Lode CORIVAL CPET Manual del operador

Interface sheet - Cosmed Omnia - Corival CPET

Service documentation

Lode BV

Zernikepark 16

NL 9747 AN Groningen

The Netherlands

t: +31 50 571 28 11

f: +31 50 571 67 46

@: ask@lode.nl

www.lode.nl

INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

33
33
44
4
4
5
66
6
7
7
88
1313
1717
1919
19
Table of contentsTable of contents
1 - List of symbols used1 - List of symbols used
2 - Validity2 - Validity
3 - Setup instructions - Cosmed Omnia3 - Setup instructions - Cosmed Omnia
3.1 - Cable Selection
3.2 - Software setup
3.3 - Ergometer Setup
4 - Setting up the hardware4 - Setting up the hardware
4.1 - Connection overview
4.2 - Connecting with the usb cable
4.3 - Connecting with the RS232 cable
5 - Treadmill or ergometer with 3.5" touch screen unit5 - Treadmill or ergometer with 3.5" touch screen unit
6 - Treadmill or ergometer with 7" touch screen control unit6 - Treadmill or ergometer with 7" touch screen control unit
7 - Nummerical Control Unit - Treadmill only7 - Nummerical Control Unit - Treadmill only
8 - Treadmill or Bicycle without control unit8 - Treadmill or Bicycle without control unit
8.1 - Device without control unit

1 - List of symbols used1 - List of symbols used

2 - Validity2 - Validity

The Cosmed Omnia software is a general software package that supports control of different Cosmed

products. The current supported products are:

- Quark CPET

- K5

- Quark RMR

- Quark PFT

This interface form covers the following Lode products:

* All Corival ergometers starting with serialnumber 9609xx-20150001

If your treadmill or ergometer is not covered by this interface form please contact Lode service

service@lode.nl

3/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

3 - Setup instructions - Cosmed Omnia3 - Setup instructions - Cosmed Omnia

3.1 - Cable Selection3.1 - Cable Selection

The required cable is a straight

RS232 cable (Lode art. nr.

930911) or USB A-to-B cable

(Lode art. nr. 930916)

Connect the cable to the

ergometer as described in

chapter "Hardware setup".

Connect the other end of the

Cable to the Cosmed Quark on

the AUX RS232 port (no.17 in

picture) if you are using an

RS232 cable or connect the USB A-to-B cable directly to the computer when using the USB A-to-B cable.

In case you are using the Cosmed K5 you may connect the RS232 or USB A-to-B cable to the computer

directly.

3.2 - Software setup3.2 - Software setup

Select COSMED device to use for

the test (Main menu > Utility >

DeviceManager)

4/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

Start a new ergo test, after

selecting a subject, and choose

the 'Lodebike' for ergometer.

When the ergometer is directly

connected to the computer you

can select a COM port number

on which the ergometer is

connected to the computer.

When using Cosmed Quark you

can select 'Metabolic card' for

the port selection.

Press OK to confirm and start a

test. Make sure the ergometer is

set up correctly before pressing OK. The procedure is explained in the next chapters.

3.3 - Ergometer Setup3.3 - Ergometer Setup

The following protocol needs to be set in the Lode ergometer to communicate with the external

equipment.

Bicycle ergometer: Lode Protocol

The next chapters describe the procedures to setup these protocols depending on the type of

ergometer.

5/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

4 - 4 - Setting up the hardwareSetting up the hardware

Lode ergometers have two ways of connecting external devices. The cable selection depends on the

connection possibilities of the external device. The previous chapter tells you which cable you need. This

can be a RS232 cable or a USB cable.

4.1 - 4.1 - Connection overviewConnection overview

Connect the cable to the USB

port if you are using a USB

cable.

Please note that you may have

to install the FTDI driver on the

external equipment. This

procedure is only needed if

windows fails to instal the driver

automatically.

You can find the driver on the

Lode website under the Services

tab.

Locations:

- For the Treadmill the communication ports are Located on the front side near the power switch.

- For the bicycle ergometer the communication ports are located on the bottom of the bicycle. Tilt the

ergometer on it's side to be able to acces these ports.

Communication Module:

Use the single RS232 port to connect the communication module to the external equipment.

Legacy communication card (picture above -> 1 * USB, 2 * RS232)

In case you are using a RS232 cable you must use the RS232 port closest

to the USB connector, on the picture indicated with RS232 (1).

6/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

4.2 - Connecting with the usb cable4.2 - Connecting with the usb cable

If there is no other connection available you can also use a USB cable to

connect.

1. You will need an USB A to B cable (Lode part no. 930916) to establish

communication between the Lode ergometer and your stress system or

ergospirometrysystem. See picture left.

2. Connect the cable to the Lode ergometer.

3. Connect the cable to the external device.

4.3 - Connecting with the RS232 cable4.3 - Connecting with the RS232 cable

Connecting with the RS232 cable

1. Depending on the external device you may need to use a straight

RS232 cable (Lode part no. 930911) or a cross linked cable. The cable

selection chapter specifies which cable is needed.

2. Connect the cable to the Lode ergometer.

3. Connect the cable to the external device.

7/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

5 - Treadmill or ergometer with 3.5" touch screen unit5 - Treadmill or ergometer with 3.5" touch screen unit

Start the Lode ergometer.

During start up information

about the ergometer, like the

kind of device, the serial

number and the connected

modules is displayed.

After initialisation the terminal

mode is automatically

displayed. Swipe with your

finger over the screen as

indicated with the red arrow in

the picture to go to the main

menu.

8/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

Select "Settings" to change

settings of the device.

You can choose your Language

in the "Language" menu. The

menu "Sleep Mode" sets a

screensaver. The menu

"Terminal Settings" lets you set

the communication settings for

external communication. The

menu "Service" is only intended

for service purposes to be

executed by factory trainend

personel.

Select "Terminal Settings" to

change the communication

protocol.

9/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

Select the Communication

protocol as desribed in

"Ergometer setup" chapter.

Select "Default" for the

baudrate.

10/22INTERFACE SHEET - COSMED OMNIA - CORIVAL CPET / VERSION: 1.0 - 2016-11-29

Tabla de contenidos

Otros manuales de Rueda de andar de Lode

Lode

Lode Valiant 2 cpet Manual de usuario

Lode

Lode Valiant 2 Rehab Manual de usuario

Lode

Lode ERGOMETERS Manual de usuario

Lode

Lode Valiant Ultra Manual de usuario

Lode

Lode Katana Sport Manual de usuario

Lode

Lode Edan EC-12 EXPRESS Manual del operador

Lode

Lode OEM Manual de usuario

Lode

Lode Schiller AT-10 Manual del operador

Lode

Lode Valiant 2 Pediatric Manual de usuario

Lode

Lode Valiant Ultra Manual de usuario

Lode

Lode Katana Manual de usuario

Lode

Lode Valiant Manual de usuario

Lode

Lode Edan ST-1212 Stress Manual de usuario

Manuales populares de Rueda de andar de otras marcas

Treadly

Treadly TREADLY 2 Manual de usuario

HEALTH ONE

HEALTH ONE Walk Ro Manual de usuario

NordicTrack

NordicTrack NTL12941 Manual de usuario

NordicTrack

NordicTrack T7.5 S Manual de usuario

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Manual de usuario

Merax

Merax MS282992 Manual de usuario

FYTTER

FYTTER RU-2SX Manual de usuario

Precor

Precor 903 Manual de usuario

FitLogic

FitLogic freewill d225 Manual de usuario

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Manual de usuario

Horizon Fitness

Horizon Fitness Adventure 5 Plus Manual de usuario

Stamia

Stamia InMotion II Manual de usuario

Smooth Fitness

Smooth Fitness EVO 3i Manual de usuario

NordicTrack

NordicTrack NETL81810.0 Manual de usuario

Schwinn

Schwinn 830/Journey 8.0 Manual de usuario

Keys Fitness

Keys Fitness HealthTrainer HT-740T Manual de usuario

Spirit

Spirit XT8 Manual de usuario

NordicTrack

NordicTrack T 14.0 Treadmill Manual de usuario