Linksys PAP2 Manual de usuario

Linksys Sipura and PAP2 Analog Telephone

Adapter (ATA) - Installation Instructions

Below you will find installation instructions for the Linksys Sipura-200X or PAP2 broadband phone

adapter.

Setting up your Linksys ATA to work with KO TACT+ phone network is easy! The following

instructions will help you set up your adaptor in a simple Step-by-Step method.

Introduction How does broadband phone work?

Step 1 Connect ATA to your Broadband connection

Step 2 Verify & Configure your IP address

Step 3 Prepare you device to work with phone network

Step 4 Complete the Setup-Wizard

Step 5 Start using your ATA with KONTACT+ phone network

Introduction: How should the broadband adaptor connect to your

network?

You must have a broadband Internet connection and the Linksys ATA. Since the adaptor works

independently of your computer, there are no requirements at all for your operating systems.

In some case you will not necessarily need a router if your cable modem has 2 Ethernet ports and supports

NAT.

Routers and Broadband service are not sold through KONTACT+ phone network. Routers are generally

available from most retail or online stores.

Please follow the following step-by-step guide below to setup your Linksys ATA to work with

KO TACT+ phone network Broadband Phone Service.

Step 1: Connect the Linksys ATA to your Broadband connection

Use this illustration of the back of the ATA to connect it to your network.

1. Phone 1 - plug your analog telephone cord in here to work with your KONTACT+ phone network

account

2. Ethernet Port - use an Ethernet cable to connect your ATA to your router or Internet connection

3. Power connection - Connect the power to your ATA

Step 2: Verify & Configure your IP address

A. At first we would need to verify that your ATA would acquire an IP automatically if your

network supports DHCP.

If you have purchased your Linksys ATA adaptor from KO TACT+ phone network you should

skip this section and proceed to section B.

If your network utilizes a DHCP Server to assign IP Addresses to network devices, or if you are

connecting the ATA to a home router such as a Linksys or Netgear router, please do the following

1. Pick up the phone connected to Phone 1 of the ATA and enter "* * * *". You will hear a voice

prompt saying "Linksys configuration menu.".

2. Press the keys 1 0 1 # on your analog phone.

3. Then press 1 # to enable DHCP.

4. Then press 1 to save your configuration settings. Hang up the phone and wait for a couple of

minutes.

B. ext, we would need to verify that your ATA has a valid IP Address, Please be prepared with

pen and paper and proceed with the following:

1. Pick up the phone connected to Phone 1 of the ATA and enter "* * * *". You will hear a voice

prompt saying "Linksys configuration menu".

2. Press the keys 1 1 0 # on your analog phone. The system will now read back the IP address of

your ATA. Please write it down.

If the IP is 0.0.0.0, your ATA does not have a valid IP address. In this case you need to:

1. Hang up the phone, unplug and re-plug your ATA power cord.

2. Wait 2 minutes, and check the IP again.

3. If you still get 0.0.0.0, there can be three reasons for this

a. Your DHCP Server is not assigning an IP address to the ATA (in which case you should

contact your network administrator or ISP for assistance).

b. Your network does not have a DHCP server (in which case you should proceed to

configuring your IP manually using a Static IP configuration).

For instruction how to manually configure your static IP click here.

c. You have bought a Static IP (in which case you should proceed to configuring your IP

manually using a Static IP configuration).

For instruction how to manually configure your static IP click here.

Step 3: Prepare you device to work with phone network

If you have purchased your Linksys ATA adaptor from KO TACT+ phone network you should

skip this step and proceed to Step 4.

1. Open your configuration page. To do so, type the following into your web browser

http //aaa.bbb.ccc.ddd/admin/advanced where "aaa.bbb.ccc.ddd" represents the IP address of your

ATA.

2. Then, on your ATA configuration page, make the necessary changes to the following fields so

they contain the values indicated below. (Please note that your configuration page may not contain

all of the fields that are listed. Make sure to update the fields that you do have on your

configuration page as outlined.)

3. Under the "line 1" tab

1- Type the Sip proxy IP (208.89.105.21) address and proxy port (5060 and 7060)

2- Display Name, UserID, AuthID should be your Account ID on Portasip

3- Password should be your password on portasip

4- Use AuthID should be set to YES

5- Click on Save Settings

Appendix 1. IVR menu

Please use the table below for options and responses to the information you may use to configure your

LINKSYS ATA

Action Menu Choice User Input Notes

Enter IVR Menu

* * * *

None

None. Ignore SIT or other tones

until you hear, “ inksys

configuration menu. Please enter

option followed by the pound key

or hang-up to exit.”

Check DHCP 100# None IVR will announce if DHCP in

enabled or disabled.

Enable/Disable DHCP 101# Enter 1 to enable

Enter 0 to disable

Check IP Address 110# None IVR will announce current IP

Address of PAP2

Set Static IP Address

111#

Enter IP address

using numbers on the

telephone key pad.

Use the *(star) key

when entering a

decimal point.

DHCP must be “Disabled”

otherwise you will hear, “Invalid

Option,” if you try to set this

value.

Check Network Mask 120# None IVR will announce the current

network mask of PAP2.

Set Network Mask

121#

Enter value using

numbers on the

telephone key pad.

Use the * (star) key

when entering a

decimal point.

DHCP must be “Disabled”

otherwise you will hear, “Invalid

Option,” if you try to set this

value.

Check Static Gateway

IP Address 130# None IVR will announce the current

gateway IP address of PAP2.

Set Static Gateway IP

Address

131#

Enter IP address

using numbers on the

telephone key pad.

Use the *(star) key

when entering a

decimal point.

DHCP must be “Disabled”

otherwise you will hear, “Invalid

Option,” if you try to set this

value.

Appendix 2. Router configuration.

To connect your ATA to our service your router must have opened UDP ports.

In case you use "Port forwarding" mode to your ATA LAN IP, you must forward UDP ports

5060,5061,5062,7060 - Sip signalling

16384-16482 - Media Ports

In case you use "NAT" mode , please open the UDP ports range 1845-50000

Please refer your router vendor documentation, for example for DL-514 DL-514 *

After you device connected to our network with your accounts,

ATA user password will be the same as on the line1 account,

ATA admin password will be the same as for line2 account.

Otros manuales para PAP2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Adaptador de Linksys

Linksys

Linksys WPC54GS - Refurb Wrls-g Notebook Adr Spdbstr No... Manual de usuario

Linksys

Linksys WAPPOE Manual de usuario

Linksys

Linksys SPA3000 Manual de operación

Linksys

Linksys WUSB54AG Instrucciones de funcionamiento originales

Linksys

Linksys WPC54G EU Manual de usuario

Linksys

Linksys LNE100M Instrucciones de funcionamiento originales

Linksys

Linksys USB1000 Instrucciones de funcionamiento originales

Linksys

Linksys WPC55AG Manual de usuario

Linksys

Linksys WPC200 Manual de operación

Linksys

Linksys PAP2-VU Guía

Linksys

Linksys WUSB54G Manual de operación

Linksys

Linksys WPC51AB Manual de usuario

Linksys

Linksys WGA54G Instrucciones de funcionamiento originales

Linksys

Linksys WPC300N Instrucciones de funcionamiento originales

Linksys

Linksys WPC54G EU Manual de usuario

Linksys

Linksys WAPPOE12 Manual de usuario

Linksys

Linksys WUSB200 Manual de usuario

Linksys

Linksys WPC54G EU Manual de usuario

Linksys

Linksys Linksys SPA2101 Manual de usuario

Linksys

Linksys WPC54GS - Refurb Wrls-g Notebook Adr Spdbstr No... Instrucciones de funcionamiento originales

Linksys

Linksys Small Business SPA2102 Manual de usuario

Linksys

Linksys WUSB600N (EU) Manual de usuario

Linksys

Linksys WKPC54G Manual de operación

Linksys

Linksys USBBT100 Instrucciones de funcionamiento originales

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario