LiniLED Side TWW 1200 Manual de usuario

V DC

UV RESISTANT

GLOW WIRE

850 °C

FROST

RESISTANT

CLEANING AGENTS

RESISTANT

IP40/IP68 SWIMMING POOL

ENVIRONMENT

IK08 SWIMMING POOL

SUBMERSIBLE

MAC

ADAM

S D C M

BEND RADIUS

30 mm CRI

80+

System

RoHS SEA WATER

RESISTANT

V301220

LED strip manual

liniLED® Side TWW/TW 1200

Technical notes 3

Technical specications 4

Product drawings 4

Maximum cable length 5

Area advice 6

Product care and handling 7

Cutting instructions 8

Solder 9

Connect IP40 11

Uninstalling the connector 13

Welded connector 14

Power and connection diagram 15

Symbols 16

Side TWW/TW 1200

Manual | liniLED® Side TWW/TW 1200 3

Read the instructions and safety precautions before installation, usage and storage of the products to secure safety of the user and reliability of the product.

- Hand over the instructions to the end user and those responsible for installation and usage.

- Triolight B.V. cannot be held responsible for improper handling, product installation, usage or storage.

Handling

- Handle with care.

- The product may not be modied or converted otherwise than prescribed.

- Products are transported in proper packaging. Products should remain packed until installation.

- Take ESD (Electrostatic Discharge) protection measures when handling liniLED® products.

- The products and their components may not be exposed to mechanical, static loads and other tension/compression other than from the product itself.

Installation

- Attention: The power has to be switched o the main power supply or the connection before installation. Not doing so may damage the product.

- Use a suitable LED power supply/driver: 24 V DC constant voltage. Do not drive the product on other voltages than described in their datasheet/products

specications.

- Installation has to be done by a certied professional with knowledge of electrical circuits or a specialised maintenance person known with valid directives.

- General and local construction-, safety- and installation regulations should be respected.

- Use only supplied parts, accessories and required tools as prescribed in the installation manual to guarantee a safe installation and use of the product.

- Products may solely be installed in the areas according to their prescribed IP-rating, IK-rating, temperature range and chemical resistances.

- The LED strip should be installed on an adequate cooling body for proper heat dissipation to ensure smooth operation and long lifetime.

- Do not fasten anything to the product. The same applies when hanging.

- Do not install the product in the following cases:

- Damage is visible on the product or its cables.

- The inside of the product is moistened or dirty.

- The product or its cables have been modied. This could lead to an electrical shock or a short circuit may occur.

- Children may not play unsupervised with electrical products as they cannot judge the dangers in dealing with electrical circuits correctly.

- Use proper mounting surfaces when installing in environments with large variations in temperature and operating lengths more than 2 metres. This should

absorb the stress of any dierence in expansion.

Operation and use

Solely use the product when it’s working correctly. If not, switch the power o immediately and ask an electrical specialist for advice in the following cases:

- Damage is visible on the product and/or the product does not function.

- The product is overheating and/or smoke or steam rises from the product.

- Crackling sounds are noticeable.

Repairs on the installation may only be performed by qualied electricians. Product repairs may solely be done by Triolight B.V.

Cleaning and maintenance

- Attention: Disconnect the power before maintenance and cleaning.

- Dust and dirt accumulated over time should be removed from the light emitting surface to assure optimal functioning of the product.

- Paints, solvents and corrosive cleaning chemicals may not contact and thus aect the product.

Environment and waste

- Exterior decorative lighting should only be used after sunset.

- This product may not be treated as household waste. Dispose of the material through the waste recycling of electrical and electronic equipment.

Warranty

This product comes with a 2 year warranty. Warranty void if:

- The installation guide has not been consulted (installation mistake).

- The installation is not done by a certied installer.

- Local rules and guidelines are not respected.

- The invoice cannot be shown and/or has been altered.

- Damage is caused by negligence, abnormal use or improper handling, use, maintenance and/or cleaning of the product.

Technical notes

Manual | liniLED® Side TWW/TW 1200

1. Colour temperature 2700K-6500K TW 4000

2. LED strip length 1 m 1,5 m 2,1 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 9.7 m 19.8 m 6.0 m 12.8 m 3.9 m 8.7 m

0.75 mm - 0.023 Ω/m 14.5 m 29.7 m 9.1 m 19.2 m 5.9 m 13.1 m

1.00 mm - 0.018 Ω/m 19.3 m 39.5 m 12.0 m 25.5 m 7.9 m 17.5 m

1.50 mm - 0.012 Ω/m 29.1 m 59.4 m 18.1 m 38.3 m 11.8 m 26.3 m

2.50 mm - 0.007 Ω/m 48.4 m 98.9 m 30.1 m 63.8 m 19.7 m 43.7 m

Tunable Warm White

1. Colour temperature 2200K-3500K TWW 1200

2. LED strip length 1 m 2 m 5 m 9 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 34.4 m 67.2 m 16.6 m 33.0 m 5.9 m 12.4 m 2.7 m 6.3 m

0.75 mm - 0.023 Ω/m 51.7 m 101.0 m 24.9 m 49.5 m 8.8 m 18.6 m 4.0 m 9.5 m

1.00 mm - 0.018 Ω/m 68.7 m 134.2 m 33.1 m 65.8 m 11.7 m 24.8 m 5.4 m 12.6 m

1.50 mm - 0.012 Ω/m 103.3 m 201.9 m 49.7 m 99.0 m 17.6 m 37.3 m 8.1 m 19.0 m

2.50 mm - 0.007 Ω/m 171.9 m 336.0 m 82.8 m 164.8 m 29.3 m 62.1 m 13.4 m 31.6 m

Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).

1. Colour temperature 2700K-6500K TW 1200

2. LED strip length 1 m 2 m 5 m 9 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 37.5 m 73.2 m 18.1 m 36.0 m 6.5 m 13.6 m 3.0 m 7.0 m

0.75 mm - 0.023 Ω/m 56.3 m 110.0 m 27.2 m 54.0 m 9.7 m 20.4 m 4.5 m 10.5 m

1.00 mm - 0.018 Ω/m 74.9 m 146.2 m 36.2 m 71.8 m 12.9 m 27.2 m 6.0 m 14.0 m

1.50 mm - 0.012 Ω/m 112.7 m 219.9 m 54.4 m 108.0 m 19.5 m 40.9 m 9.1 m 21.0 m

2.50 mm - 0.007 Ω/m 187.6 m 366.0 m 90.6 m 179.8 m 32.4 m 68.1 m 15.1 m 35.0 m

1. Colour temperature 2700K-6500K TW 2000

2. LED strip length 1 m 2 m 3 m 4.5 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 20.7 m 41.0 m 9.7 m 19.9 m 6.1 m 12.8 m 3.6 m 8.1 m

0.75 mm - 0.023 Ω/m 31.1 m 61.6 m 14.6 m 29.8 m 9.1 m 19.2 m 5.4 m 12.2 m

1.00 mm - 0.018 Ω/m 41.4 m 81.8 m 19.4 m 39.6 m 12.1 m 25.6 m 7.2 m 16.2 m

1.50 mm - 0.012 Ω/m 62.3 m 123.1 m 29.2 m 59.6 m 18.2 m 38.5 m 10.8 m 24.4 m

2.50 mm - 0.007 Ω/m 103.6 m 204.9 m 48.6 m 99.2 m 30.3 m 64.0 m 18.0 m 40.5 m

1. Colour temperature 2700K-6500K TW 3000

2. LED strip length 1 m 2 m 3 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 12.2 m 24.6 m 5.5 m 11.7 m 3.2 m 7.4 m

0.75 mm - 0.023 Ω/m 18.3 m 37.0 m 8.2 m 17.5 m 4.8 m 11.0 m

1.00 mm - 0.018 Ω/m 24.4 m 49.2 m 10.9 m 23.3 m 6.4 m 14.7 m

1.50 mm - 0.012 Ω/m 36.7 m 74.0 m 16.4 m 35.1 m 9.7 m 22.1 m

2.50 mm - 0.007 Ω/m 61.0 m 123.1 m 27.3 m 58.4 m 16.1 m 36.8 m

Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).

1= Select colour temperature.

2 = Select LED strip length.

3= Select output voltage.

4= Select cable cross section.

Result = Maximum cable length based

on the cable thickness and power supply

voltage.

1. Colour temperature 2700K-6500K TW 4000

2. LED strip length 1 m 1,5 m 2,1 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 9.7 m 19.8 m 6.0 m 12.8 m 3.9 m 8.7 m

0.75 mm - 0.023 Ω/m 14.5 m 29.7 m 9.1 m 19.2 m 5.9 m 13.1 m

1.00 mm - 0.018 Ω/m 19.3 m 39.5 m 12.0 m 25.5 m 7.9 m 17.5 m

1.50 mm - 0.012 Ω/m 29.1 m 59.4 m 18.1 m 38.3 m 11.8 m 26.3 m

2.50 mm - 0.007 Ω/m 48.4 m 98.9 m 30.1 m 63.8 m 19.7 m 43.7 m

Tunable Warm White

1. Colour temperature 2200K-3500K TWW 1200

2. LED strip length 1 m 2 m 5 m 9 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 34.4 m 67.2 m 16.6 m 33.0 m 5.9 m 12.4 m 2.7 m 6.3 m

0.75 mm - 0.023 Ω/m 51.7 m 101.0 m 24.9 m 49.5 m 8.8 m 18.6 m 4.0 m 9.5 m

1.00 mm - 0.018 Ω/m 68.7 m 134.2 m 33.1 m 65.8 m 11.7 m 24.8 m 5.4 m 12.6 m

1.50 mm - 0.012 Ω/m 103.3 m 201.9 m 49.7 m 99.0 m 17.6 m 37.3 m 8.1 m 19.0 m

2.50 mm - 0.007 Ω/m 171.9 m 336.0 m 82.8 m 164.8 m 29.3 m 62.1 m 13.4 m 31.6 m

Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).

12.5

Products drawings

Technical specications

2200K - 3500K

Tunable Warm White 1200

2700 - 6500K

Tunable White 1200

Product code [m]

12469

11993

Power (24V DC)

11.3 W/m

10.3 W/m

Power (25V DC)

11.8 W/m

10.7 W/m

CCT

2200 - 3500K

2700 - 6500K

CRI

>80

Luminous ux

709 lm/m

681 lm/m

Luminous eciency

63 lm/W

66 lm/W

Spool length

Max. 45 m

Section length

75 mm

LED type

3014

Number of LEDs

12 per section/160 per metre

Max. connection length

9 m

Min. operating voltage

23V DC

Max. operating voltage

25V DC

Beam angle

55°

Dimensions

12 x 12 mm

Dimmable

PWM dimming, 24V DC Common Anode

MacAdam Steps

3 MacAdam ellipse per single channel, resulting in combined values of up to 3.8

Weight

150 gram per metre

Expected lifetime

L80/B10 > 60,000 hrs @ Tc = 40°C

Ingress protection

IP40/IP67/IP68

Storage temperature

-30°C ... 55°C

Operating temperature

-30°C ... 55°C

Minimum bending radius

30 mm

CCT Warm White

2173 K

2717 K

Power 2700 K

6.1 W/m

5.3 W/m

Flux 2700 K

363 lm/m

358 lm/m

CCT Cold White

3380 K

6714 K

Power 6500 K

5.2 W/m

5.0 W/m

Flux 6500 K

402 lm/m

368 lm/m

1Typical measured values are given, which due to tolerances in components and production process can vary up to 10%.

2Max. connection length between -30°C and -20°C is 6.3 metres.

3Both channels @ 100% = 4000K (TW) / 2700K (TWW)

4UL certication allows an operable length of TWW; max 8.4 m.

Manual | liniLED® Side TWW/TW 1200 5

1. Colour temperature 2700K-6500K TW 1200

2. LED strip length 1 m 2 m 5 m 9 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 37.5 m 73.2 m 18.1 m 36.0 m 6.5 m 13.6 m 3.0 m 7.0 m

0.75 mm - 0.023 Ω/m 56.3 m 110.0 m 27.2 m 54.0 m 9.7 m 20.4 m 4.5 m 10.5 m

1.00 mm - 0.018 Ω/m 74.9 m 146.2 m 36.2 m 71.8 m 12.9 m 27.2 m 6.0 m 14.0 m

1.50 mm - 0.012 Ω/m 112.7 m 219.9 m 54.4 m 108.0 m 19.5 m 40.9 m 9.1 m 21.0 m

2.50 mm - 0.007 Ω/m 187.6 m 366.0 m 90.6 m 179.8 m 32.4 m 68.1 m 15.1 m 35.0 m

1. Colour temperature 2700K-6500K TW 2000

2. LED strip length 1 m 2 m 3 m 4.5 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 20.7 m 41.0 m 9.7 m 19.9 m 6.1 m 12.8 m 3.6 m 8.1 m

0.75 mm - 0.023 Ω/m 31.1 m 61.6 m 14.6 m 29.8 m 9.1 m 19.2 m 5.4 m 12.2 m

1.00 mm - 0.018 Ω/m 41.4 m 81.8 m 19.4 m 39.6 m 12.1 m 25.6 m 7.2 m 16.2 m

1.50 mm - 0.012 Ω/m 62.3 m 123.1 m 29.2 m 59.6 m 18.2 m 38.5 m 10.8 m 24.4 m

2.50 mm - 0.007 Ω/m 103.6 m 204.9 m 48.6 m 99.2 m 30.3 m 64.0 m 18.0 m 40.5 m

1. Colour temperature 2700K-6500K TW 3000

2. LED strip length 1 m 2 m 3 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 12.2 m 24.6 m 5.5 m 11.7 m 3.2 m 7.4 m

0.75 mm - 0.023 Ω/m 18.3 m 37.0 m 8.2 m 17.5 m 4.8 m 11.0 m

1.00 mm - 0.018 Ω/m 24.4 m 49.2 m 10.9 m 23.3 m 6.4 m 14.7 m

1.50 mm - 0.012 Ω/m 36.7 m 74.0 m 16.4 m 35.1 m 9.7 m 22.1 m

2.50 mm - 0.007 Ω/m 61.0 m 123.1 m 27.3 m 58.4 m 16.1 m 36.8 m

Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).

1= Select colour temperature.

2 = Select LED strip length.

3= Select output voltage.

4= Select cable cross section.

Result = Maximum cable length based

on the cable thickness and power supply

voltage.

1. Colour temperature 2700K-6500K TW 4000

2. LED strip length 1 m 1,5 m 2,1 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 9.7 m 19.8 m 6.0 m 12.8 m 3.9 m 8.7 m

0.75 mm - 0.023 Ω/m 14.5 m 29.7 m 9.1 m 19.2 m 5.9 m 13.1 m

1.00 mm - 0.018 Ω/m 19.3 m 39.5 m 12.0 m 25.5 m 7.9 m 17.5 m

1.50 mm - 0.012 Ω/m 29.1 m 59.4 m 18.1 m 38.3 m 11.8 m 26.3 m

2.50 mm - 0.007 Ω/m 48.4 m 98.9 m 30.1 m 63.8 m 19.7 m 43.7 m

Tunable Warm White

1. Colour temperature 2200K-3500K TWW 1200

2. LED strip length 1 m 2 m 5 m 9 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 34.4 m 67.2 m 16.6 m 33.0 m 5.9 m 12.4 m 2.7 m 6.3 m

0.75 mm - 0.023 Ω/m 51.7 m 101.0 m 24.9 m 49.5 m 8.8 m 18.6 m 4.0 m 9.5 m

1.00 mm - 0.018 Ω/m 68.7 m 134.2 m 33.1 m 65.8 m 11.7 m 24.8 m 5.4 m 12.6 m

1.50 mm - 0.012 Ω/m 103.3 m 201.9 m 49.7 m 99.0 m 17.6 m 37.3 m 8.1 m 19.0 m

2.50 mm - 0.007 Ω/m 171.9 m 336.0 m 82.8 m 164.8 m 29.3 m 62.1 m 13.4 m 31.6 m

Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).

Top/Side Connector (1000 mm)

Result

1. Colour temperature 2700K-6500K TW 1200

2. LED strip length 1 m 2 m 5 m 9 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 37.5 m 73.2 m 18.1 m 36.0 m 6.5 m 13.6 m 3.0 m 7.0 m

0.75 mm - 0.023 Ω/m 56.3 m 110.0 m 27.2 m 54.0 m 9.7 m 20.4 m 4.5 m 10.5 m

1.00 mm - 0.018 Ω/m 74.9 m 146.2 m 36.2 m 71.8 m 12.9 m 27.2 m 6.0 m 14.0 m

1.50 mm - 0.012 Ω/m 112.7 m 219.9 m 54.4 m 108.0 m 19.5 m 40.9 m 9.1 m 21.0 m

2.50 mm - 0.007 Ω/m 187.6 m 366.0 m 90.6 m 179.8 m 32.4 m 68.1 m 15.1 m 35.0 m

1. Colour temperature 2700K-6500K TW 2000

2. LED strip length 1 m 2 m 3 m 4.5 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 20.7 m 41.0 m 9.7 m 19.9 m 6.1 m 12.8 m 3.6 m 8.1 m

0.75 mm - 0.023 Ω/m 31.1 m 61.6 m 14.6 m 29.8 m 9.1 m 19.2 m 5.4 m 12.2 m

1.00 mm - 0.018 Ω/m 41.4 m 81.8 m 19.4 m 39.6 m 12.1 m 25.6 m 7.2 m 16.2 m

1.50 mm - 0.012 Ω/m 62.3 m 123.1 m 29.2 m 59.6 m 18.2 m 38.5 m 10.8 m 24.4 m

2.50 mm - 0.007 Ω/m 103.6 m 204.9 m 48.6 m 99.2 m 30.3 m 64.0 m 18.0 m 40.5 m

1. Colour temperature 2700K-6500K TW 3000

2. LED strip length 1 m 2 m 3 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 12.2 m 24.6 m 5.5 m 11.7 m 3.2 m 7.4 m

0.75 mm - 0.023 Ω/m 18.3 m 37.0 m 8.2 m 17.5 m 4.8 m 11.0 m

1.00 mm - 0.018 Ω/m 24.4 m 49.2 m 10.9 m 23.3 m 6.4 m 14.7 m

1.50 mm - 0.012 Ω/m 36.7 m 74.0 m 16.4 m 35.1 m 9.7 m 22.1 m

2.50 mm - 0.007 Ω/m 61.0 m 123.1 m 27.3 m 58.4 m 16.1 m 36.8 m

Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).

1= Select colour temperature.

2 = Select LED strip length.

3= Select output voltage.

4= Select cable cross section.

Result = Maximum cable length based

on the cable thickness and power supply

voltage.

Maximum cable length

1. Colour temperature 2700K-6500K TW 4000

2. LED strip length 1 m 1,5 m 2,1 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 9.7 m 19.8 m 6.0 m 12.8 m 3.9 m 8.7 m

0.75 mm - 0.023 Ω/m 14.5 m 29.7 m 9.1 m 19.2 m 5.9 m 13.1 m

1.00 mm - 0.018 Ω/m 19.3 m 39.5 m 12.0 m 25.5 m 7.9 m 17.5 m

1.50 mm - 0.012 Ω/m 29.1 m 59.4 m 18.1 m 38.3 m 11.8 m 26.3 m

2.50 mm - 0.007 Ω/m 48.4 m 98.9 m 30.1 m 63.8 m 19.7 m 43.7 m

Tunable Warm White

1. Colour temperature 2200K-3500K TWW 1200

2. LED strip length 1 m 2 m 5 m 9 m

3. Voltage 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC 24 V DC 25 V DC

4. Cable cross section 0.50 mm - 0.035 Ω/m 34.4 m 67.2 m 16.6 m 33.0 m 5.9 m 12.4 m 2.7 m 6.3 m

0.75 mm - 0.023 Ω/m 51.7 m 101.0 m 24.9 m 49.5 m 8.8 m 18.6 m 4.0 m 9.5 m

1.00 mm - 0.018 Ω/m 68.7 m 134.2 m 33.1 m 65.8 m 11.7 m 24.8 m 5.4 m 12.6 m

1.50 mm - 0.012 Ω/m 103.3 m 201.9 m 49.7 m 99.0 m 17.6 m 37.3 m 8.1 m 19.0 m

2.50 mm - 0.007 Ω/m 171.9 m 336.0 m 82.8 m 164.8 m 29.3 m 62.1 m 13.4 m 31.6 m

Note: Calculations are based on a standard connector with 1 metre cable (0.5 mm).

Manual | liniLED® Side TWW/TW 1200

Depending on the installation area of the liniLED® LED strip we oer a range of IP20, IP40 and IP68 solutions to cope with external factors. Below the dierent

connectors are displayed for use in dierent environments. See corresponding pages or individual product manual for further instructions.

Indoor environment | (IP20)

Solder

Indoor environment | (IP40) | liniLED® Side Connector set.

Prod. code: TW 11193, 11194 (1m, 5m) | RGB 11206, 11207 (1m, 5m).

Wet environment | (IP68) | liniLED® Cast Joint IP68

Product code: 11533

See Manual liniLED® Cast Joint IP68 for installation instructions.

Submersible, chlorine resistant | (IP68) | Welded Connector

Product code: 12293 1m

12294 5m

The connector is pre-assembled to the LED strip.

Area advice

Manual | liniLED® Side TWW/TW 1200 7

Product care and handling

30 mm

Maximum bending radius is 30 mm. Solely bend up or downward. Do not compress or stretch the LED strip.

Do not bend the LED strip sidewards. Do not twist the LED strip.

The LED strip has to be unreeled on a horizontal surface at the time of installation. Do not unreel the spool of LED strip before installation.

Manual | liniLED® Side TWW/TW 1200

Work in an ESD protected environment. Make use of an anti-static

strap.

Turn o the power before cutting the LED strip.

Side view | Make sure the cut is vertical as illustraded in the image

above.

Top view | Make sure the cut is vertical as illustraded in the image

above.

Top view | Only cut on the dotted lines to prevent damaging the

LED strip.

Dispose of the unnecessary material through waste recycling of

electrical and electronic equipment.

Cutting instructions

Manual | liniLED® Side TWW/TW 1200 9

Place the liniLED® LED strip on the base of the cutting tool. Not doing so may result in a deformed LED strip.

Cutting instructions

Manual | liniLED® Side TWW/TW 1200

Solder

Work in an ESD protected environment. Make use of an anti-static

strap.

Turn o the power before cutting the LED strip. Make sure the wires

are not under electric current.

0.5 mm

8 mm

We advise to use a cable with an area not larger then 0.5 mm2.Make sure you solder the wires on the right pads.

Red wire = + | White wire = C (6500K) | Yellow wire = W (2700K)

Isometric view | Only cut the LED strip extrusion on the dotted line

of the extrusion to prevent damaging the PCB. Carefully cut away

this part of the extrusion.

Isometric view | Do not cut the PCB!

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de liniLED

liniLED

liniLED Diffuse Series Manual de usuario

liniLED

liniLED Side Photon 1200 Manual de usuario

liniLED

liniLED PCB Mono White G1 Series Manual de usuario

liniLED

liniLED Top Power Colour Manual de usuario

liniLED

liniLED Ultra Warm White 2400K Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

liniLED Side TWW 1200 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas