LG M4213C Manual de usuario
Order Number : GETEC-C1-09-152 FCC Class B Certification
Test Report Number : GETEC-E3-09-082 Page 1 / 1
EUT Type: LCD Monitor
FCC ID.: BEJM4213CG
APPENDIX G
: USER’S MANUAL
Make sure to read the
Safety Precautions
before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your dealer when you ask
for service.
M4213C
User’s Guide
Sellers or users should understand that this device is for public use,
not home use.
1
- Only on some models.
Connecting
the stand
First, check if the following parts are all present.
Stand (1)
Screws (6)
Parts
1. Take the parts for the stand out of the box and assemble them as
shown in the picture.
2. Place a soft cloth on the table and put the product with the screen
facing downward. Connect the stand as shown in the following picture.
cable management (1)
3. Use the screws to secure the stand on the rear side of the product as shown
in the diagram.
2
Connecting the Speakers
Mount the product onto the speaker by using a screw as shown in the following
connect the speaker cable.
- Only on some models.
When the speaker is installed.
*Connect the input terminal with a proper color match.
Remove the paper.
Cable holder
After installing your speakers, use holders and cable ties to organize the speaker cables.
* This feature is not available in all model.
Cable tie
* This feature is not available in all model.
3
To install Portrait
- Only on some models.
"When installing Portrait, rotate it clockwise based on its front."
6
Name and Function of the Parts
Rear View
*LINE OUT
A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that
the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of
PC sound card has only Speaker Out, reduce the PC volume.
If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using
the card jumper of the program (Refer to the Sound Card Manual).
* The product image in the user’s guide could be different from the actual image.
Power Connector : Connect the power cord
RS-232C Serial Ports
RGB PC, HDMI/DVI Ports
-HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content
Protection). Some devices require HDCP in order to display HD signals.
PC Sound Jack
: Connect the audio cable to the *LINE OUT jack of the PC sound card.
Wired Remote Control Port
AV Ports
LAN Port
Speaker Ports
AVIN/OUT
AV IN/OUT
7
AVIN/OUT
MAC
Macintosh Adapter (not included)
Use the standard Macintosh adapter since an incompatible
adapter is available in the market. (Different signaling system)
Rear side of the product.
Connecting to External Devices
Connect the power cord.
B
A
B
A
PC
When Connecting to your PC
PC/
MAC
PC
Rear side of the product.
Rear side of the product.
PC
Rear side of the product.
Connect the Audio cable.
(not included)
* User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain
standard compliance for the product.
First of all, see if the computer, product and the peripherals are turned off.
Then, connect the signal input cable.
When connecting with the D-Sub signal input cable.
When connecting with the HDMI to DVI signal input cable (not included).
* When HDMI PC is used, a compatibliy problem might occur.
9
• Using LAN establishes communication between your PC and the monitor and enables to
use the OSD menus on the PC as well as on the monitor.
Connecting to External Devices
Connect the LAN cable as shown in the below figure .
Connect the LAN cable and install the eZ-Net Manager program on the CD-ROM.
For more information about the program, please refer to eZ-Net Guide in the enclosed
CD-ROM.
When using the LAN
Connect PC to Monitor directly
AUsing a router(Switch)
B
PC PC
Product
Using the Internet
C
PC
Product
Network
Product
LAN
LAN
Switch
Note
10
Use this function when displaying ANALOG RGB inputs of a PC to the other product.
RGB IN
RGB OUT
RGB IN
RGB OUT
RGB IN
RGB OUT
RGB IN
RGB OUT
Product 1
•
To use different products connected to each other
Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT
connector of product 1 and connect the other end to the RGB IN connector of other
products.
Daisy Chain Monitors
PC
Product 2 Product 3 Product 4
15-pin D-Sub Signal Cable
Connecting to External Devices
•When multi-connecting in/out cascade format, no loss cables are recommended.
We recommend that you should use cable distributor.
Note
PC
11
The Set is equipped with a kensington Security
System connector on the back panel. The cable and
lock are available separate and are not sold by LG.
For more info, visit http://www.kensington.com, the
internet home page of the Kensington company.
VESA FDMI wall Mounting
This product supports a VESA FDMI compliant mounting interface. These mounts are purchased
separately and not available from LG. Refer to the instructions included with wall mount for more info.
Connecting to External Devices
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Monitor de LG
LG
LG 27HJ712C Manual de usuario
LG
LG 38WR50MS Manual de usuario
LG
LG 910BK Manual de usuario
LG
LG UltraGear 24GL600F-B.BFB Manual de usuario
LG
LG UltraGear 27GN800-B.AEU Manual de usuario
LG
LG 32SQ780S-W.AEU Manual de usuario
LG
LG 34WQ75X-B Manual de usuario
LG
LG 32HL512D Manual de usuario
LG
LG 27UP55NP Manual de usuario
LG
LG 24BQ55WY-B.AEU Manual de usuario
LG
LG M3201T-BA Manual de usuario
LG
LG 24EN43TS Manual de usuario
LG
LG 19M35A Manual de usuario
LG
LG 34BQ77QB Manual de usuario
LG
LG UltraGear 27GN75B-B.AUB Manual de usuario
LG
LG UltraGear 27GP83B-B Manual de usuario
LG
LG FLATRON M4201C Manual de usuario
LG
LG Flatron L1750B Manual de usuario
LG
LG 43UD79-B Manual de usuario
LG
LG W2243C Manual de usuario
