Lionelo NOA Manual de usuario
NOA
User manual
The baby seat is suitable for children older than 15 months.
The baby seat is suitable for children weighing from 0 to 13 kg
WARNING: DO NOT MOUNT the baby seat on front car seats
with active airbags.
This baby seat can only be installed in a rear-facing position.
Baby seat:
Shoulder straps height adjustment
Shoulder
Buckle
Cover
Handle
Handle
Back
Adjustment strap
Belt guide
Strap holes
Lap strap
The shoulder straps should be placed as close to the
baby’s shoulders as possible. If the position of the
straps is incorrect, remove them and install at a
suitable height.
Straps usage / adjustment:
If the position of the safety straps is not suitable for
your child, please complete the following steps:
Step 1: loosen the shoulder straps.
Step 2: remove both straps from the baby seat and
uncouple them.
Step 3: run the straps through the proper holes.
Make sure that both straps are installed at the same
height and they are not twisted.
Too low
Too high
Correct
1. Loosening the straps:
Step 1: Press the button located under the seat, at
the front of the baby seat.
Step 2: While holding the button, pull the shoulder
straps to loosen them.
2. Securing a child in the baby seat:
When the shoulder straps are properly adjusted to
the height of your child, please complete the
following steps:
Step 1: Unfasten the buckle and put the straps apart
so that they don’t block the seat. Then, place your
child in the baby seat.
Step 2: Run the shoulder straps over the baby’s
shoulders and put the two metal connectors
together, as shown in the picture 1.
Step 3: Insert the joint connector into the buckle, as
shown in the picture 2. The “click” sound indicates
that the connector has been properly locked in the
buckle.
Step 4: Pull the shoulder straps to make sure that
they are properly secured in the buckle, as shown in
the picture 3.
3. Tightening the straps:
Pull the shoulder straps up so as to stretch them out.
Then pull the adjustment strap to tighten the
harness.
The shoulder straps should be neither too tight nor
too loose so as not to cause discomfort to the child.
Securing the baby seat:
In order to properly mount the baby seat in a car,
please refer to the corresponding information in the
vehicle’s manual.
Do not mount the baby seat in a vehicle’s front car
seat with active airbags.
This baby seat can only be secured in a car with a 3-
point seat belt.
The baby seat must be installed in a rear-facing
position.
Step 1:
Move the lever to the extended
position. Place the baby seat on
the car seat. The handle must
be rested on the back of the car
seat.
Step 2: Run the belt through all
guides of the baby seat. Lock
the belt connector in the
vehicle’s safety buckle. Pull the
belt to make sure it is properly
secured in the buckle.
Step 3: Hook the shoulder part
of the belt in the guide located
at the rear side of the baby
seat’s back.
Step 4: Tighten the 3-point seat
belt by pulling it as it is shown
in the picture.
After all these steps the baby
seat is properly installed and
secured.
Make sure that the belt hasn’t twisted during the
installation and it is properly tightened.
To remove the baby seat from the car, please follow
the above steps in reverse order.
Changing the handle’s position:
The seat’s handle can be placed in 4 different
positions. In order to change the position, press the
red buttons at the both sides of the baby seat
simultaneously. The buttons are located in the side
corners of the baby seat.
You can place the handle in 4 different positions:
1. It is the only position you can use while mounting
the baby seat on a vehicle’s seat.
2. Basic position - you can choose it to carry a child.
3. Resting position - use it to freely put a child in/out
of the baby seat.
4. Base position - ideal when you feed or play with a
child.
Each time you change the handle’s position make
sure it has been properly secured (locked).
Using the hood:
The handles at the ends of the frame are adjustable.
“Click” sounds indicate that the hood has been
properly folded / unfolded.
Maintenance:
The cover can be easily removed for cleaning. In
order to do so, first pull the straps out of the baby
seat. Then remove the cover.
Cleaning: Straps and plastic parts can be cleaned
with mild detergents and warm water (up to 30o). Do
not clean the baby seat or any of its components
with chemicals, bleachers or corrosive liquids.
Tabla de contenidos
Idiomas:
Otros manuales de Asiento de coche de Lionelo
Lionelo
Lionelo Bastiaan Manual de usuario
Lionelo
Lionelo Braam i-Size Manual de usuario
Lionelo
Lionelo jasper Manual de usuario
Lionelo
Lionelo Bastiaan Manual de usuario
Lionelo
Lionelo Aart Manual de usuario
Lionelo
Lionelo LEVI PLUS Manual de usuario
Lionelo
Lionelo Bastiaan Manual de usuario
Lionelo
Lionelo Neal Manual de usuario
Lionelo
Lionelo sander Manual de usuario
Lionelo
Lionelo SEM Manual de usuario
Lionelo
Lionelo Levi One Manual de usuario
Lionelo
Lionelo Bastiaan RWF i-Size Manual de usuario
Lionelo
Lionelo Liam Manual de usuario
Lionelo
Lionelo sander Manual de usuario
Lionelo
Lionelo Astrid i-Size Manual de usuario
Lionelo
Lionelo Lars i-Size Manual de usuario
Lionelo
Lionelo Liam Manual de usuario
Lionelo
Lionelo NOA PLUS Manual de usuario
Lionelo
Lionelo Lavender i-Size Manual de usuario
Lionelo
Lionelo Oliver Manual de usuario
