Lionel Halloween Witch Pylon Manual de usuario

Lionel

Halloween Witch Pylon

Owner’s Manual

Lionel

Halloween Witch Pylon

Owner’s Manual

71-4297-250

3/07

Congratulations on your purchase of the Lionel Halloween Witch Pylon! Watch as the witch

circles the tower.

Congratulations

• Pylon

• HalloweenWitch

• Supportarm

• Switch

• Threegreenwires

• Owner’sManual

Halloween Witch Pylon Inventory

Wiring your Pylon with a conventional power supply 3-4

Installing your Pylon 5

Attaching the witch to your Pylon 6

Operating your Pylon with a conventional power supply 6

Operating your Pylon with TrainMaster Command Control 7-8

Replacing the lamp in your Pylon 9-11

Limited Warranty/Lionel Service 12

Table of contents

The following Lionel marks may be used throughout this instruction manual and are protected under

Lionel®, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™, DynaChuff™,

StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1®Remote Controller,

PowerMaster®, Lionel ZW®, ZW®, PowerHouse®, TMCC®, Lionelville™, Lockon®, Wireless

Tether™, LionMaster®, FatBoy™, American Flyer®, TrainSounds™, PowerMax™

The name FasTrack®is used with permission from Pitsco, Inc.

Wiring your accessory is the first step in preparing for flight. The Pylon will operate best

at 12-18 volts (AC), and it can be powered through track power with a Lionel Lockon

(available separately, 6-62900), or a FasTrack Accessory Power Wire (available separately,

6-12053), OR through an accessory power supply. We recommend that you choose a power

supply that will allow you to increase or decrease the voltage to the accessory. Changing the

voltage allows you to control the speed at which the witch circles the pylon. Figure 1 on page 4

illustrates the following procedure.

To make proper connections, you need the insulation at the ends of the wires to be stripped

back 1/4” to 3/8”. To strip the wires, use a pair of wire strippers.

Only an adult should perform this task! Always use care when stripping wires.

1. Attach one wire to the #1 terminal of the track Lockon, a FasTrack Accessory Power Wire,

OR the Power/A terminal on the accessory power supply. Connect it to one of the terminals

on the separate switch (included with this accessory).

2. Attach an additional wire to the other terminal on the switch. Connect the other end of this

wire to one of the spring-clip terminals at the bottom of the pylon.

To make the spring-clip terminal connections, press down on the “springy” top of

the terminal clip so that a metal loop is formed. Slide the bare end of the wire into

the exposed loop. Release pressure on the terminal clip, allowing the crimped metal

to pinch the end of the wire in the metal loop. Give a little tug on the wire to check

if the hold is secure.

3. Attach another wire to the #2 terminal of the track Lockon, a FasTrack Accessory Power

Wire, OR the Common/Ground/U terminal on the accessory power supply. Connect it

directly to one of the spring-clip terminals at the bottom of the pylon.

At this point, your accessory is wired for power. See page 6 for how to operate this accessory

with a conventional (non-TrainMaster Command Control) power supply.

Wiring your Pylon with a conventional power supply

Caution!

Note!

Mounting

holes

Mounting

holes

Figure 1. Wiring for conventional operation

Wiring your Pylon with a conventional power supply

(continued)

FasTrack Accessory Power Wire

Choose a flat, level area on your layout for the accessory. Secure this accessory to your

layout with four screws (not included) using the holes near the corners of the base. Be

sure to wire your accessory before you secure it to your layout—the wire terminals are on the

underside of the base. Keep in mind that the witch flies in a circle with a diameter of 30”. The

flight path must be kept clear.

Installing your Pylon

Complete the assembly of your Pylon by attaching the witch and support rod to the

structure. Figure 2 illustrates the following procedure.

1. Note that the supporting rod has different shaped ends. Insert the D-shaped coupling

bottom end of the support rod onto the D-shaped mounting post on the top of the pylon.

Refer to the diagram for further assistance.

2. Insert the D-shaped top end of the rod into the D-shaped opening in the bottom of the

witch.

Attaching the witch to your Pylon

Figure 2. Installing the support rods

D-shaped coupling

support rod (bottom)

D-shaped

support rod (top)

D-shaped mounting

post on top of pylon

D-shaped

mounting hole,

bottom of witch

Adjust the voltage to the accessory to control the speed at which the witch circles the tower.

Increasing the voltage will cause the witch to circle faster; decreasing the voltage will

cause the witch to travel slower. To turn the accessory off, turn off the power supply or use the

switch attached to the wires in Step 1 on page 3.

Operating your Pylon with a conventional power supply

Pylon

Figure 3. Wiring for Command operation with an SC-2

Operating your Pylon with TrainMaster Command Control

You may choose to wire your accessory with an SC-2 Switch and Accessory Controller

(available separately, 6-22980) or the Accessory Switch Controller (available separately,

6-14182). Refer to these manuals for additional information.

SC-2 wiring and operation

Three wires (not included) are needed to connect your Pylon to the SC-2 and a separate

accessory transformer. We recommend using 22 gauge wire. Refer to Figure 3.

1. Attach one wire to the transformer Common/Ground/U terminal and connect it to the

accessory COMM (common) position on the SC-2.

2. Connect one of the Pylon terminals to the accessory ON/OFF toggle position on the SC-2.

3. Finally, connect the remaining Pylon terminal to the transformer Power/A terminal.

Use the AUX2 button on your CAB-1 Remote Controller to toggle the Pylon ON and OFF.

Operating your Pylon with TrainMaster Command Control (continued)

Accessory Switch Controller wiring and operation

Three wires (not included) are needed to connect your Pylon to the Accessory Switch

Controller (ASC) and a separate accessory transformer. Refer to Figure 4.

1. Attach one wire to the transformer Power/A terminal and connect it to the COMM terminal

on the ASC.

2. Connect one of the Pylon terminals to a numbered accessory terminal on the ASC.

3. Finally, connect the remaining Pylon terminal to the transformer Common/Ground/U

terminal.

Use the AUX2 button on your CAB-1 Remote Controller to toggle the Pylon ON and OFF.

Figure 4. ASC connections

Your Pylon is illuminated by one lamp. During the course of normal operations,

this lamp may require replacement. Follow these steps to replace the lamp with Lionel

part no. 671-4217-300.

1. Lift the support arm out of the tubes at the top of the pylon. Also, remove any screws

securing the base to your layout.

2. Remove the four base screws from the underside of the base with a small Phillips-head

screwdriver and lift away the roof and pylon tower. Refer to Figure 5 on page 10 for the

location of the screws.

3. Locate the lamp inside the building. Carefully unscrew the lamp from the socket. Refer to

the Figure 6 on page 11 for the lamp location.

4. Install the replacement lamp.

5. Reassemble the Pylon, following these steps in reverse order.

Replacing the lamp in your Pylon

Replacing the lamp on your Pylon (continued)

Roof

screws

(recessed)

Roof

screws

(recessed)

Mounting

holes

Mounting

holes

Base of the Pylon

Figure 5. Screw locations

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Juguete de Lionel

Lionel

Lionel GP-7 diesel locomotive Manual de usuario

Lionel

Lionel Hogwarts Express G Gauge Manual de usuario

Lionel

Lionel American Flyer Manual de usuario

Lionel

Lionel 6-19810 Manual de usuario

Lionel

Lionel Century Club II Manual de usuario

Lionel

Lionel American Flyer ALCo PB-1 Manual de usuario

Lionel

Lionel Percy Manual de usuario

Lionel

Lionel Non-Powered LEGACY RailSounds Super Bass F3... Manual de usuario

Lionel

Lionel Tie Car Manual de usuario

Lionel

Lionel 4-6-4 Dreyfuss Hudson Manual de usuario

Lionel

Lionel Caboose Manual de usuario

Lionel

Lionel 390E Manual de usuario

Lionel

Lionel Christmas Hudson Jr.Steam Locomotive Manual de usuario

Lionel

Lionel Smoking Boxcar Manual de usuario

Lionel

Lionel Cannon Car Manual de usuario

Lionel

Lionel Playtime Playground Manual de usuario

Lionel

Lionel Rio Grande General Manual de usuario

Lionel

Lionel Goofy & Pete Jumping Boxcar Manual de usuario

Lionel

Lionel Santa Fe Chief Manual de usuario

Lionel

Lionel ALCo S-2 Manual de usuario

Lionel

Lionel A Christmas Story Manual de usuario

Lionel

Lionel 73-1747-250 Manual de usuario

Lionel

Lionel Madison TrainSounds Baggage Car Manual de usuario

Lionel

Lionel U.S. ARMY SWITCHER 41 Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario