LIVARNO LUX 277939 Especificaciones técnicas

HALOGEN CEILING LIGHT

IAN 277939

HALOGÉNOVÉ STROPNÉ SVIETIDLO

Pokyny pre montáž, obsluhu a bezpečnostné pokyny

HALOGEN-DECKENLEUCHTE

Montage-, Bedienungs- und Sicherheitshinweise

HALOGENOVÉ STROPNÍ SVÍTIDLO

Pokyny k montáži, obsluze a bezpečnostní pokyny

HALOGEN CEILING LIGHT

Assembly, operating and safety instructions

HALOGÉN MENNYEZETI LÁMPA

Szerelési, használati és biztonsági tudnivalók

GB Assembly, operating and safety instructions Page 5

HU Szerelési, használati és biztonsági tudnivalók Oldal 11

CZ Pokyny k montáži, obsluze a bezpečnostní pokyny Strana 17

SK Pokyny pre montáž, obsluhu a bezpečnostné pokyny Strana 23

DE/AT/CH Montage-, Bedienungs- und Sicherheitshinweise Seite 31

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

device.

Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a készülék minde-

gyik funkcióját.

Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

14119602L

1114 15

1310

ca./approx.

90 mm

ca./approx.

190 mm

ca./approx.

670 mm

12 10 11

1 2 3

14107002L

5GB

Table of contents

List of pictograms used........................................................................................................Page 6

Introduction...................................................................................................................................Page 6

Intended use........................................................................................................................................Page 6

Scope of delivery................................................................................................................................Page 6

Parts description..................................................................................................................................Page 7

Technical Data ....................................................................................................................................Page 7

Safety.................................................................................................................................................Page 7

Safety notices......................................................................................................................................Page 7

Preparation...................................................................................................................................Page 8

Required tools and material ...............................................................................................................Page 8

Prior to installation.................................................................................................................Page 8

Start-up .............................................................................................................................................Page 8

Mounting the light...............................................................................................................................Page 8

Directing the spotlight.........................................................................................................................Page 9

Replacing lamps..................................................................................................................................Page 9

Maintenance and Cleaning..............................................................................................Page 9

Disposal............................................................................................................................................Page 10

Warranty and Service..........................................................................................................Page 10

Warranty Declaration.........................................................................................................................Page 10

Service address...................................................................................................................................Page 10

Declaration of Conformity..................................................................................................................Page 10

Manufacturer.......................................................................................................................................Page 10

6 GB

Introduction Introduction/Safety

Halogen ceiling light

Introduction

Congratulations on your new product.

You have selected a high quality prod-

uct. Please be sure to carefully read the

complete operating instructions. Fold out the page

with the illustrations. These instructions are part of

the product and contain important information on

setup and handling. Always follow all safety in-

structions. Before using this product for the ﬁrst time

verify the correct voltage and that all parts are

properly installed. Should you have any questions

or you are unsure about operating the product,

please contact the dealer or service centre. Please

keep these instructions in a safe place and pass

them on third parties as applicable.

Intended use

This light is only suitable for indoor use

in dry and enclosed spaces. The light

can be fastened to any normally inﬂam-

mable surface. This product is intended for private

household use only.

Scope of delivery

Check immediately after unpacking that the parts

are complete and that the product is in proper

condition.

1 Halogen ceiling light 4 ﬂame

4 Halogen light bulb, G9, 28W

4 Glass lampshades (14119602L)

1 Tool (14119602L)

4 Wire mesh balls (14107002L)

2 Screws (ceiling mounting)

2 Wall plugs (ceiling mounting)

List of pictograms used

Please read the operating instructions! Caution! Risk of electric shock!

This light is only suitable for indoor use

in dry and enclosed spaces. Caution - Hot surfaces!

Watt (eﬀective power) 0.5 m

RISK OF FIRE! Install the light

at least 0.5m from the items to

be illuminated.

Hertz (mains frequency) Do not use cold light lamps with

reﬂectors

Volt (AC) Only use halogen light bulbs

with a cover plate or low pres-

sure technology.

Earth conductor For your safety

Observe warnings and safety

notices!

Dispose of the packaging and

product in an environmental-

ly-friendly manner!

7GB

Introduction Introduction/Safety

2 Protection tubes (connection housing casing)

1 Set of assembly instructions and instructions for use

Parts description

1Wall plug

2Mounting bracket

3Locating screws (connection housing)

4Screws (mounting bracket)

5Connection housing

6Spotlight

7Terminal block

8Protective tube

9Mains connection cable (external)

10 Light bulb

11 Socket thread

12 Wire mesh ball (14107002L)

13 Lampshade (glass) (14119602L)

14 Tool (14119602L)

15 Silicone ring (14119602L)

16 Lamp ring (14119602L)

Technical Data

Item no.: 14119602L/14107002L

Operating voltage: 230-240V~50Hz

Light bulb: Halogen light bulb G9, 28W

Rated power: 4 x 28W

Protection class: I

Protection type: IP20

Safety

Safety notices

Damage due to failure to comply with these operat-

ing instructions will invalidate the guarantee! We

assume no liability for consequential damage! We

assume no liability for material damage or personal

injury due to improper handling or failure to

comply with the safety instructions!

Avoid the risk of fatal injury

from electric shock

Ensure that a qualiﬁed electrician, or a person

trained to carry out electrical installations,

performs the electrical installation.

Always check the light, power supply, and

mains cable for damage before plugging it in.

Never use the light if it shows any signs of

damage.

A damaged mains cable indi-

cates a life-threatening danger due to electric

shock. In the event of damage, repairs or other

problems with the light please contact the

service centre or a qualiﬁed electrician.

Prior to installation, remove the fuse or switch

oﬀ the circuit breaker (0 setting) in the fuse box.

Prior to installation verify the mains voltage on

site corresponds with the operating voltage

required for the light (see "Technical Data").

Ensure that the light does not come into contact

with water or other liquids under any circum-

stances.

Never open any of the components of the elec-

trical equipment or insert any objects into the

same components. This will pose a risk of fatal

injury from electric shock.

Do not install the light on a wet or conductive

substrate!

Prevent fire and

injury hazards

RISK OF INJURY! Check each lamp and

lamp glass for damage immediately after un-

packing.

Do not mount the light with defective lamps

and/or lamp lenses. In this case contact the

service centre for a replacement.

CAUTION! RISK OF BURNS

DUE TO HOT SURFACES! Ensure

that the luminaire has been switched

oﬀ and has cooled before touching it, to avoid

burn injuries. Lamps develop a lot of heat in the

area of the lamp head.

Allow the lamp to cool oﬀ completely.

8 GB

Start-up/Maintenance and CleaningSafety/Preparation/Prior to installation/Start-up

Replace defective bulbs with new ones immedi-

ately. Before changing bulbs, always ﬁrst re-

move the fuse or switch oﬀ the circuit breaker.

0.5 m

FIRE HAZARD! Fit the light so that

it is at least 0.5m away from the

material to be illuminated. Excessive

heat can result in a ﬁre.

Do not leave the light or packaging material

lying unattended. Plastic ﬁlm or bags, plastic

parts, etc. can be dangerous for children to

play with.

J Do not use cold light lamps with

reﬂector.

Only use halogen light bulbs with

cover glass or low-pressure

technology.

Safe working

Only use the light bulbs speciﬁed in chapter

"Technical Data".

Mount the light so that it is protected from

moisture and dirt.

Carefully prepare for assembly and allow your-

self adequate time. Organise all parts and any

necessary additional tools or materials before

starting so they are easy to reach.

Always be attentive! Always pay attention to

what you are doing and use common sense.

Never install the light if you are having diﬃ-

culty concentrating or do not feel well.

Preparation

Required tools and material

The tools and materials speciﬁed are not included.

This information and these values are non-binding

and are only provided as a reference.

The nature of the material is determined by the

individual local conditions.

- Pencil/making tool

- Voltage tester

- Screwdriver

- Electric drill

- Bit (ø approx. 0.6cm)

- Side cutting pliers

- Ladder

Prior to installation

Important: The electrical connection must be

established by a qualiﬁed electrician or a person

trained to perform electrical installations. This per-

son must be familiar with the properties of the light

and the connection regulations.

Familiarise yourself with all the instructions and

diagrams in this manual, as well as with the light

itself, before you install it.

Before installation ensure that the circuit, to which

the light will be connected, is not energised. To

do so, remove the fuse or switch oﬀ the circuit

breaker in the fuse box (0 position).

Use the voltage tester to verify the de-energised

status.

Start-up

Mounting the light

Remove the locating screws 3visible at the

side of the connection housing 5and remove

the mounting bracket 2at the back.

Use the slotted holes for the screws 4on the

mounting bracket 2to mark the drill holes.

Be careful not to damage the supply line.

Now drill the mounting holes (approx. 6mm,

approx. 40mm deep).

Insert the wall plugs 1into the drill holes.

Fasten the mounting bracket 2with the

screws 4provided.

Feed the mains connection cable (external) 9

through the protective tube 8.

Now connect the connection housing for the

light to the mains connection cable (external) 9

using the terminal block 7.

9GB

Start-up/Maintenance and Cleaning

Also ensure to connect the correct coloured

wires (live wire, black or brown = symbol L,

neutral wire, blue = symbol N).

Now connect the earth conductor (green-yellow)

to the designated terminal inside the con-

nection housing 5.

Now use the locating screws 3to connect the

light to the mounting bracket 2.

Item no. 14119602L:

Unscrew the lamp ring 16 from the bulb socket

11 .

ATTENTION: Do not lose the silicone ring 15 .

Place the lamp glass 13 over the bulb socket 11 .

Place the silicone ring 15 over the lamp ring 16 .

Use the tool 14 to secure the lamp glass 13

and the lamp ring 16 .

Use a clean, lint-free cloth when inserting the

light bulb 10 .

Carefully install the light bulb 10 in the socket.

Verify it is seated correctly.

Item no. 14107002L:

Use a clean, lint-free cloth when inserting the

light bulb 10 .

Carefully install the light bulb 10 in the socket.

Ensure that it is positioned correctly.

Carefully screw the wire mesh balls 12 onto

the socket threads 11 on the spotlight 6, turn-

ing to the right. Be careful not to damage the

light bulb 10 .

Replace the fuse or switch on the circuit

breaker in the fuse box (I position). Your light is

now ready to use.

Directing the spotlight

Only change the direction of the spotlights 6

when the light is switched oﬀ.

Allow the light to cool down completely.

Turn the individual spotlights 6on the base in

the desired direction. The spotlights can be

turned approx. 320°.

Replacing lamps

RISK OF ELECTRIC SHOCK!

First disconnect the light from the mains when re-

placing the lamp. To do so, remove the fuse or

switch oﬀ the circuit breaker in the fuse box

(position 0).

Allow the lamp to cool oﬀ completely.

Use a clean, lint-free cloth to replace a bulb.

Item no. 14119602L:

Carefully remove the defective light bulb 10

from the socket.

Carefully insert the new light bulb 10 in the

socket.

Item no. 14107002L:

Use a clean, lint-free cloth when inserting the

light bulb 10 .

Carefully unscrew the wire mesh ball 12 from

the bulb socket of the spotlight 6, turning to

the left.

Carefully remove the defective light bulb 10

from the socket. Carefully install a new light bulb

10 in the socket. Ensure that it is positioned

correctly.

Then carefully screw the wire mesh ball 12 onto

the socket thread of the spotlight 6, turning to

the right. Be careful not to damage the light

bulb 10 .

Ensure that it is properly positioned.

Replace the fuse or switch on the circuit

breaker in the fuse box (I position). Your light is

now ready to use.

Maintenance and Cleaning

RISK OF ELECTRIC SHOCK!

Disconnect the light from the mains circuit before

cleaning. To do so, remove the fuse or switch oﬀ

the circuit breaker in the fuse box (0 position).

RISK OF ELECTRIC SHOCK!

For electrical safety, never clean the light with

water or other liquids, or immerse it in water.

Safety/Preparation/Prior to installation/Start-up

10 GB

Maintenance and Cleaning/Disposal/Warranty and Service

CAUTION! RISK OF BURNS DUE TO HOT

SURFACES! Allow the light to cool completely.

Do not use solvents, benzene or similar

substances. They could damage the light.

Only use a dry, lint-free cloth for cleaning.

Replace the fuse or switch on the circuit

breaker in the fuse box (I position). Your light is

now ready to use.

Disposal

The package and packaging materials

consist entirely of environmentally

friendly materials. They can be disposed

of at your local recycling facility.

The symbol of the wheelie bin with the

line through it indicates within the Euro-

pean Union, this product must be disposed

of through separate refuse collection. This applies

to the product and to all components bearing this

symbol. Do not dispose of products bearing this

symbol in your normal household waste, but instead

they must be taken for recycling to a collection site

for electrical and electronic appliances. Recycling

helps to reduce the consumption of raw materials

and protects the environment.

Warranty and Service

Warranty Declaration

You receive a 36 month warranty on this product,

valid from the date of purchase.

The device has been carefully produced under

strict quality control.

Within the warranty period we shall rectify without

charge all material and manufacturing defects. In

the event of a defect arising during the warranty

period, please send the device to the listed Service

Centre address, making reference to the following

article number: 14119602L/ 14107002L.

Wear parts (such as bulbs) and damage caused

by improper handling, non-observance of the oper-

ating instructions or unauthorised interference are

excluded from the warranty.

The performance of services under the warranty do

not extend or renew the warranty period.

Q Service address

Briloner Leuchten GmbH

Im Kissen 2, DE-59929 Brilon, GERMANY

Tel.: +49 (0) 29 61/9712–800

Fax: +49 (0) 29 61/97 12–199

E-Mail: [email protected]

www.briloner.com

IAN 277939

Please have your receipt and the product number

(e.g. IAN 12345) available for all queries as proof

of purchase.

Q Declaration of Conformity

This product fulﬁls the requirements of the applicable

European and national directives. Conformity has

been demonstrated. The relevant declarations and

documents are held by the manufacturer.

Manufacturer

Briloner Leuchten GmbH

Im Kissen 2

DE-59929 Brilon

GERMANY

Tartalomjegyzék

Otros manuales para 277939

Tabla de contenidos

Idiomas:

Otros manuales de Iluminación del hogar de LIVARNO LUX

LIVARNO LUX

LIVARNO LUX 103994-14-01 Manual de usuario

LIVARNO LUX

LIVARNO LUX 93673 Manual de usuario

LIVARNO LUX

LIVARNO LUX 55616 Manual de usuario

LIVARNO LUX

LIVARNO LUX 288511 Manual de usuario

LIVARNO LUX

LIVARNO LUX 90547 Manual de usuario

LIVARNO LUX

LIVARNO LUX Z31172A Manual de usuario

LIVARNO LUX

LIVARNO LUX 113907 Manual de usuario

LIVARNO LUX

LIVARNO LUX 14120806L Especificaciones técnicas

LIVARNO LUX

LIVARNO LUX 14138204L Manual de usuario

LIVARNO LUX

LIVARNO LUX 14100308L Manual de usuario

LIVARNO LUX

LIVARNO LUX 54972 Especificaciones técnicas

LIVARNO LUX

LIVARNO LUX 14135306L Manual de usuario

LIVARNO LUX

LIVARNO LUX 274111 Manual de usuario

LIVARNO LUX

LIVARNO LUX Z31206A Manual de usuario

LIVARNO LUX

LIVARNO LUX 2973-010L Manual de usuario

LIVARNO LUX

LIVARNO LUX 14103106L Manual de usuario

LIVARNO LUX

LIVARNO LUX 277939 Especificaciones técnicas

LIVARNO LUX

LIVARNO LUX 14131008L Especificaciones técnicas

LIVARNO LUX

LIVARNO LUX 285632 Manual de usuario

LIVARNO LUX

LIVARNO LUX 114388 Manual de usuario

LIVARNO LUX

LIVARNO LUX 276248 Manual de usuario

LIVARNO LUX

LIVARNO LUX 290224 Manual de usuario

LIVARNO LUX

LIVARNO LUX 14115302L Manual de usuario

LIVARNO LUX

LIVARNO LUX 101510 Manual de usuario

Manuales populares de Iluminación del hogar de otras marcas

JONATHAN Y

JONATHAN Y JYL5019A Manual de usuario

JONATHAN Y

JONATHAN Y JYL6007A Manual de usuario

Philips

Philips Ledino 31606/11/16 Manual de usuario

Salus

Salus UG600 Manual de usuario

Safavieh Lighting

Safavieh Lighting CANDRI TBL4427A Manual de usuario

Hunter

Hunter Bullet Spotlight Kit Manual de instrucciones

Philips

Philips Ledino 16811/87/16 Manual de usuario

Philips

Philips 405441213 Manual de usuario

Philips

Philips Halogen Light Manual de usuario

Pentair

Pentair GLOBRITE Manual de usuario

Philips

Philips 55592-30-16 Manual de usuario

Livoo

Livoo Night light Manual de usuario

Schwaiger

Schwaiger NFL45 Manual de usuario

FRITZ HANSEN

FRITZ HANSEN AQ01 PLUG-IN Manual de usuario

MOOD

MOOD CORSIN JY-16 Manual de usuario

Safavieh Lighting

Safavieh Lighting KREMP TBL4409A Manual de usuario

JONATHAN Y

JONATHAN Y JYL8019 Manual de usuario

XTRASUN

XTRASUN XTDEOKT1 Manual de usuario