Lightspeed DELTA PA Manual de usuario
User Manual
Portable Amplification System
DELTA PA
ON
TABLE OF CONTENTS
SECTION 1: 4 Safety Instructions
5 System Components and Unpacking
Overview 6 Optional Components
7 Top Panel Wireless Receiver Controls
8 Top Panel Controls & Connections
9 Rear Panel Controls & Connections
10 Installing or Replacing Receiver Module
SECTION 2: 11 Step 1. Connecting the DELTA PA Receiver
to a Power Supply
Set-up & Use 12 Step 2A. Setting up one DELTA PA Receiver
13 Step 2B. Using More Than One DELTA PA
Receiver
Handheld Transmitter
14 Step 3. Channel Selection
15 Step 4. Battery Life & Battery Type
16 Step 5. Replacing Battery
17 Step 6. Recharging Batteries
Belt-pack
18 Step 7. Connecting & Placement
19 Step 8. Channel Selection
20 Step 9. Gain Adjust
21 Step 10. Battery Life Indicator & Type
22 Step 11. Replacing Batteries
23 Step 12. Recharging Batteries
24 Daily Use Instructions
SECTION 3: 25 Hand Held Microphone Transmitter
Optional Accessories 26 Belt-Pack Transmitter
SECTION 4: 27 Troubleshooting Guide
Troubleshooting
SECTION 5: 28 Warranty Statement
Warranty &
Specications
29 Safety Warnings
30 System Specifications
4
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use the apparatus near
water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in
accordance with the
manufacturer’s instructions.
8. Do not install near any heat
sources such as radiators,
heat registers, stoves, or
other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety
purpose of the polarized
or grounding-type plug.
A polarized plug has two
blades with one wider than
the other. A grounding- type
plug has two blades and a
third grounding prong. The
wide blade or the third prong
is provided for your safety. If
the provided plug does not
fit into your outlet, consult an
electrician for replacement of
the obsolete outlet.
10. Protect the power cord
from being walked on or
pinched particularly at plugs,
convenience receptacles, and
the point where they exit from
the apparatus.
11. Only use attachments/
accessories specified by the
manufacturer.
12. Use only with a cart, stand,
tripod, bracket or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during
lightning storms or when
unused for long periods of
time.
14. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus
has been damaged in any
way, such as power-supply
cord or plug is damaged,
liquid has been spilled or
objects have fallen into the
apparatus, the apparatus
has been exposed to rain or
moisture, does not operate
normally, or has been
dropped.
15. When the mains plug or
appliance coupler used as
the disconnect device, it shall
remain readily operable.
16. Please keep the unit in a good
ventilation environment.
5
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
SECTION 1:
OVERVIEW
SYSTEM COMPONENTS AND UNPACKING
The standard conguration of the DELTA PA will contain:
DELTA PA Carry Case
DELTA PA Public
Address System
and Power Supply
TX-HM016
Transmitter
ON
6
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
OPTIONAL COMPONENTS
Optional equipment which may be part of your DELTA PA system:
Individual Components
RX-DPA016R 16 Channel UHF Receiver Module
TX-HM016 16 Channel UHF Handheld Transmitter
AC-MH7 Mic Clip for HM016 Handheld Transmitter
TX-BP016 16 Channel UHF Belt-Pack Transmitter
BC-TX900 Battery Charger for BP016 or HM016
MC- 831S Audio-Technica 831 Lapel Mic
MC-TK270S Lightspeed Noise-cancelling Headset Mic
PS-24V-2.5-A AC Power Supply
BA-NH1 AA NiMH Rechargeable Battery
AC-SPDELTA-X6 Carry Bag for DELTA PA
AC-PWR-NA AC North American Power Cable
Optional Accessories
CA-GTC900 Guitar/aux In Cable for BP016
AC-TWBRK Speaker Stand Bracket
AC-SS1 Tripod Speaker Stand
AC-SPSS1 Carry Bag for Tripod Speaker Stand
MC-H10 Wired Dynamic Handheld Mic
TX-BP016 Transmitter
and Charger
MC-TK270S Noise-
Cancelling Headset
Microphone
MC-831S Audio
-Technica 831
Lapel Mic
7
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
TOP PANEL: WIRELESS RECEIVER CONTROLS
5. TRANSMITTER LOW BATTERY
INDICATOR: This LED will light
to indicate the batteries in the
corresponding transmitter are
low.
6. SCAN: Press this button to auto-
matically select a channel that is
free from interference.
7. SQUELCH LEVEL ADJUSTMENT:
Covered with a plastic cap, the
squelch is adjusted at the factory
to provide the best signal level
and minimum noise. There is no
need to adjust the squelch level
in the field.
1. WIRELESS RECEIVER 1: One or
two wireless receiver modules are
located at the top panel.
2. CHANNEL DISPLAY: An LED
readout of the receiver module
indicates which channel you are
on.
3. CHANNEL CONTROL (1-16): The
left button increments the channel
number (1-16). Each touch of the
button moves the number up one
until it gets to sixteen. The right
button decrements the channel
number (16-1).
4. RF CHANNEL A/B INDICATOR:
The “A” LED lights up indicating
the A channel tuner is receiving
the strongest RF signal. The “B”
LED lights up indicating the “B”
channel tuner is receiving the
strongest RF signal.
POWER
CHARGE
RED: LOW BATT GREEN: ON
RED: CHARGING GREEN: FULL
RECVR 1
RECVR 2
RECVR 2
O/I
POWER/
RECVR 1
1
2
36
5
7
4
8
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
TOP PANEL CONTROLS AND
CONNECTIONS
1. BASS: Controls the level of low
frequency sound output for the
system.
2. TREBLE: Controls the level of
high frequency sound output for
the system.
NOTE: Reducing Feedback
The BASS and TREBLE controls
can be used to reduce feedback
(“squealing” or “howling”). If you
hear high-pitched squealing, lower
the treble setting. If you hear low-
pitched howling, lower the bass
setting.
3. AUX IN/MIC IN: Controls the
volume of a wired microphone
plugged into MIC IN on the back
of the system and the volume of
an auxiliary piece of equipment
plugged into the AUX IN on the
back of the system.
4. WIRELESS RECVR 2: Controls the
volume of Wireless Microphone
2 if a second wireless receiver is
installed.
5. POWER/WIRELESS RECVR 1:
Turn this knob clockwise to power
up the system. Rotate to adjust the
volume of Wireless Microphone 1.
6. POWER LED: Green = Power On.
Red = Low Battery
7. CHARGING LED: Green = Full
Charge. Red = Charging
1
2
3
7
5
4
POWER
CHARGE
RED: LOW BATT GREEN: ON
RED: CHARGING GREEN: FULL
RECVR 1
RECVR 2
RECVR 2
O/I
POWER/
RECVR 1
6
9
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
1
2
3
5
4
REAR PANEL CONTROLS AND CONNECTIONS
a line level output signal that
can be connected to a recorder,
assistive listening device, etc.
6. SPEAKER OUT (SWITCHED): This
¼” jack can be used to connect
to an external passive speaker.
[NOTE: connection to this jack will
mute the internal speaker of the
DELTA PA.]
*Note: Wiring to these terminals
should follow the Class 2 wiring
methods as outlined in the
National Electric Code.
7. FUSE: The fuse holder is
accessible using a flat-blade
screwdriver. Push in and rotate ¼
turn counterclockwise to remove.
[NOTE: replacement is a 3.15A SB
250V slow blow fuse.]
8. DC POWER: This jack provides
a connection for the DELTA PA
power supply.
1. MIC IN: This ¼” jack provides
an input for a wired handheld
microphone.
2. AUX IN: This 3.5 mm jack
provides an input for audio from
an external device, such as a
CD player, MP3 player, TV/VCR,
computer, etc.
3. AUX OUT: This 3.5 mm jack
provides an adjustable-level
audio output that can be
connected to a recorder or
assistive listening device.
4. AUX OUT VOLUME: This knob
controls the level of the 3.5 mm
AUX OUT jack. Counterclockwise
represents a microphone level
signal, while fully clockwise
represents a line level signal.
5. AUX OUT: This ¼” jack provides
6
7
8
10
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
INSTALLING OR REPLACING A RECEIVER
MODULE
NOTE: Make sure the DELTA PA is
turned off.
1. Remove the two screws securing
the module panel using a small
phillips head screwdriver.
2. Remove the module from the
enclosure by carefully inserting
the blade of a small, flat-blade
screwdriver under the face plate
edge and nudging it upward.
3. Grasp the edges of the module
with both hands and slide
it out.
4. Install the new module by
aligning it with the guide rails and
sliding all the way in to engage
the connector at the rear of the
module.
5. Replace the two screws.
POWER
CHARGE
RED: LOW BATT GREEN: ON
RED: CHARGING GREEN: FULL
RECVR 1
RECVR 2
RECVR 2
O/I
POWER/
RECVR 1
Otros manuales para DELTA PA
1
Tabla de contenidos
Otros manuales de Sistema de altavoces de Lightspeed
Manuales populares de Sistema de altavoces de otras marcas
Sondpex
Sondpex Active Speaker System and Digital Music... Manual de usuario
JVC
JVC NX-PN7 Manual de usuario
Marshall Amplification
Marshall Amplification AR-DM61-BT Manual de usuario
Yamaha
Yamaha NX-A01 - Speaker Sys Manual de usuario
SE Audiotechnik
SE Audiotechnik I-LINE Manual de usuario
Gemini
Gemini WRX-843 Series Manual de usuario