Lionel Command Control Gantry Crane Manual de usuario

78-2097-250

9/16

Lionel

Command Control

Gantry Crane

Owner’s Manual

Lionel

Command Control

Gantry Crane

Owner’s Manual

Congratulations!

Congratulations on your purchase of the Lionel Command Control Gantry Crane! The

Gantry Crane is compatible with Legacy Cab-2 or Cab-1L, or with TMCC Cab-1 remotes.

Add sounds synchronized to the actions of the Gantry Crane with the Crane Sounds Work

House (6-82035, sold separately).

Features of the Trackside Crane

• Command Control equipped

• 360-degree cab rotation

• Manual up and down operation of the boom

• Forward and backward trackside movement of entire crane unit

• Independent control of the hook

• Electromagnet control for moving metal objects

• Three powerful maintenance-free motors

Trainmaster Command Control

Products equipped with the classic TrainMaster Command Control system are controlled

by commands from your CAB-1 or CAB-2 Remote Controller. ElectroCouplers™, basic

sounds, and multiple unit lash-ups are all at your ﬁngertips as you walk around your

layout.

The following Lionel marks are used throughout this Owner’s Manual and are protected under

Lionel®, LionChief™, LionChief Plus™,TMCC®, LEGACY®, FasTrack®,TrainMaster®, Odyssey®,

RailSounds®, CrewTalk™, TowerCom™, DynaChuff™, StationSounds™, Pullmor®, ElectroCoupler™,

Magne-Traction®, CAB-1®Remote Controller, American Flyer®, Lionel ZW®, ZW®, MagniVision®,

TMCC®, Lionelville®, Wireless Tether™, Powerhouse™, LionMaster®, Conventional Classics™, Postwar

Celebration Series™, TruRail™, PH-1 Powerhouse®, Powermaster®, Powerstation-Powerhouse®,

Accessory Motor Controller™, AMC™, Accessory Switch Controller™, ASC™, Action Recorder

Controller™, ARC™, Track Power Controller 300™, TPC 300™, Track Power Controller 400™, TPC

400™, Block Power Controller™, BPC™, Operating Track Controller™, OTC™, FatBoy™, Lionel

Lines®, Joshua Lionel Cowen Series™, Lockon®, TrainSounds™, MultiHorn™, MultiWhistle™,

Choo-Choo™, SensorTrack™, Plug-Expand-Play™, Imagineering™, SensorCar™, LionScale™

Table of Contents

Gantry Crane basics

Preparing the Gantry Crane for operation 4

Powering your Gantry Crane 4

Assigning a new ID# to your Gantry Crane 5

Operating the Gantry Crane 6-7

Capabilities of the Gantry Crane 8

Operating the Gantry Crane

CAB-2 Remote Controller commands 9

CAB-1 and CAB-1L Remote Controller commands 10

Maintenance and Service

Storing the Gantry Crane 11

Lionel Limited Warranty Policy & Service 12

Preparing the Gantry Crane for operation

When you are ready to store your Gantry Crane, be sure to use the supplied elastic band to keep

tension on the hook line. Use your remote to position the boom to fit in the foam cavity.

Note Always keep light tension on the hook when handling the Gantry Crane.

Gantry Crane basics

Powering Your Gantry Crane

Your Gantry Crane is powered using track power. The Gantry Crane requires a special

track section for gantry unit motion available from other manufacturers (not included).

This track section has three rails in the middle for regular train operation, and two rails on

the outsides meant for Gantry Crane operation. Track positive connects to one of these rails,

and track negative to the other. The crane is reversible, so which rail is positive and which is

negative does not matter. See Figure 1 below for more information.

Power

(negative)

Boom down

Boom up

REAR OF CAB

Power

(positive)

Figure 1. 5 rail track power

Figure 2. Manually moving the boom up and down

Note Your Gantry Crane is factory programmed with an Engine ID# of “1.” To change

the ID#, see page 5.

As your fleet of LEGACY or TMCC equipped locomotives and equipment grows, you will want to

assign each unit a unique ID#. Use your CAB-1, CAB-1L, or CAB-2 Remote Controller.

1. Turn off power to the Gantry Crane.

2. Make sure that the Command Base is plugged in, then power up the crane.

3. Slide the RUN/PROGRAM switch to the PROGRAM position. Refer to Figure 3.

4. Press ENG or ACC.

5. Enter the ID# for the Gantry Crane using the numeric keypad on the Remote Controller.

Select any number between 1 and 98.

6. Press SET.

7. Slide the RUN/PROGRAM switch to the RUN position.

At this point, the new ID# has been set. When you power up, be sure to address the Gantry

Crane using the new ID#.

Assigning a new ID to your Gantry Crane

Figure 3. Switch location

When using the Legacy system the CAB-2 MUST be set to CAB-1 mode.

The crane will not respond to Legacy mode commands.

When using the CAB-1 or CAB-1L, the crane MUST be programmed as an

engine. The crane may be programmed as an accessory or an engine when

using a CAB-2.

Note!

Program/Run

switch

PRG

RUN

Gantry Crane basics

To operate the crane, you will need to use a Command Base and Remote Controller (LEGACY

CAB-2, CAB-1L, or CAB-1; all available separately).

Operating the Gantry Crane

Press ENG and 1 on the CAB-1, CAB-1L, or CAB-2 controller to select the Cab motor.

Rotate the THROTTLE knob clockwise on the CAB-1, CAB-1L, or

CAB-2 controller to rotate the cab clockwise.

Rotate the THROTTLE knob counter-clockwise on the CAB-1, CAB-

1L, or CAB-2 controller to rotate the cab counter-clockwise.

Cab-1 or Cab-1L remote LEGACY remote

The speed of the rotation of the boom is determined by

how fast the THROTTLE knob is rotated.

Note!

Operating the Cab Motor

Gantry Crane basics

Operating the Gantry Crane continued

Press 2 on the CAB-1, CAB-1L, or CAB-2 controller to select the Roll motor.

Rotate the THROTTLE knob clockwise on the CAB-1, CAB-1L, or

CAB-2 controller to make the Gantry Crane roll forward.

Rotate the THROTTLE knob counter-clockwise on the CAB-1, CAB-

1L, or CAB-2 controller to make the Gantry Crane roll backwards.

Cab-1 or Cab-1L remote

LEGACY remote

The speed that the crane rolls on the track is determined by how fast

the THROTTLE knob is rotated.

Pressing the DIR key on the CAB-1 or CAB-1L, or pressing down on

the BOOST/BRAKE button on the CAB-2 controller will reverse the

operation of the THROTTLE knob so that clockwise will move the

crane backwards and counter-clockwise will move the crane forward.

This allows the user to set it up so the control is intuitive based on

which side of the crane they are on. Setting is not retained when

power is turned off.

Note!

Operating the Roll Motor

Your Gantry Crane’s hook and electromagnet are capable of lifting approximately 4 oz (1/4

lb). The electromagnet automatically turns off after 60 seconds. The electromagnet cannot be

turned on again for 8 seconds.

Capabilities of the Gantry Crane

Gantry Crane basics

Press the BOOST key on the CAB-1, CAB-1L, or CAB-2 controller to raise the hook.

Operating the Hook Motor

Operating the Magnet

Press the BRAKE key on the CAB-1, CAB-1L, or CAB-2 controller to lower the hook.

Cab-1 or Cab-1L remote

LEGACY remote

The hook can be raised or lowered while the boom is being rotated or

while the crane is rolling.

Note!

Press the AUX2 key on the CAB-1, CAB-1L, or CAB-2 controller to toggle the Magnet

ON. If the magnet is left on it will turn off automatically after 60 seconds.

Press the AUX2 key again on the CAB-1, CAB-1L, or CAB-2 controller to toggle the

Magnet OFF. After the magnet is turned OFF it cannot be turned back on until it

has been off for 8 seconds.

Cab-1 or Cab-1L remote

LEGACY remote

The LEGACY CAB-2 Remote Controller

Rotates the cab and moves

the crane back and forth on

the gantry track.

Toggles the electromagnet

on and off.

Sets the throttle knob to

rotate the cab.

Sets the throttle knob to

control the roll motion of

the cab.

Raises and lowers hook.

Pressing DIR will switch

which direction the crane

moves on the gantry track

based on which direction

the throttle knob is rotated.

se your CAB-2 Remote Controller to operate your Gantry Crane.

Note

You can operate the hook while the cab is rotating or while the crane is moving.

We recommend that you keep a light weight on the hook for optimal performance.

The electromagnet will automatically turn off after 60 seconds. You must wait 8 seconds

before the electromagnet can be turned on again.

Do not allow the hook to go all the way down and then start to ascend again. If you

notice that the hook begins to ascend when it reaches its lowest point, press and hold

the BOOST button immediately to avoid reversing the controls.

Caution

Operating the Gantry Crane

CAB-1 & CAB-1L Remote Controller commands

Use your CAB-1 Remote Controller to operate the Gantry Crane.

Sets the throttle knob to rotate the cab.

Sets the throttle knob to control the roll

motion of the crane.

Lowers the hook on the crane.

Raises the hook on the crane.

Turns on the magnet.

Moves the crane back and forth along the gantry

track or rotates the cab.

Do not allow the hook to go all the way down and then

start to ascend again. If you notice that the hook begins to

ascend when it reaches its lowest point, press and hold the

BOOST button (up arrow) immediately to avoid reversing

the controls.

Caution

Note You can operate the hook while the

cab is rotating or while the crane

is moving.

Note

We recommend that you

keep a light weight on the

auxiliary hook for optimal

performance.

The electromagnet will automatically turn off after 60 seconds. You must wait 8

seconds before the electromagnet can be turned on again.

Operating the Gantry Crane

Tabla de contenidos

Otros manuales de Juguete de Lionel

Lionel

Lionel HO Veranda Manual de usuario

Lionel

Lionel O-27 Santa Fe FT Passenger set Manual de usuario

Lionel

Lionel SD-90 Manual de usuario

Lionel

Lionel Dash 9 Diesel Locomotive Manual de usuario

Lionel

Lionel Union Pacific RS-3 Manual de usuario

Lionel

Lionel 2-8-2 Mikado Manual de usuario

Lionel

Lionel Caboose Manual de usuario

Lionel

Lionel 4-8-2 Mohawk Manual de usuario

Lionel

Lionel Hogwarts Express Manual de usuario

Lionel

Lionel F9 Manual de usuario

Lionel

Lionel GP-38-2 Manual de usuario

Lionel

Lionel F3 Non-powered B Unit Diesel Locomotive Manual de usuario

Lionel

Lionel SD 60/70 Manual de usuario

Lionel

Lionel American Flyer 787 Log Loader Manual de usuario

Lionel

Lionel RS-11 Manual de usuario

Lionel

Lionel Hot Rod GP-9 Manual de usuario

Lionel

Lionel Union Pacific RS-3 Manual de usuario

Lionel

Lionel Arch Under Bridge 71-2770-250 Manual de usuario

Lionel

Lionel Playtime Playground Manual de usuario

Lionel

Lionel Pacific Manual de usuario

Lionel

Lionel Dash-9 Manual de usuario

Lionel

Lionel Fire Car Manual de usuario

Lionel

Lionel Hot Air Balloon Ride Manual de usuario

Lionel

Lionel Red Comet Tinplate Set Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario