Linn NEXUS Manual de usuario
LINN NEXUS
OWNERS MANUAL
2
NTRODUCTION Thank you for choosing our Linn NEXUS LS250 Loudspeakers, the result of
extensive design and development work. The NEXUS set new standards of performance in
loudspeakers of this type.
Remember, no loudspeaker is capable of improving the quality of the input signal so the NEXUS should
be used with good quality ancillary equipment.
INSTALLATION When removing the loudspeakers from their boxes, lift the cabinets out by their sides.
This will avoid damage to the grilles and the drive units.
Please retain all packing for possible future transportation.
All loudspeakers perform best when rigidly mounted. To achieve this, Linn have designed a KU-STONE
stand for the NEXUS, which includes floor spikes. Use of these KU-STONE stands will give optimum
sound quality and ensure that the drive units are in the correct position relative to the listener.
I
STANDS
3
Connection of the loudspeakers to the amplifier should be made with a good quality cable. Linn K20
loudspeaker cable is ideal, the leads should be terminated with the connectors supplied to ensure
optimum performance. The use of other connectors will degrade the sound quality of your system.
The cable is marked with the Linn symbol to indicate directionality. The bare wires shown should be
connected to the amplifier and the end marked with the circular logo should be connected to the
loudspeakers.
< LOUDSPEAKERS AMPLIFIER >
Take care to ensure that the wiring is correct. The red socket is positive and the black is negative. The
positive wire (red connectors is identified by a rib along the side of the cable.
NEXUS speakers are designed to perform best when placed close to a wall. Ideally the rear of the
loudspeaker should be between 4" and 12" (10cm and 30cm) from the wall and at least 18" (45cm) from
any corner. .
NEXUS can also benefit from being angled inward slightly by 5 to 10 degrees.
These are general guidelines and a little experimentation with positioning will optimise results for a
particular room, your dealer will be pleased to do this when he installs your equipment.
CONNECTIONS
POSITIONING
4
The NEXUS grille is special because it mounts directly onto the front baffle of the speaker. This avoids
the problems of diffraction produced by conventional grille frames.
The grille can be removed by gripping the top right corner, pulling it so that the elastic clears the baffle
and then carefully removing the rest.
Fitting the grille is a time consuming procedure, so unless you want to use the speaker without the grille,
it is best to leave it on. If you have to refit the grille, first find the join in the elastic and locate this in the
slot above the port before fitting the top part of the grille.
GRILLE
5
Bi-wiring improves the performance of a loudspeaker. By using a separate cable for the bass and treble
section some interaction between the bass and treble section is removed. The extra cost of an
additional pair of loudspeaker cables is more than justified by the improvement in sound quality gained.
To convert the NEXUS to bi-wired mode, use the key provided to unscrew the negative (black) socket
caps and remove the link. Replace and tighten the caps and then repeat for the positive (red) sockets,
and firmly re-tighten.
Because most amplifiers have only one speaker output you will have to double up the connection to the
speaker plug - your dealer will be pleased to make up the necessary leads for you, and to set up your
loudspeakers.
For ultimate performance you can go one step beyond bi-wiring and use two amplifiers, one channel for
the bass and one channel for the treble. Your dealer will be pleased to effect this mode of operation for
you.
BI-WIRING
BI-AMPING
6
Linn loudspeakers require no internal maintenance and on no account should you try to remove any of
the drive units, which are carefully tightened and sealed at the factory.
For servicing, always return the speakers as a pair to your supplier, using the original packing in order to
reduce the risk of damage in transit.
If you have lost the packaging, your supplier can provide a replacement set.
Ensure your equipment is insured by you during transit, repair, and return shipping.
These units are guaranteed under the conditions that apply in the country of purchase. To help us,
please return your guarantee card.
In addition to any statutory rights the customer may have, we undertake to replace any parts that have
failed due to faulty manufacture if you register your purchase with us.
Please keep a copy of your sales receipt as this will establish the purchase date of the loudspeakers
and refer all enquiries through authorised dealers only.
LINN PRODUCTS LIMITED, FLOORS ROAD, WATERFOOT, EAGIESHAM,
GLASGOW G76 OEP, SCOTLAND. TELEPHONE: ++44 (0)141 307 7777
FACSIMILE ++44 (0)141 644 4262
MAINTENANCE/SERVICE
GUARANTEE
Tabla de contenidos
Otros manuales de Oradores de Linn
Linn
Linn KOMPONENT 104 Manual de usuario
Linn
Linn MAJIK 126 Manual de usuario
Linn
Linn 5 Series Manual de usuario
Linn
Linn Sizmik 10.25 Manual de usuario
Linn
Linn SEKRIT Manual de usuario
Linn
Linn NINKA Manual de usuario
Linn
Linn Komri Manual de usuario
Linn
Linn KAN II Manual de usuario
Linn
Linn 328A Manual de usuario
Linn
Linn TUKAN Manual de usuario
Linn
Linn CUSTOM 2K 104C-S Manual de usuario
Linn
Linn SEKRIT Manual de usuario
Linn
Linn TRIKAN Manual de usuario
Linn
Linn Melodik Manual de usuario
Linn
Linn ESPEK Manual de usuario
Linn
Linn Komri Manual de usuario
Linn
Linn LOUDSPEAKERS Manual de usuario
Linn
Linn KABER LS500 Manual de usuario
Linn
Linn AV Loudspeaker Manual de usuario
Linn
Linn AV Personal Handset Manual de usuario
