Lightolier POWER EXTENSION CONNECTOR Manual de usuario

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Accesorios de Lightolier

Lightolier

Lightolier Lytecaster 3401MREX Manual de usuario

Lightolier

Lightolier Lytespan 8317 Manual de usuario

Lightolier

Lightolier Lytecaster 1027 Manual de usuario

Lightolier

Lightolier 1101HCB Manual de usuario

Lightolier

Lightolier 1105 Manual de usuario

Lightolier

Lightolier Lytespan 8676B Manual de usuario

Lightolier

Lightolier Calculite GC Manual de usuario

Lightolier

Lightolier Lytecaster 1152 Manual de usuario

Lightolier

Lightolier 6280 Manual de usuario

Lightolier

Lightolier SL111B2 Manual de usuario

Lightolier

Lightolier Lytespan 24MHT45RF Manual de usuario

Lightolier

Lightolier Lytecaster 1104F13ESR Manual de usuario

Lightolier

Lightolier Calculite FA-EM Manual de usuario

Lightolier

Lightolier Lytespan 8273B Manual de usuario

Lightolier

Lightolier LG Series Manual de usuario

Lightolier

Lightolier Calculite C6P38A Manual de usuario

Lightolier

Lightolier LYTESPAN CONVENIENCE OUTLET Instrucciones de uso

Lightolier

Lightolier Tangent FX16SC Manual de usuario

Lightolier

Lightolier Lytecaster 1104F18ESR Manual de usuario

Lightolier

Lightolier Calculite C6CFL32 Manual de usuario

Lightolier

Lightolier Lytespan 6350 Manual de usuario

Lightolier

Lightolier 40829U Manual de usuario

Lightolier

Lightolier IS_CD7-STEM Manual de instrucciones

Lightolier

Lightolier C6TCAA Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

P

READANDUNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE lNSTRUCTfON SHEET NO.

This fixture is intended for installation in accordanrx?with the National Electrical Code and local regulations.

To assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. Toprevent electrical shock, turnoff electricity at fuse box before proceeding. IS:6046

Retain these instructions for maintenance reference. R0992 Page 1of 2

POWER EXTENSION CONNECTOR

FOR USE WITH BASIC LYTESPAN@TRACK SYSTEMS ONLY.

The POWER EXTENSION CONNECTOR allows power to be jumped from one

track, around or through structural obstacles, to another track unit. [t replaces the

DEAD END COVER at the end of an Individual track unit or arun of track units.

Power can be fed intoor removedfromthe POWER EXTENSION CONNECTOR

by using any of the power feed-in kits available for Basic Lytespan. Afew examples

are shown here.

CAUTION:

.TURN OFF POWER AT FUSE BOX BEFORE INSTALLING

TRACK.

“INSTRUCTIONS FOR GROUNDING PER INSTRUCTION SHEET e

B

TRACK

OF THE FEED-IN KIT MUST BE FOLLOWED. FAILURE TO DO \_

UNIT

SO MAY RESULT IN AHAZARDOUS CONDITION, DEAD END

COVER

~USE ONLY #12 GA. SOLID COPPER WIRE IN CONNECTORS TO

MAINTAIN PROPER RATING OF TRACK.

.OBSERVE POLARITY, WHITE (NEUTRAL) WIRE MUST BE

CONNECTED TO TERMINAL MARKED “NEUT”. FAILURE TO

OBSERVE POLARITY MAY RESULT IN AN ELECTRICAL

HAZARD,

.DO NOT USE TRACK AS ACONDUIT SUPPORT.

INDEPENDENT CONDUIT SUPPORTS (SUCH AS SUITABLE

CONDUIT STRAPS) MUST BE USED TO AITACH THE CONDUIT

INSTALLATION TO THE BUILDING STRUCTURE.

INSTALLING THE POWER EXTENSION CONNECTOR TRACK

UNIT

1. Remove the DEAD END COVER from the track.

2. Insert the POWER EXTENSION CONNECTOR in place of the DEAD —SCREW

END COVER. Tighten SCREW.

3. Follow the instructions provided with the power feed-in kit being used. POWER EXTENSION

NOTE: Power can be fed into or removed from the POWER CONNECTOR

EXTENSION CONNECTOR by using astandard 1/2” -14 I.P.S.

ELECTRICAL CONNECTOR (not included). See Track Instruction

Sheet 1S:6020.

1-1<> 1=1 iC> LIER“

EWAH?!!WEY%Y