Lightolier LYTECASTER 1000LV Manual de usuario

SEE BACK PAGE FOR LAMPING INSTRUCTIONS

READ AND UNDERSTAND THESE INSTRUCTIONS

BEFORE INSTALLING LUMINAIRE.

This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.

To assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at main power supply before proceeding.

Retain these instructions for maintenance reference.

INSTALLATION PROCEDURE FOR: LYTECASTER® 1000LV, 1000LVE1, & 1000LVE2 LOW VOLTAGE

FRAME-IN KITS

CAUTION: USE ONLY WITH REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURER’S TRIMS

MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

INSTRUCTION SHEET NO.

IS:1000LV

B0607 Page 1 of 2

A COMPANY

631 Airport Road, Fall River, MA 02720

CAUTION: BEFORE INSTALLING FRAME-IN KIT AND REFLECTOR TRIM, READ ALL MARKINGS ON FRAME-IN KIT AND

REFLECTOR TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION.

WARNING— (RISK OF FIRE) DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR WIRING

COMPARTMENT

NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HEAT.

1. FRAME- IN AND WIRE-IN (Fig. A)

Fasten MOUNTING FRAME to wood joist. Line up bottom edge of

ADJUSTABLE MOUNTING BAR with bottom of wood joist (Fig. E). Wire to

supply leads. (For Cable, use built-in Cable Clamp in J-Box). WHITE

FIXTURE LEAD to NEUTRAL SUPPLY LEAD. BLACK FIXTURE LEAD to

HOT SUPPLY LEAD (120V). BARE FIXTURE WIRE to SUPPLY GROUND

(1000LV only). Use wirenuts (local hardware item). Place all electrical

connections in the J-BOX. Attach J-BOX COVER onto J-BOX.

NOTE: ADJUSTABLE MOUNTING BARS can be extended for 24”

mounting. For suspended ceiling, make certain that the bottom of

MOUNTING FRAME is no higher than 1” above ceiling line (Fig. F)

2. CLOSE- IN (Fig. B)

Install plasterboard, or any other dry type ceiling, as required. Hole in board

must be cut either on the ground or after the board is nailed to the ceiling,

using MOUNTING FRAME opening as a cutting guide. (Make sure ROTO-

CLIPS are rotated out of hole area to be cut.) (Fig. G).

*Lightolier also offers a hole cutter (HC-356) that can be purchased

separately to assist with quick, clean trim installations. In this case, follow

the hole cutting directions supplied with HC-356.

3. SNAP-IN (Fig. C).

→

4. PUSH- UP (Fig. D).

NOTE: For wet plaster ceiling, use Plaster Ring Accessory No.1959

(order separately).

SEE SEPARATE

REFLECTOR TRIM

INSTRUCTION SHEETS

INSTALLATION PROCEDURE FOR: LYTECASTER®

1000LV, 1000LVE1 & 1000LVE2 LOW VOLTAGE FRAME-IN

KITS (CONTINUED)

INSTRUCTION SHEET NO.

IS:1000LV

B0607 Page 2 of 2

A COMPANY

631 Airport Road, Fall River, MA 02720

LAMPING (Fig. H)

NOTE: Socket manufacturers have suggested that socket may fail after 3 to 6 relampings. If

this occurs, socket can be replaced by disconnecting male connectors (attached to socket

leads) from female connectors (attached to fixture leads) and replacing it with a new socket

procured through LIGHTOLIER (Fig. H)

1. Make sure that power is OFF when lamping or relamping. Remove LAMP RING

from SOCKET CUP by pulling straight down.

2. Insert LAMP (MR-16) between LAMP SPRINGS until face of lamp sits firmly on GLASS

LAMP GUARD

(Fig. I.)

3. Attach SOCKET to bi-pin prongs on LAMP.

4. Insert LAMP RING with LAMP and GLASS LAMP GUARD back into SOCKET CUP.

NOTE: 1. LOW VOLTAGE FIXTURES should be dimmed only with special dimmers

intended specifically for that purpose. Use Lightolier Lytemode, Scenist, Crescendo VA,

Neptune VA, Precision VA, Easyset VA, Sunrise VA, Radiant VA or equivalent products

by others or variable autotransformers or electronic dimmers intended for use with low

voltage fixtures. 2. Low voltage fixtures may produce audible sound when used with

dimmers, which may be objectional in acoustically critical areas.

TRANSFORMER REPLACEMENT (1000LV, 1000LVE1 and 1000LVE2)

1. Make sure power is off.

2. Remove REFLECTOR TRIM from ceiling.

3. Rotate ROTO CLIPS out of hole area.

4. Remove J-BOX COVER nearest ceiling opening by lifting SPRING.

5. Unsplice all wiring.

6. Remove TRANSFORMER ASSEMBLY from J-BOX by pulling SPRING upward. (Fig. K).

7. Place TRANSFORMER ASSEMBLY thru ceiling opening.

8. Remove TRANSFORMER and TRANSFORMER COVER by straightening TABS with pliers

and removing SCREWS. For 1000LVE1 and 1000LVE2, remove TRANSFORMER by

removing NUTS.

9. Install the new TRANSFORMER on the U-shaped holder with SCREWS and re-tab to the

remaining half of the TRANSFORMER ASSEMBLY. For 1000LVE1 and 1000LVE2, install

the new TRANSFORMER, securing with NUTS.

10. Reassemble TRANSFORMER ASSEMBLY to J-BOX by placing J-BOX COVER TABS into

J-BOX SLOTS and snapping onto SPRING (Fig. K).

11. Rewire Fixture:

A. Splice transformer red leads to white socket leads.

B. Splice transformer black lead to thermal protector blue lead.

C. Splice transformer and thermal protector white leads to supply common lead.

D. Splice thermal protector black lead to supply black lead.

12. Replace J-BOX COVER.

13. Install REFLECTOR TRIM.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Lightolier

Lightolier

Lightolier UCS Manual de usuario

Lightolier

Lightolier Paraplus PPH1G6FW154 Manual de usuario

Lightolier

Lightolier Lytespan DR2C Manual de usuario

Lightolier

Lightolier LP-7 Manual de usuario

Lightolier

Lightolier Soli 48021ALU Manual de usuario

Lightolier

Lightolier Lytespan 23F70T6 Manual de usuario

Lightolier

Lightolier Calculite 7794QD Manual de usuario

Lightolier

Lightolier LSB-3 Manual de usuario

Lightolier

Lightolier Lytespan 8105 Manual de usuario

Lightolier

Lightolier Calculite ProSpec PB2P3810 Manual de usuario

Lightolier

Lightolier FA01 Manual de usuario

Lightolier

Lightolier Lytespan 83T4S Manual de usuario

Lightolier

Lightolier Lighting Systems LP-1 Manual de usuario

Lightolier

Lightolier Calculite ProSpec PA2M1675 Manual de usuario

Lightolier

Lightolier IS_ALETTA-ROW Manual de instrucciones

Lightolier

Lightolier Lighting Systems Baselyte-BSL30 Manual de usuario

Lightolier

Lightolier Lytespan DRL70 Manual de usuario

Lightolier

Lightolier PLA2G9LP32U Manual de usuario

Lightolier

Lightolier Baselyte-BSL7 Manual de usuario

Lightolier

Lightolier DPB2S18LS332 Manual de usuario

Lightolier

Lightolier Lytespan 8727 Manual de usuario

Lightolier

Lightolier Lytecaster 1178LX Manual de usuario

Lightolier

Lightolier LP-19 Manual de usuario

Lightolier

Lightolier Lighting Systems EG2-3 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario