LG FLATRON LCD 568LM Manual de usuario
2001 PCTEST LAB
ATTACHMENT J — USER’S MANUAL
P/NO : 3828TUL193T (S-0107) Printed in Korea
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this
information to your dealer when you require service.
http://www.lge.com
Color Monitor
LCD 568LM
User’s Guide
A1
Introduction
The Monitor has an active matrix TFT (Thin-Film Transistor) LCD (Liquid
Crystal Display).
This monitor is designed for use in small working areas or for those who need
more working space on the desk.
Features
The Monitor is a 15inch (15 inches viewable) intelligent micropro-cessor based
monitor.
Digitally controlled auto-scanning is done with the microprocessor for horizontal
scan frequencies between 31 and 61kHz, and vertical scan frequencies
between 56 and 75Hz.
The microprocessor-based digital controls allow you to adjust conveniently a
variety of image controls by using the OSD (On Screen Display).
The monitor is shipped with 14 factory pre-programmed video modes that are
permanently resident. In addition, there are 16 user-storable modes, for a total
of 30 memory modes.
Plug and play capability if supported by your system.
This monitor has DDC 2B function.*
Compliant with the following regulated specifications :*
-
EPA ENERGY STAR
-
Swedish TCO’99
ENGLISH
*
For detailed information, please refer to the Reference Guide provided .
Connecting the Monitor
A2
To set up the monitor, ensure that the power is turned off to the monitor,
computer system, and other attached devices, then follow these steps:
Place the monitor in a convenient, well-ventilated location near your computer.
Power off both the monitor and Computer.
Slightly press and pull the latch on Stand cover.
Connect the end of monitor signal cable to the connector at the rear panel
of your monitor throught the slot and cable holder on Stand. Connect the other
end to the 15-pin connector on the rear panel of the computer and tighten the
screws. Be sure the signal cable aligns with the 15-pin connector.
Connect the end of monitor signal cable to the connector at the rear panel
of your monitor throught the slot and cable holder on Stand. Connect the other
end of the monitor signal cable to the rear panel of Macintosh computer
through a Macintosh adapter and then tighten screws.
Connect the plug from the AC adapter into the base of the monitor.
Connect one end of the AC power cord to the AC adapter and the other
end to a properly grounded AC outlet that is easily accessible and close to the
monitor.
After connecting cables, put stand cover correctly into the holes unders stand.
If securely connected, you can hear click sound from the latch.
Power ON the PC, then the monitor.
If you see the NO SIGNAL message, check the signal cable and connectors.
After using the system, power OFF the monitor, then the PC.
4
3
2
1
1
IBM PC
MACINTOSH
D-15P
Mac Adapter
1
2
3
4
4'
5
6
7
8
9
24V
AUDIO
DCOUT
Power Cord
Signal Cable AC adapter
D-15P
3
4
1
2
Stand cover
Latch
*NOTE : If you see the “OUT OF
RANGE” message, check to make
sure your system is set to one of the
factory preset modes.(see page A9)
A3
Connecting the Monitor
24V
AUDIO
DCOUT
Connection the Audio
A4
Location and Function of Controls
Rear View
Front View
AUTO
VOL
MUTE MENU
SET
24V
AUDIO
DCOUT
D-Sub Signal Connector
Stand Cover
Power Button
Power Indicator
MENU Button
MUTE Button
Buttons
AUTO/SET Button
DC Power Connecter
-+
12V
VESA wall mounting
Connected to another
object (stand type and
wall-mounted type
- optional)
Kensington Security Slot
Connected to a locking
cable that can be
purchased separately at
most computer stores
NOTE : This monitor accept a 75mm x 75mm VESA-compliant mounting interface pad.
A5
Control Panel Function
Front Panel Controls
AUTO
VOL
MUTE MENU
SET
Use this button to enter and from the on
screen display (OSD).
Use this button to turn the audio on or off.
Use these buttons to choose or adjust items in
the on screen display.
MENU Button
MUTE Button
Buttons
This indicator lights up green when the
monitor operates normally. If the monitor is in
DPM (Energy Saving) mode (stand-by/
suspend/power off), this indicator color
changes to amber.
Power (DPMS)
Indicator
Use this button to turn the monitor on or off.Power Button
Use this button to enter a selection in the on
screen display.
* AUTO adjustment function
Touch the AUTO/SET button before using OSD menu.
This button is for the automatic adjustment of the screen
position, clock and phase.
Note: Some signal from some graphics boards may not function
properly. If the results are unsatisfactory, adjust your monitor’s
Position, Clock and Phase manually.
AUTO/SET
Button
Control Function
MUTE Button
MENU Button AUTO/SET Button
Power Button
Power (DPMS) Indicator
Buttons
PROCESSING
AUTO CONFIGURATION
MENU
MUTE
VOL
AUTO
SET
A6
Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system. A
quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the Buttons. When the icon you want
becomes highlighted, press the AUTO/SET Button.
Use the Buttons to adjust the item to the desired level.
Accept the changes by pressing the AUTO/SET Button.
Exit the OSD by Pressing the MENU Button.
On Screen Display (OSD) Control Adjustment
NOTE
Allow the monitor to stabilize for at least 30 minutes before making image adjustment.
1
1
2
3
4
5
6
7
1
2
2
3
4
5
6
7
1
2
3
3
4
5
6
7
1
2
3
4
4
5
6
7
1
2
3
4
5
5
6
7
A7
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selection and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the items that are shown on the Menu.
OSD Adjust Description
88
100
BRIGHTNESS CONTRAST
9300K 6500K
COLOR
PRESET
RED
GREEN
BLUE
61
39
POSITION
Brightness
Used to adjust the brightness of the
screen.
Contrast
Adjust the display to the contrast
desired.
PRESET
RED
GREEN
BLUE
9300K/ 6500K
To appear the displays color
temperature.
•9300K:Slightly bluish white.
•6500K:Slightly reddish white.
To set your own color levels.
To set your own color levels.
To set your own color levels.
Vertical Positio
To move image up and down.
Horizontal Position
To move picture image left and right.
Tabla de contenidos
Otros manuales de Monitor de LG
LG
LG UltraGear 27GP750-B.AMA Manual de usuario
LG
LG 45GR75DC Manual de usuario
LG
LG L1530TM Manual de usuario
LG
LG 65TR3BF-B Manual de usuario
LG
LG 24MB35DM Manual de usuario
LG
LG M198WDP Manual de usuario
LG
LG FLATRON F720BL-AL E Series Manual de usuario
LG
LG 60PZ9M Manual de usuario
LG
LG 55EJ5C Guía de inicio rápido
LG
LG M4225CCBA Manual de usuario
LG
LG Flatron M1717A Manual de usuario
LG
LG D2343PB Manual de usuario
LG
LG 27UD58P Manual de usuario
LG
LG 22MP58A Manual de usuario
LG
LG WK9 Hoja de especificaciones
LG
LG UltraGear 34GL750 Manual de usuario
LG
LG UltraGear 27GR95QE Manual de usuario
LG
LG Cloud Device 24CK560N-3A.AEU Manual de usuario
LG
LG L2000C - - 20.1" LCD Monitor Guía de inicio rápido
LG
LG Flatron L206WTQ Manual de usuario
