals in MMA mode while the welding output is not in use, to reduce the risk

f electric shock from the live output voltage. The disadvantage of this system is that it makes the

triking of the arc more difficult, especially on restarts and with some types of electrode such as low

ydrogen electrodes.

.2 Installation & Operation for MMA Welding

3.2.1 Set up installation for MMA Welding

onnection of Output Cables Two sockets are available on this welding machine. For MMA weldin

he electrode holder is shown be connected to the positive socket, while the earth lead (work piece)

s connected to the negative socket, this is known as DCEP. However various electrodes require a

ifferent polarity for optimum results and careful attention should be paid to the polarity, refer to th

lectrode manufacturers information for the correct polarity.

CEP: Electrode connected to “+”output socket.

CEN: Electrode connected to“-”output socket.

(

1) Connect the earth lead to “-”,tighten clockwise;

(

2) Connect the earth clamp to the work piece. Contact with the work piece must be firm contact

with clean, bare metal, with no corrosion, paint or scale at the contact point.

(

3) Connect the electrode lead to “+”,tighten clockwise;

(

4) Each machine is equipped with a power cable should be based on the input voltage welding

power cable connected to the appropriate position, not to pick the wrong voltage;

(

5) With the corresponding input power supply terminal or socket good contact and prevent

oxidation;

(

6) With a multi meter measure the input voltage is within the fluctuation range;

(

7) The power ground is well grounded.

3.2.2 Operation for MMA Welding

(

1) According to the above method to install is correct, turn the power switch, so that the power

switch is “ON” position, then the power indicator light, the fan comes on, the device work

properly.

(

2) Select the MMA /MMAVRD function with the LIFT TIG/MMA/MMA VRD selector switch.

(

3) Set the welding current relevant to the electrode type and size being used as recommended by

the electrode manufacturer.

(

4) Set welding parameters (hot start and arc force) as required following instructions in the previou

section.

(

5) Place the electrode into the electrode holder and clamp tight.

(

6) Strike the electrode against the work piece to create and arc and hold the electrode steady to

maintain the arc.

(

7) Commence welding. If necessary, readjust the Weld Current control to obtain the welding

condition required.

(

8) After completion of welding the Power Source should be left turned ON for 2 to 3 minutes. Thi

allows the fan to run and cool the internal components.

(

9) Switch the ON/OFF Switch (located on the rear panel) to the OFF position.

Tabla de contenidos

Otros manuales de Sistema de soldadura de LOKERMANN

LOKERMANN

LOKERMANN GRAND MIG 351 MULTI SYN Manual de usuario

LOKERMANN

LOKERMANN GRAND CUT 60 Manual de usuario

LOKERMANN

LOKERMANN GRAND ARC 161 Manual de usuario

LOKERMANN

LOKERMANN GRAND TIG 250 DC PULSE Manual de usuario

LOKERMANN

LOKERMANN GRAND MIG 200 MULTI PFC SYN MV Manual de usuario

LOKERMANN

LOKERMANN GRAND PIPE 270 MULTI Manual de usuario

LOKERMANN

LOKERMANN GRAND CUT 40 PFC MV Manual de usuario

LOKERMANN

LOKERMANN GRAND MIG 315 COMPACT Manual de usuario

LOKERMANN

LOKERMANN GRAND MIG 400 PULSE Manual de usuario

LOKERMANN

LOKERMANN GRAND TIG 200 DC Manual de usuario

LOKERMANN

LOKERMANN Grand Tig 200 Manual de usuario

LOKERMANN

LOKERMANN GRAND MIG 160 Manual de usuario

LOKERMANN

LOKERMANN GRAND TIG 200 DC PFC MV Manual de usuario

LOKERMANN

LOKERMANN GRAND AIR HD Manual de usuario

LOKERMANN

LOKERMANN GRAND ARC 320 CEL PFC MV Manual de usuario

LOKERMANN

LOKERMANN GRAND CUT 41 COM Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario