Light-For-Me 2XML Manual de usuario

LIGHT FOR ME

2XML Hand Torch user’s manual

2XML Hand Torch

Please read the following user’s manual carefully before the ﬁrst use of the products and keep it for future

reference. Scuba diving is treated as an extreme sport and requires proper training and certiﬁcation. Using scuba

equipment by an untrained and inexperienced person without proper certiﬁcation may cause health damage and

even risk of death. Light-for-me backup lights are designed to be used underwater only.

Light-for-me Backup XML MINI is powered by 1 x 18650

Li-Ion rechargeable battery. It is recommended to use

battery of high quality and from a reliable source.

Before inserting the battery into the backup’s body, check

its condition - do not use damaged or broken batteries.

The battery should be put into the backup’s body with

the sign – (minus) to the head and with the sign +

(plus) to the inner part of the body (see the photo).

Placing the battery the other way may cause a complete

and irreversible damage to the light diode. Do not force

the battery into the body, it should go in / out easily.

Charge the battery according to the speciﬁcation given by

its manufacturer with an appropriate and approved

charger. 18650 Li-Ion batteries require a dedicated

charger.

Power source

Light-for-me Backup XML Mini is switched on/oﬀ by twisting the head to the

body. To switch the light on, hold the body with one hand and twist the head in a

clockwise direction with the other. To switch the light oﬀ, hold the body with one

hand and twist the head in an anticlockwise direction with the other.

When switching the backup oﬀ under water, stop twisting the moment the light

goes oﬀ. If you continue to twist the head, you may ﬂood the backup.

Do not switch the light on when not in water for more than 5 seconds. It is

allowed to switch the light on to test if it works properly, but for maximum of 5

seconds. Longer use of the light on the surface may cause the LED to get too

warm and get damaged as a result. Do not direct the light into your or anyone

else’s eyes.

Switching on/oﬀ

1/3

The 2XML Hand Torch set consists of:

- 2x Backup XML Mini

- Goodman handle

- Codura cover

Important!

Batteries and charger not included

Set content

2/3

Keep those surfaces clean

for better electrical conductivity

Check sealing orings regulary

and replace them if needed

Tech Speciﬁcations

2XML HAND TORCH

Purpose

Material

Max operating depth

Number of LEDs

LED type

Power

Lumen output

Light angle

Light temperature

Switch type

Max dimensions

Weight w/o batteries

Batteries

main light

anodised aluminium

100m

XML

2 x 10W

max 2400

+/- 5 degrees

6800K

head-to-body twist

120mm (width), 100mm (height)

650g

2 x 18650 Li-Ion (not included)

Before every dive check the condition of orings that seal the body of the backup torch. Torn, cut or damaged orings should

be replaced for a new ones as they may lead to ﬂooding of the backup.

The oring sealing the body to the head should be lightly greased with technical petroleum jelly (pure vaseline) which makes

it easier to operate the light underwater and helps it stay watertight. Remove any dust, mud or sand from the orings before

twisting the body to the head.

From time to time clean the surface that touches the inside of backup head (marked in the drawing) and the silver ring

around the spring inside the backup head. These surfaces need to be clean and grease-free in order for the backup to work

properly.

While slowly twisting the body to the head make sure the sealing orings are correctly placed in their position and are not

twisted or sticking out. Orings should sit ﬁrmly in their grooves and should not be too loose as they may not work properly

underwater.

After each day of diving, rinse the backup in fresh water and dry it. Check the sealing orings and grease them if necessary.

Store the backup with its battery taken out.

Maintenance

Battery should not be longer

than its pocket. It should not go

beyond the marked edge of the

pocket. A longer battery may

cause improper working of the

torch.

Troubleshooting

Problem Solution

I have ﬂooded my torch.

I can see some water inside the

head.

In case of ﬂooding the torch: untwist the head from the body, remove the

battery and dry it, the inside should be rinsed with fresh lukewarm water and

torch should be left open for the time of at least 72 hours. The head should

be left to dry with the glass directed downwards while drying. The ﬂooding of

the head may result in lowering the power of emitted light. Check the battery’s

manufacturer advice for ﬂooding the battery. For safety reason do not use the

battery again. Contact the light-for-me manufacturer.

I charge the batteries full but

still get less burn time than

stated.

It is recommended to use high quality genuine batteries. Burn times given

with each backup torch are based on the data given by their manufacturers.

Burn time may diﬀer +/-10% from the stated one depending on the ambient

conditions when diving and battery- / charger-related issues. If the burn time

is visibly shorter, try the backup with a diﬀerent battery. If in doubt, contact

the light-for-me manufacturer.

The light ﬂashes from time to

time, even with fully charged

batteries.

Check the battery - charge it if necessary; damaged or suspiciously looking

battery should be replaced with a new one. Check the torch with a diﬀerent

battery. Clean the ‘touch surfaces’ described above. Should the issue

continue, contact the light-for-me manufacturer.

I have forgotten to take out the

batteries after my last dive and

the backup does not work now.

Check the battery’s manufacturer for advise. Clean the ‘touch surfaces’

described above. Check the torch with a diﬀerent battery. If the issue

continues, contact the light-for-me manufacturer.

Characteristics:

• cylindrical lithium-ion cell

• nominal voltage around 3.7V

• positive terminal nub at one end and ﬂat negative terminal at the other

• available with an internal protection circuit to prevent over-discharge and shortcircuit damage

• for safety reasons recharging requires use of chargers speciﬁed for these cells

• dimensions: 18.3mm x 65.2mm (diameter x length)

• no memory eﬀect and no scheduled cycling required to prolong the battery's life

• high capacity

• stable discharge voltage

• high voltage / light weight battery

18650 Li-Ion battery

Tabla de contenidos

Otros manuales de Equipo de iluminación de Light-For-Me

Light-For-Me

Light-For-Me ACCU 12V 18Ah Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario