Lionel LionChief Plus 2.0 GP20 Manual de usuario

Lionel

LionChief Plus 2.0 GP20

Diesel Locomotive

Owner’s Manual

Lionel

LionChief Plus 2.0 GP20

Diesel Locomotive

Owner’s Manual

20234140250

5/22

Thank You!

Thank you for your purchase of this Lionel diesel locomotive! On the outside, this locomotive

features numerous details and expert decoration in your favorite livery. This locomotive is

equipped with some of the most advanced sounds and controls in model railroading. This powerful

locomotive is ready for duty on your layout.

This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt

RSS standard(s). Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Contains

P/N: BM832(A)

FCC ID: X8WBM832

IC ID: 4100A-BM832

FCC Statement

LionChief® Plus 2.0

A step-up from our traditional set locomotives, these locomotives include improved

sounds, additional light and smoke features, speed control and the ability to be run via

conventional transformer or TMCC Command Control in addition to Bluetooth.

ODYSSEY II® Speed Control

Slow speed and start-up operation are smooth and steady with ODYSSEY II®Speed

Control. Watch your locomotive as it creeps through the yard or ghts up a grade

without hesitation.

LionChief® Bluetooth®

Incorporating Bluetooth technology into Lionel model trains opens a new world,

integrating the tradition of model railroading with the latest smart-device technol-

ogy. With Lionel’s new LionChief app, you can control full operation and sounds

directly from your Bluetooth-enabled smart phone or tablet and operate multiple

locomotives from the same device. LionChief is available to smartphone users and

is compatible with all 2017 to current LionChief, LionChief Plus, S-Gauge, and HO

Trains.

Lionel Voice Control

Simply speak a command into your phone via your LionChief app and watch as your

engine follows your lead! e Lionel Voice Control feature is available on all new and

previously produced Bluetooth equipped engines.

Table of Contents

Running your locomotive

Powering your locomotive 4

LEGACY controller operations 4-5

TrainMaster Command Control (TMCC/Command Control) operations 6

Conventional transformer operations 7

Locomotive basics

Adding smoke fluid to your locomotive's smoke generator 8

Locomotive switch locations 8

Assigning your locomotive a new ID# (LEGACY and TMCC) 9

LEGACY controller operations

The LEGACY CAB-2 Remote Controller 10

The Velocity Throttle 11

The Multi-Controller 11

The Train Brake Slider 11

The Warning Sound Controller 12

The Speed Bar 12

RailSounds Sound System operations

RailSounds sound system 13

Using the Bluetooth LionChief App

Connecting your Bluetooth-equipped locomotive on Apple devices 14

What if my Bluetooth enabled engine didn’t automatically connect? 15

Connecting your Bluetooth-equipped locomotive on Android devices 16

Running Your Locomotive 17

Settings 18

Volume Control 18

Switching Connection Between Multiple Bluetooth®Locomotives 19

Lionel Voice Control 20-21

Troubleshooting 22

Using the LionChief Universal Remote

The LionChief Universal Remote (6-83071) 23-24

Adjusting the locomotive volume using the Universal Remote 25

Pairing locomotives to the Universal Remote 25

Operating locomotives with the Universal Remote 26-27

TrainMaster Command Control operations

CAB-1 Remote Controller commands 28

CAB-1 Remote Controller numeric keypad commands 29-30

Setting the smoke level 30

Customizable Horn and Bell Feature 30

Conventional transformer operations

Using the RailSounds sound system in the conventional environment 31

Activating CrewTalk dialog 31

Locking your locomotive into a single direction 32

Reprogramming your locomotive to restore features 32

Maintaining and servicing your locomotive

Lubricating your locomotive 33-34

Servicing your locomotive’s LEDs 34

Replacing the traction tires 35

Locomotive diagnostics 35

Lionel Limited Warranty Policy & Service 36

Your LionChief Plus 2.0 locomotive requires Lionel or Lionel-compatible O-31 or larger

track curves.

1. Turn off track power, and then plug in the LEGACY Base and connect it to the track.

2. Place your locomotive on the track.

3. Increase track power voltage to full power (no more than 19 volts AC). If a circuit

breaker trips when you turn on the Lionel power supply, check the wheels of your locomotive to

make sure they are all securely on the track. Check to make sure the track is free of all metals that

may cause a short circuit.

4. As illustrated in Figure 1, press ENG and 1 (or your selected ENG ID#) to address the

locomotive with your LEGACY CAB-2 Remote Controller.

Note!

Running your locomotive

Figure 1. LEGACY engine selection

LEGACY controller operations

Your LionChief Plus 2.0 locomotive is compatible for operation with the Lionel LEGACY system.

It will also operate on the original Lionel TrainMaster System (TMCC1) and also on the LEGACY

Cab-1L / Base-1L operating system.

Your commands are sent by the Remote Controller to the Command Base, which broadcasts

a radio frequency that is distributed through the outer rails of the track to your locomotives.

Your locomotive will not respond until it recognizes its unique ID#, so you can operate multiple

Command-equipped locomotives on the same track at the same time.

Powering your locomotive

Your locomotive is designed to work with either AC or DC power.

AC Power: Use an alternating-current (50-60Hz AC) transformer for Legacy, Bluetooth, or

Conventional control. Powering your locomotive in excess of 19 volts AC may result in damage to

sensitive electronic components.

DC Power: Use a DC transformer for Bluetooth control only. You locomotive is not designed to

operate with Legacy or conventional control while using DC power. Powering your locomotive in

excess of 19 volts DC may result in damage to sensitive electronic components.

5. After selecting the ENG ID# on the Cab 2 remote, your remote needs to be configured

for TMCC or CAB1 control for the locomotive. Select the engine ID# of your LC+ 2.0

engine as before, then press the INFO button on the top right of your CAB-2 remote.

Press the SCROLL button on the top left of the CAB-2 row until the CONTROL tab is selected.

Press the button that corresponds to the TMCC or CAB1 Mode selection on the screen.

Congratulations! You have now configured your CAB-2 remote to run your LC+ 2.0 locomotive in

TMCC mode. Enjoy all the features your locomotive has to offer.

6. Press the Start Up key on your LEGACY CAB-2 Remote, shown in Figure 4. Then,

throttle up and move 'em out! Your engine sound will start up, and the locomotive-specific

touch screen buttons will populate the remote. For more information on operating your

locomotive with the LEGACY system, please refer to the LEGACY section of this manual.

Additional information is also found in the LEGACY System Manual, available online at www.

lionel.com.

Running your locomotive

LEGACY controller operations continued

Figure 4. LEGACY start-up

Figure 2. CAB-2 info button

Figure 3a. CAB-2 scroll button Figure 3b. CAB-2 control screen

ENGINE 1 INFO

Custom

Type

OTH TMCC

CAB1 TMCC LE

LIONEL TMCC

LRS

Control

Sound

TrainMaster Command Control (TMCC/Command Control) operations

For operation in the TrainMaster Command Control environment, you need a TrainMaster

Command Base (6-12911) and a CAB-1 Remote Controller (6-12868). Refer to your TMCC

System Manual for complete information.

Your commands are sent by the CAB-1 Remote Controller to the Command Base, which

translates the command into digital code. That code is sent through the outside rails to your

locomotive, which will not respond until it recognizes its unique ID#. TrainMaster Command

Control gives you the power to operate multiple Command-equipped locomotives on the same track

at the same time.

1. Turn off track power, and then plug in the Command Base and connect it to the

track.

2. Place your locomotive on the track.

3. Increase track voltage to full power (no more than 19 volts AC). If a circuit breaker

trips when you turn on the Lionel power supply, check the wheels of your locomotive to make

sure they are all securely on the track. Check to make sure the track is free of all metals that may

cause a short circuit.

4. Press ENG and 1 to address your locomotive with your CAB-1 Remote Controller.

5. Throttle up and move ‘em out.

For more information, please refer to the TrainMaster Command Control operations section of

this manual or the TMCC System Manual, available online at www.lionel.com.

Note! Your LionChief Plus 2.0 locomotive requires Lionel or Lionel-compatible O-31 or larger

track curves.

Running your locomotive

Conventional transformer operations

For Conventional operation, a Command Base must not be powered up

anywhere in the area, even if it is not connected to the track. If a base is detected, your

locomotive will default to Command mode.

Your LionChief Plus 2.0 locomotive requires Lionel or Lionel-compatible O-31 or

larger track curves.

To access ALL of the features of your LionChief Plus 2.0 locomotive you must operate in

the TMCC environment as described on page 6.

1. With track power off, place your locomotive on the track.

2. Power up the track. If a circuit breaker trips when you turn on the Lionel power supply, check

the wheels of your locomotive to make sure they are all securely on the track. Check to make

sure the track is free of all metals that may cause a short circuit.

3. Move ‘em out! When the locomotive's headlight illuminates and the LEGACY RailSounds

sound system starts, press the DIRECTION button on your transformer to sequence your

locomotive through the repeating pattern of operations: neutral, forward, neutral, reverse,

neutral, and so on. You may also briefly turn off track power to advance the locomotive to the

next operating state. Adjust the throttle until your locomotive moves at your desired speed.

When placing your locomotive on your layout for the first time and after power interruptions

lasting longer than five seconds, it will start out in neutral.

Use the Whistle and BELL buttons on your transformer to activate those features. For

more information, please refer to the Conventional transformer operations section of

this manual.

If your locomotive is running in Conventional mode, it can be interrupted by a Bluetooth

Control device. If you do not wish for this to happen, locate the Bluetooth ON/OFF switch

and move it to the OFF position. Refer to Figure 6 on page 8.

Note!

Adding fluid to your locomotive’s smoke generator

Note!

Your LionChief Plus 2.0 locomotive is equipped with a smoke generator that produces safe,

clean, white smoke during operation. The smoke generator for this locomotive supplies

the stack smoke effect. The reservoir contains the fluid and wick which, once saturated, sup-

plies the heating element with the right amount of fluid.

For best performance, we recommend using only 6-37841 Lionel Premium Smoke

Fluid.

Exhaust Smoke

Loading smoke fluid into either of the exhaust stacks will

provide smoke fluid for the exhaust smoke effect. When adding

fluid DO NOT EXCEED 20 DROPS as this can cause your

smoke unit to become oversaturated allowing leakage onto the

electronics. Note that operating your locomotive's smoke unit

without smoke fluid will cause damage to the heating element.

Add 20 drops initially and 10 to 20 thereafter, as required to

maintain desired smoke.

Your locomotive's smoke fluid consumption will vary

depending on the smoke level setting you have selected.

Note! Figure 5. Exhaust smoke location

Locomotive basics

Refer to Figure 5 as you add the smoke fluid. If you prefer to operate your locomotive without

smoke, locate the smoke unit switch under under the cab of the locomotive and slide it to the OFF

position. Refer below for the location of the switch.

The functions of your LionChief Plus 2.0 locomotive's switches are outlined below. The instruc-

tions below are specific to this particular locomotive; note that available features

(and switches) may differ from other locomotives and sets.

Locomotive switch locations

Smoke Switch

Used to turn the smoke unit on

and off.

Program / Run Switch

Used to assign an ID# and

reprogram the locomotive in

Command operation when the

switch is in the PROG position.

Also used to “lock” your locomotive

in a single direction, or neutral,

in conventional operation when

the switch is placed in the PROG

position.

Bluetooth Switch

Used to turn the Bluetooth

module on and off.

Adding fluid to your locomotive’s smoke generator continued

Figure 6. Switch locations

Bluetooth

switch

Smoke

switch

Add smoke to

either stack

Program/Run

switch

For operation in the Command Control environment, you will want to give your LionChief Plus

2.0 locomotive a unique ID#. Your locomotive will respond to commands associated with its

ID# while all other units will disregard these commands. This procedure is not necessary for

conventional (non-Command) or BlueTooth operation.

1. Slide the program run switch on your locomotive to the PROG position. See Figure 6

on page 8.

2. Place the locomotive on the track.

3. Connect the Command Base and plug it in.

4. Power up the track.

5. Press ENG on the CAB-1 or CAB-2 remote.

6. Enter the unique ID#. Choose any number from 1 to 98 that has not been assigned

to another locomotive (ENG). We recommend using a part of your locomotive’s road

number.

All Command Control enabled locomotives respond to ENG 99. We recommend that you

reserve ID# 99 as a "universal" ID#.

7. Press SET. The locomotive’s horn will sound, or the headlights will flash if the

RailSounds sound system is off.

8. Slide the program run switch back to the RUN position.

The LionChief Plus 2.0 locomotive ID# has been set. Be sure to record the new ID# for your

reference.

Locomotive basics

Assigning your locomotive a new ID#

Note!

LEGACY controller operations

The LEGACY CAB-2 Remote Controller

Main Display

Displays real-time information about your railroad

system. Displays real-time feedback of operation.

Scroll Button

Navigates through the entire list

of Engines, Trains, Switches, etc.

Select Button

Performs addressing by

3-4 digit road number.

Touch Screen Key Pad

A group of touch sensitive

keys with icons for each

function. These keys serve

many purposes and their icons

change accordingly.

Train Brake Slider

This slider is used to increase or

decrease the amount of Train Brake

affecting the engine or train.

Train Link Button

Quick select of Train-Link

devices (LEGACY Control

System Version 1.3)

AUX-2/Out Button

Controls switch direction.

Toggles all lights on/off,

except lights that are wired

to track power.

Emergency Halt Button

Stops everything on

layout; also stops

recording playback.

Record Button

Used to record and play

back events.

Velocity Throttle

Throttle control over

engines, also used to

navigate thru info/options.

Set Button

Used to set Engine address and for

programming.

Info Button

Used to enter/view the info/options of

selected components.

CTC Button

Press and hold to turn your remote

on and off. Tap this button to enter

the remote and base options. Tap it

again to return to the main screen.

Soft Keys

These keys directly correlate to the

5 selection boxes located at the

bottom of the main display. These

are also used in the info/option

menus to select options.

Warning Sound Controller

Warning Bell and Variable Whistle

control. Pull down to sound Whistle.

Push up and release to trigger

Warning Bell.

Official R.R. Speed Control Bar

Toggles the touchscreen display of R.R.

preset speeds and control panel.

Multi Controller

Boost, Brake, and Direction

control. Rock forward for Boost,

rock backward for engine brake,

and press down for direction

change. Click-hold-and rock for

absolute direction selection.

Front & Rear Coupler Buttons

Fire couplers.

Low, Medium, High Momentum Buttons

Used to select the desired momentum of

your addressed engine/train/accessory.

AUX-1/Thru Button

Press to view the Control

Panel while operating.

Controls switch direction.

Feedback Button

Toggle ON/OFF the vibration feedback

feature in the CAB-2 Remote.

Tabla de contenidos

Otros manuales de Juguete de Lionel

Lionel

Lionel O-27 Santa Fe FT Passenger set Manual de usuario

Lionel

Lionel Summer Vacation Manual de usuario

Lionel

Lionel Searchlight Car Manual de usuario

Lionel

Lionel Alco PA-1 Manual de usuario

Lionel

Lionel Empire State Express Hudson Manual de usuario

Lionel

Lionel Amtrak Acela Manual de usuario

Lionel

Lionel Illuminated Station Platform Manual de usuario

Lionel

Lionel G-Gauge Manual de usuario

Lionel

Lionel Non-Powered LEGACY RailSounds Super Bass F3... Manual de usuario

Lionel

Lionel Santa Fe Chief Manual de usuario

Lionel

Lionel Goofy & Pete Jumping Boxcar Manual de usuario

Lionel

Lionel GP-20 Manual de usuario

Lionel

Lionel 78-2055-250 Manual de usuario

Lionel

Lionel GP-7 diesel locomotive Manual de usuario

Lionel

Lionel 616 Flying Yankee Manual de usuario

Lionel

Lionel Veranda Manual de usuario

Lionel

Lionel New York Central Flyer Manual de usuario

Lionel

Lionel FlyerChief Berkshire Locomotive and Tender Manual de usuario

Lionel

Lionel 59 Minuteman Manual de usuario

Lionel

Lionel 73-1988-250 Manual de usuario

Lionel

Lionel 1-44 Manual de usuario

Lionel

Lionel Scrap Yard Manual de usuario

Lionel

Lionel SD-80 Diesel Locomotive Manual de usuario

Lionel

Lionel Pylon Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario