Lionel Plug-Expand-Play Classic Automatic Gateman Manual de usuario

78-1063-250

7/18

Lionel

Plug-Expand-Play®

Classic Automatic Gateman

Owner’s Manual

Lionel

Plug-Expand-Play®

Classic Automatic Gateman

Owner’s Manual

Thank You!

Automatic Gateman basics

Assembling your Gateman (6-81063 Gateman Only) 2

Replacing the LED 2

Connecting your Gateman using Plug-Expand-Play 3-5

Wiring options

Connecting your Gateman using FasTrack 6

Connecting your Gateman using a FasTrack Accessory Activation Pack 6-12029 7

Connecting your Gateman using Tubular Track 8

Connecting your Gateman using a Transformer 9

Wiring for TMCC or LEGACY

SC-2 wiring and operation 10

ASC wiring and operation 11

Lionel Limited Warranty Policy & Service 12

Thank you for your purchase of this Plug-Expand-Play Automatic Gateman accessory! The Lionel

automatic gateman has been warning of approaching trains since 1935. As a speeding train

nears, the shanty door opens, and the vigilant gatemen rushes out, swinging his red lantern.

After the train passes, the gateman returns to his shed. Locate this accessory wherever

pedestrians or cars cross the tracks on your railroad.

The following Lionel marks are used throughout this Owner’s Manual and are protected under law. All

rights reserved.

Lionel®, FasTrack®, LEGACY®, LEGACY®Control System, Lockon®, TMCC®, CAB-1®Remote Controller,

Plug-Expand-Play®, ASC®, Accessory Switch Controller®

Table of Contents

CROSSING

RAIL ROAD

Assembling your Gateman (6-81063 Gateman Only)

Assemble your crossing sign to the base with the two screws provided.

Note that you may orient the sign in either direction. Using a

Phillips screwdriver, insert each screw into the holes on the crossing sign.

Tighten the screws so that the sign is securely attached to the base.

Figure 1. Attaching the

crossing sign

Replacing the LED

Your Automatic Gateman is illuminated an LED that is expected to last for the life of the accessory.

The LED is not user serviceable. If service is required, we recommend that you have your acces-

sory serviced at a Lionel Factory Trained Authorized Service Station or Lionel Service.

Connecting your Gateman using Plug-Expand-Play

Lock-on

Power Supply

(optional)

Power Block

Lock-on

Remote

Control Box 3-pin male

connector

3-pin male

connector

Automatic

Gateman

Your automatic gateman comes with a remote control box. This allows you to turn the interior

lamp ON or OFF and activate the animation in either the ON or OFF positions by pressing the

control button down. Connect your gateman to the remote control box by plugging in the 3-pin male

connector into the 3-pin female slot on the back of the remote control box. Next, plug in the 3-pin

male connector on the remote control box into either a Plug-Expand-Play lock-on (6-81313) or a

Plug-Expand-Play power block lock-on (6-81314). See ﬁgure 2 for wiring.

Follow these instructions to illuminate your gateman accessory and activate ﬁgure movement.

• Slide the knob forward to turn on the lamp in the building.

• With the knob in the forward position, push down to make the gateman appear. Notice that

the building will stay illuminated.

• Slide the knob back to the "OFF" position to turn off the lamp in the building.

Figure 2. Connecting your accessory to a lock-on

Note If you plug in your automatic gateman directly

into either the lock-on or power block lock-on, it

will be constantly illuminated. The gateman will

not appear from the inside of the building.

Automatic Gateman basics

Connecting your Gateman using Plug-Expand-Play continued

Your Automatic Gateman requires the use of a Plug-Expand-Play Activator Track Pack (6-81317)

in order for the animation to take place.

When your Automatic Gateman is connected to the lock-on section of the track pack, power will

be constantly supplied (the light in the building will be on constantly). Once your train passes into

the insulated section of track (crossing the break in the 5" piece of track), the gateman will appear

from the door (the light will remain ON). Once the train leaves the insulated section (crossing the

next break in the other 5" piece of track), the gateman will return to the inside of the building (the

light will remain ON). See figure 3 on page 5.

Do NOT forcefully connect your accessory's 3-pin male connector into the 3-pin female

connector on the lock-on. Doing so will damage the pins on the accessory and/or the

lock-on. Make sure that you are also inserting the connectors with the proper orienta-

tion. Lionel's Limited Warranty does NOT cover this type of damage to your products.

Note!

Please be aware that adding additional accessories will take power away from the track,

thus resulting in less available power for running trains. If your power supply shorts out

(turns off) when using this accessory it is most likely caused by overdrawing the available

power the transformer can provide. Should this occur you will be required to increase the

size of the transformer powering the track. Go to www.lionelstore.com for power supply

options.

Note!

In order for your Automatic Gateman accessory to operate automatically, you will need

either of the following:

• Plug-Expand-Play Activator Track Pack (6-81317)

• Plug-Expand-Play Lock-on (6-81313 or 6-81314)

• FasTrack Accessory Activator Pack (6-12029)

Using the Plug-Expand-Play Activator Track

Automatic Gateman basics

Connecting your Gateman using Plug-Expand-Play continued

Automatic Gateman

Accessory

Automatic Gateman

Accessory

Automatic Gateman

Accessory

3-pin male connector

Lock-on

5"track

with break

5"track

with break

10"track

FasTrack

Train

FasTrack

As the Automatic Gateman is connected to the

lock-on, power is supplied through the track to the

accessory and the light is ON.

As the train passes over the 5" track section, the

door opens and the gateman comes out of the

building to greet the train as it passes by. The light

remains ON.

As the train leaves the other 5" track section, the

gateman returns to his post in the building and the

door closes. The light remains ON.

Figure 3. Connecting the Gateman to the lock-on

Automatic Gateman basics

Connecting your Gateman using FasTrack

Wiring options

You also are able to connect your automatic gateman to FasTrack using the 8" 3-pin female pig-

tail (6-82038 - SOLD SEPARATELY). Plug in the 3-pin male connector from the accessory into

the 3-pin female slot on the back of the remote control box. Next plug in the 3-pin male connector

from the box into the 3-pin female pigtail. Then attach the red wire to the inside rail and the black

wire to the outside rail. See figure 4.

Follow these instructions to illuminate your gateman accessory and make the gateman appear

from the building.

Note The white wire is not used when connecting your automatic gateman to FasTrack.

• Slide the knob forward to turn on the lamp in the building.

• With the knob in the forward position, push down to make the gateman appear. Notice that

the building will stay illuminated.

• Slide the knob back to the "OFF" position to turn off the lamp in the building.

Automatic

Gateman

Remote control box

3-pin male connector

3-pin female connnector

FasTrack

Underside of FasTrack

Red wire

Black

wire

8" 3-pin female pigtail

(sold separately)

Figure 4. Connecting your gateman to FasTrack

Wiring options

Wiring and operating your accessory using FasTrack Accessory

Activator Pack

See ﬁgure 5 below for wiring your accessory using the FasTrack Accessory Activator Pack (6-12029

SOLD SEPARATELY) and the 8” 3-pin female pigtal (6-82038 SOLD SEPARATELY). Power is

supplied through the track to the accessory and the light will stay illuminated.

Underside of 10 inch FasTrack piece

Red wire

White wire

Black

wire

Automatic

Gateman 3-pin male connector

8" 3-pin female pigtail

(sold separately)

3-pin female connnector

Figure 5. Connecting your gateman to the FasTrack Accessory Activator Pack

5"track

with break

5"track

with break

10"track

Wiring options

Connecting your Gateman to Tubular Track

You can also connect your automatic gateman to tubular track using the remote control box and

the 8" 3-pin female pigtail (6-82038 - SOLD SEPARATELY). Plug in the 3-pin male connector of

the gateman into the 3-pin female slot on the back of the remote control box. Next plug in the 3-pin

male connector from the box into the 3-pin female pigtail. Then attach the red wire to the inside rail

position of the universal lock-on (6-24213) and the black wire to the outside rail position. See figure

Follow these instructions to illuminate your gateman accessory and make the gateman appear

from the building.

Note The white wire is not used when connecting your automatic gateman to tubular

track.

• Slide the knob forward to turn on the lamp in the building.

• With the knob in the forward position, push down to make the gateman appear. Notice that

the building will stay illuminated.

• Slide the knob back to the "OFF" position to turn off the lamp in the building.

Automatic

Gateman

Remote

Control Box

Tubular track

Universal lock-on

Red wire

Black wire

3-pin male connector

3-pin female connector

8" 3-pin female pigtail

(sold separately)

Figure 6. Connecting your gateman to tubular track.

Connecting your Gateman to a Transformer

To power your automatic gateman with a CW-80 Transformer (6-14198), you will need the 8"

3-pin female pigtail (6-82038 - SOLD SEPARATELY) and the included remote control box to

connect to the transformer terminals. Make sure that all connections are secure. Loose connections

can produce extremely high temperatures. For this reason, do not touch the terminals or track

connections during use. Also, do not locate scenery materials such as lichen or ground foam near

the terminals.

1. Plug in the 3-pin male connector on the gateman to the 3-pin female slot on

the remote control box.

2. Plug in the 3-pin male connector on the remote control box to the 3-pin

female slot on the pigtail.

3. Loosen the red TRACK thumbscrew terminal, then place the red wire on the

metal terminal bar. Still holding the wire end, tighten the red thumbscrew

until secure. Be sure that the wire is touching the metal post.

4. Loosen the black TRACK thumbscrew terminal, then place the black wire

on the metal terminal bar. Still holding the wire end, tighten the black

thumbscrew until secure. Be sure that the wire is touching the metal post.

5. Plug the CW-80 Transformer into your wall outlet (120 volts).

6. Apply 12-14 volts of power by raising the orange throttle on the transformer.

Follow these instructions to illuminate your control tower and activate figure movement.

• Slide the knob forward to turn on the lamp in the building.

• With the knob in the forward position, push down to make the gateman appear. Notice that

the building will stay illuminated.

• Slide the knob back to the "OFF" position to turn off the lamp in the building.

120/60z

0~18VAC

TRACK ACCESSORY

Automatic

Gateman

Remote

Control Box

3-pin male

connector

3-pin male

connector

3-pin female

connector

Transformer

Black wire

Red wire

8" 3-pin female

pigtail

(sold separately)

Figure 7. Connecting your gateman to a transformer.

Wiring options

Wiring for TMCC or LEGACY

To power your automatic gateman in the Command Control and LEGACY environments, you will

need an SC-2 (6-22980), an ASC (6-14182), or an ASC2 (6-81639). You will also need the 8"

3-pin female pigtail (6-82038 - SOLD SEPARATELY) and a transformer (6-14198). See ﬁgures 8 and

9 for wiring.

Note Refer to your CAB-1, CAB-1L, or LEGACY manual for remote instructions.

SC-2 wiring and operation

Four wires are needed to connect your accessory to the SC-2 and a separate accessory transformer.

Refer to Figure 8.

1. Attach a wire to the transformer Common/Ground/U terminal and connect it to the COMM (com-

mon) position on the SC-2.

2. Connect the white wire of the pigtail to the AUX1 terminal on the SC-2.

2. Connect the black wire of the pigtail to the AUX2 terminal on the SC-2.

3. Finally, connect the red wire of the pigtail to the transformer Power/A terminal.

AUX2 will turn the lamp in the building ON. Pressing AUX2 again will turn the lamp OFF. Pressing

AUX1 will make the gateman appear from the building. The gateman will return to the inside of the

building when AUX1 is released.

ACC3 ACC4

ACC1 ACC2

Automatic Gateman

SC-2 White wire

Red wire

Black wire

Transfomer

3-pin male

connector

3-pin female

connector

8" 3-pin female

pigtail

(sold separately)

Figure 8. Wiring an SC-2.

Tabla de contenidos

Otros manuales de Juguete de Lionel

Lionel

Lionel O-27 Santa Fe FT Passenger set Manual de usuario

Lionel

Lionel 2289WS Berkshire Freight Set Manual de usuario

Lionel

Lionel Summer Vacation Manual de usuario

Lionel

Lionel Alco PB-1 Manual de usuario

Lionel

Lionel 390E Manual de usuario

Lionel

Lionel MTH Helicopter Car Mini Commander Manual de usuario

Lionel

Lionel Conventional 2-6-0 Mogul Steam Locomotive Manual de usuario

Lionel

Lionel FlyerChief Berkshire Locomotive and Tender Manual de usuario

Lionel

Lionel Hudson Manual de usuario

Lionel

Lionel Alco PA-1 Manual de usuario

Lionel

Lionel 71-8340-250 Manual de usuario

Lionel

Lionel Truss Bridge with Flasher and Piers Manual de usuario

Lionel

Lionel HOBO EXPRESS Manual de usuario

Lionel

Lionel Thomas & Friends Manual de usuario

Lionel

Lionel VISION Line700E Hudson Manual de usuario

Lionel

Lionel Drawbridge Manual de usuario

Lionel

Lionel Holiday Special Train Set Manual de usuario

Lionel

Lionel Rio Grande General Manual de usuario

Lionel

Lionel 73-1747-250 Manual de usuario

Lionel

Lionel F3 A-A DIESEL LOCOMOTIVE SET Manual de lista de piezas

Lionel

Lionel 4-6-2 Pacific Manual de usuario

Lionel

Lionel VISION ATSF 3000 2-10-10-2 Manual de usuario

Lionel

Lionel FT Passenger LionChief Manual de usuario

Lionel

Lionel LCCA Reading Mining Set Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario