Liene Amber M200 Manual de usuario
User Manual 02
Benutzerhandbuch 16
Manuel de l'utilisateur 29
Manual de usuario 42
Manuale d'uso 55
Please read this Manual carefully before
using the product and keep it properly
User Manual for Amber
M200 Instant Photo Printer
02
Product Overview
Side Door
Power Button
Indicators
Power Indicator
Battery Indicator
Failure Indicator
Wi-Fi Hotspot Indicator
Front Door
Air Vent
Paper
Ejection Slot
Reset Hole
Power Socket
Type-C USB Port
(Not for charging, data only)
Accessory List
Power Adapter x1 Paper Cassette x1
Paper Cassette
Holder
Paper Cassette
Cover
Photo Paper 20
sheetsx1
Ink Cartridge x1
90°
03
Install Ink Cartridge
1Open the side door
2Insert new ink cartridge until the lock is in place
3Close the side door
Refill Photo Paper
1Open the paper cassette cover along the top seam
180°
04
2Load photo paper in the cassette with the glossy side face-up
Note:
1. The maximum of the cassette is 20 sheets of photo papers.
2. Do not touch the area within the crop marks of a photo paper.
3. Undrawing the paper cassette holder makes refilling easy.
3Close the paper cassette cover
Install Paper Cassette
1Undraw the paper cassette holder
2Rotate the holder down 180° to the bottom
90°
05
3Insert the paper cassette into the printer
Replace Ink Cartridge
1Open the side door
2Lift the lock upward to pop out used ink cartridge and take
it out
3Insert new ink cartridge until the lock is in place, then close the
side door
More than 4inchs (10cm)
06
Usage
Working Location
When printing, the photo paper goes back and forth. Please make
sure to leave more than 4inchs (10cm) space behind the printer.
Note: Paper goes in and out for 4 times.
Storage
When the printer is not in use, place the paper cassette on top of
the printer for space saving and easy storage.
The printer has a built-in lithium battery, avoid keeping in high
temperature and high humidity environment. Charge at least once
every 3 months. Do not use after immersion in water.
Instruction for Buttons
1 s
Press and hold Power
Button for 1 second Power on
Press Power Button Power o
3 times
Quickly press Power Button
3 times
Reset printer Wi-Fi hotspot
password
6 times
Quickly press Power Button
6 times Restore factory settings
07
Note:
1. All indicators light on and blink for 2 seconds simultaneously if the factory
settings are restoredsuccessfully.
2. Wi-Fi hotspot indicator blinks for 2 seconds if the printer Wi-Fi hotspot
password is reset successfully. Reset the network only when printer is idle
or there is a printer failure. Default password is 12345678.
3. During printing, printing will not be interrupted when the power button is
pressed.
4. During firmware upgrading, upgrading will not be interrupted when the
power button is pressed.
5. When there is a failure, press the power button to power the printer off.
Then, power the printer on again. The printer will try to fix the problem
automatically after powering on. If fail to power the printer off, please use
a pin to poke the reset hole at the back of the printer to restart.
Power Indicator
Light o Power o
Light on Power on
White light blink Printing
Firmware upgrading
Breath In sleep mode
Note:
•Sleep mode starts after idle for 5minutes. Press Power Button or send a
print job to wake the printer up.
•Auto-power off after idle for 20 minutes.
Failure Indicator
Light o Printer OK
Orange light blink Printer has failed. Follow the APP
prompts to solve problem
Battery Indicator
Light o Fully charged
Orange light on Low battery
White light on Charging
White light blink Battery error state
Orange light blink Battery insucient
08
Wi-Fi Hotspot Indicator
Light o Function o
Orange light on Function on
Blue light on Connected to one or more devices
Orange light blink Function turning on
Usage
1Connect Power Supply
Plug the power jack into the power socket at the back of the printer.
2Power On
• Press the power button to power the printer on.
• Power indicator lights on in white, Wi-Fi hotspot indicator starts
blinking in orange in about 10s, then lights on in orange.
• The printer enters the idle status.
Connect Device Wi-Fi
• Open the WLAN connection on your smartphone, tablet,
computer, etc. and select "Liene Photo Printer [xxxx]".
• The default connection password is 12345678.
• When the Wi-Fi hotspot indicator lights on in blue, it means
successful connection for at least 1 device.
Note:
• You can change the password in the APP.
• Support to connect to a maximum of 5 devices simultaneously.
• [xxxx] refers to the last four digits of the product SN number, which can be
found on the label at the bottom of the printer.
• For Android device, after switching the Wi-Fi signal to the printer Wi-Fi hotspot
signal, it will pop up a message that the internet may not be available.
• Please keep the WLAN connection when using the printer.
• Please download and install the computer driver before connecting to
a computer.
3
09
1Print with “Liene Photo” APP
Search for "Liene Photo" in the App Store or scan the QR code
below to download and install the "Liene Photo" App.
Open "Liene Photo" App and follow the APP prompts to add a
device. You can nd the device in the list on the
home page after it is successfully added.
Note: The actual operation may not match the description
here due to "Liene Photo" APP upgrades and updates.
Please follow the instructions within the current "Liene
Photo" APP to operate.
Make sure that the device is connected to the printer Wi-Fi
hotspot, and the Wi-Fi hotspot indicator lights on in blue.
Follow the operation prompts in the APP to print.
Print from Android Device
Make sure that the device is connected to the printer Wi-Fi
hotspot, and the Wi-Fi hotspot indicator lights on in blue.
Conrm that you agree to use this network.
Open the album and select the photos, then select the printer,
adjust the printing parameters and print. If the printer is not
found, please turn on "Default Print Service".
If the printing interface is not found in the phone album, go to
https://mopria.org/print-from-android to download the
APP and see how to use it.
Print from iOS Device
Make sure that the device is connected to the printer Wi-Fi
hotspot, and the Wi-Fi hotspot indicator lights on in blue.
Conrm that you agree to use this network.
Methods
Print with "Liene Photo" APP
Print from Android Device
Print from iOS Device
Print via USB from a computer
Print via Wi-Fi from a computer
1
2
3
4
5
2
3
How to print
10
Open the album and select the photos, then select the printer,
adjust the printing parameters and print.
Note: USB printing is supported for Mac computers.
Print via USB from a computer
Go to https://global.liene-life.com/pages/download to
download the driver for Photo Printer Series and install it.
Connect the printer to the computer using a USB cable. Select
the photos, click "Print", and select "Liene Photo Printer".
Print via Wi-Fi from a computer
Go to https://global.liene-life.com/pages/download to
download the driver for Liene Photo Printer Series and install
it.
After the computer has successfully connected to the printer
Wi-Fi hotspot, follow the steps in the table below to set the
printer connection.
After successful connection, select the photos, click “Print”, and
select “Liene Photo Printer[xxxx]-Wi-Fi”.
Windows 8/8.1
Click "Control Panel" > "Hardware and
Sound" > "Devices and Printers" > "Add a
Printer", and select "Liene Photo Printer
[xxxx]-WiFi"
4
5
Note: Please make sure that the computer is
connected to the printer Wi-Fi hotspot. [xxxx] refers
to the last four digits of product SN number, which
can be found on the label at the bottom of printer.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Impresora de Liene
