Litelink ACC-1004-XLR Manual de usuario
WARRANTY
All fiber optic transmission systems, products and accessories
manufactured by Liteway, Inc. and its subsidiaries are fully tested
prior to shipment and are warranted against defective materials
and workmanship for a period of five full years from the date of the
original shipment. Should a problem occur, a Return Material
Authorization Number (RMA) must be obtained from Liteway Inc.
at (516) 931-2800 and the item returned to Liteway, Inc. 166
Haverford Road, Hicksville, NY 11801, USA, prepaid. Liteway Inc.
will then, at its option repair or replace the defective item.
Liteway, Inc. maximum liability under this warranty is limited to the
cost of the defective item only. No contingent liabilities of any kind
are either assumed or implied.
Any items returned to Liteway, Inc. that have been misused,
abused, damaged, modified, connected or adjusted in any way
contrary to the instructions furnished by Liteway, Inc. or repaired
by unauthorized personnel will not be covered by this warranty.
Any non-warranty repairs required will be quoted at the current
rate for such services.
Important Notices
CAUTION ! AVOID DIRECT EXPOSURE TO BEAM.
Some -7,-8, and -9 models use laser diodes. These solid-state
laser diodes are located in the optical ports of these units. Laser
diodes produce invisible radiation that may be harmful to human
eyes. Never look directly into the optical port of any fiber optic
unit designed to operate with single-mode optical fiber.
NOT FOR LIFE SUPPORT SYSTEMS
Liteway, Inc. does not authorize or warrant any of its products or
accessories for use in critical life support systems or applications
of any kind.
© Copyright 2021 Liteway, Inc. 107744 Rev K
OPERATING INSTRUCTIONS
Amplified Intercom Speaker
Model ACC-1004
Model ACC-1004-XLR
Technical Specifications
Audio Output Level 15 watts maximum
Audio Output Distortion 10% or less at full output
Operating Current 1.5 Amps at full output, 0.2A standby
Input Voltage 10 to 16 Volts DC
Temperature Range 0º to 50ºC
Physical Size (mm) 4.5”(115)H x 5.5”(139)W x 2.5”(63.5)D
Input Impedance 3 to 16 Ohms
Input Audio Level 1.5 VPP max
Power input fuse 2 Amps
All specifications are subject to change without prior notice.
!
Power Terminal Block
Inside the INCX-4001
PS-1230US
Power Supply
(12 VDC @ 3 A)
ACC-1004
10 Watt Amplifier
Audio
+-
Red
Red
Black
Black
Operating Instructions
Description
The ACC-1004 and ACC-1004-XLR are amplified extension speakers
that are designed to provide more than 10 watts of audio output when
connected to the INCX-4001 or INCX-4101 intercom stations. These
amplified speakers are useful for increasing audio output level in
noisy locations.
Both speakers use an integrated circuit amplifier to provide the
necessary gain to raise the output audio level and a DC voltage
power source of 10 to 16 volts at 1.5 amps is required to provide
proper power for the units. In the case of the ACC-1004 stripped and
tinned DC power leads are provided with an in-line fuse holder
containing a two-amp fuse for short circuit or overload protection. In
the case of the ACC-1004-XLR a power connector and an in-line fuse
holder for use with the INCX-4101 are also provided. Both units are
protected from accidental reverse polarity of the power leads.
INSTALLATION:
1. Locate the amplified speaker indoors or in an area free from
direct exposure to weather.
2. Plug the audio connector into the matching connector inside the
INCX-4001 (Note that this connector is labeled “AMPLIFIER”) or
on the appropriate connector outside the INCX-4101 housing.
Connections to INCX-4001 Connections to INCX-4101
Either power connector may be used
107744 Rev K
3. Connect the power leads from the ACC-1004 to a 10 to 16 volts
DC power supply capable of providing at least 2 amperes. This
same power supply may be used to power the INCX-4001
Intercom Station if desired. The diagram below shows how to
power the AC-1004 and INCX-4001 from the same supply.
When using the INCX-4101 simply connect the power connector
from a matching PS-1230US-XLR into the appropriate
connector on the outside of the INCX-4101.
Note that a Liteway PS-1205 will not provide enough power for
this application. A PS-1230US 3 Amp supply is required to
power the INCX-4001 intercom stations and speaker while a PS-
1230-USXLR is required to power the INCX-4101 and ACC-
1004-XLR intercom station for proper operation..
IN EITHER CASE DO NOT APPLY MORE THAN 16 VOLTS DC OR
DAMAGE TO THE UNIT MAY OCCUR.!
4. Audio will now come through the external speaker instead of the
intercom station’s built in speaker. The audio output volume is
controlled by the front panel volume control of the INCX-4001 or
INCX-4101 intercom station.
Connections for powering the ACC-1004 and INCX-4001
For further information consult the instruction manual for either
the INCX-4001 or INCX-4101 as required.
Este manual sirve para los siguientes modelos
1
Otros manuales de Oradores de Litelink
