LG 563LE Manual de usuario

Introduction

The 563LE Flat Panel Monitor has an active matrix TFT (Thin-Film

Transistor) LCD (Liquid Crystal Display).

This monitor is designed for use in small working areas or for those who need

more working space on the desk.

Features

The 563LE is a 15.0-inch (15.0 inches viewable) intelligent micropro-cessor

based monitor.

Digitally controlled auto-scanning is done with the microprocessor for horizontal

scan frequencies between 31 and 61kHz, and vertical scan frequencies

between 56 and 75Hz.

The microprocessor-based digital controls allow you to adjust conveniently a

variety of image controls by using the OSD (On Screen Display).

The monitor is shipped with 14 factory pre-programmed video modes that are

permanently resident. In addition, there are 16 user-storable modes, for a total

of 30 memory modes.

Plug and play capability if supported by your system.

This monitor has DDC 2B function.*

Compliant with the following regulated specifications :*

EPA ENERGY STAR

Swedish TCO’99

ENGLISH

For detailed information, please refer to the Reference Guide provided .

Connecting the Monitor

On the back of the monitor are two plug-in connections; one for the AC

power cord, and the other for the signal cable from the video card.

Power off both the monitor and PC.

Connect the 15 pin VGA connector of the supplied signal cable to the output

VGA video connector on the PC and the matching input connector on the rear

of the monitor. The connectors will mate only one way. If you cannot attach

the cable easily, turn the connector upside down and try again. When mated,

tighten the thumbscrews to secure the connection.

Locate the appropriate MAC to VGA adapter block at your local computer

store. This adapter changes the high density 3 row 15 pin VGA connector to

the correct 15 pin 2 row connection to mate with your MAC. Attach the other

end of the signal cable to the side of the adapter block with 3 rows.

Connect the attached adapter block/signal cable to the video output on your

MAC.

Connect the plug from the AC-DC adapter into the connector on the display

unit. Connect one end of the AC power cord into the AC-DC adapter.

Plug the other end into a properly grounded three-prong AC outlet.

Power on the PC, then the monitor.

If you see the

NO SIGNAL

message, check the signal cable and

connectors.

After using the system, power off the monitor, then the PC.

Power Cord

Signal Cable

D-15P

IBM PC MACINTOSH

D-15P

Mac Adapter

*NOTE : If you see the “OUT OF

RANGE” message, check to make

sure your system is set to one of the

factory preset modes.(see page A8)

AC-DC adapter

Location and Function of Controls

Rear View

Front View

VESA wall mounting

Connected to another object

(stand type and wall-mounted

type - optional)

Kensington Security Slot

Connected to a locking

cable that can be

purchased separately at

most computer stores

NOTE : This monitor accept a 75mm x 75mm VESA-compliant mounting interface pad.

D-Sub Signal Connecter

ID Label

DC Power Connecter

••

•

Power Indicator

Power Button

AUTO/SET Button

Buttons

OSD Button

OSD

AUTO/SET

•••••

•

Control Panel Function

Front Panel Controls

OSD

AUTO/SET

Use this button to enter and from the on

screen display (OSD).

Use these buttons to choose or adjust items in

the on screen display.

•Brightness and Contrast can be adjusted directly without

entering the On Screen Display (OSD) system. Touch

the buttons to adjust the settings and then

the OSD button to save all changes. The Brightness

and Contrast functions are also available in the On

Screen Display (OSD) menu.

OSD

AUTO/SET

OSD Button

Buttons

This indicator lights up green when the

monitor operates normally. If the monitor is in

DPM (Energy Saving) mode (stand-by/

suspend/power off), this indicator color

changes to amber.

Power (DPMS)

Indicator

Use this button to turn the monitor on or off.Power Button

Use this button to enter a selection in the on

screen display.

* AUTO adjustment function

Touch the AUTO/SET button before using OSD menu.

This button is for the automatic adjustment of the screen

position, clock and phase.

Note: Some signal from some graphics boards may not function

properly. If the results are unsatisfactory, adjust your monitor’s

Position, Clock and Phase manually.

AUTO/SET

Button

Control Function

OSD Button

AUTO/SET Button

Power Button

Power (DPMS) Indicator

Buttons

PROCESSING

AUTO CONFIGURATION

100

Making adjustments to the image size, position and operating parameters of

the monitor are quick and easy with the On Screen Display Control system. A

quick example is given below to familiarize you with the use of the controls.

Following section is an outline of the available adjustments and selections you

can make using the OSD.

To make adjustments in the On Screen Display, follow these steps:

Press the OSD Button, then the main menu of the OSD appears.

To access a control, use the Buttons. When the icon you want

becomes highlighted, press the AUTO/SET Button.

Use the Buttons to adjust the item to the desired level.

Accept the changes by pressing the AUTO/SET Button.

Exit the OSD by Pressing the OSD Button.

On Screen Display (OSD) Control Adjustment

NOTE

Allow the monitor to stabilize for at least 30 minutes before making image adjustment.

OSD

AUTO

SET

AUTO

SET

On Screen Display(OSD) Selection and Adjustment

You were introduced to the procedure of selection and adjusting an item

using the OSD system. Listed below are the icons, icon names, and icon

descriptions of the items that are shown on the Menu.

OSD Adjust Description

100

BRIGHTNESS CONTRAST

9300K 6500K

COLOR

PRESET

RED

GREEN

BLUE

POSITION

Brightness

Used to adjust the brightness of the

screen.

Contrast

Adjust the display to the contrast

desired.

PRESET

RED

GREEN

BLUE

9300K/ 6500K

To appear the displays color

temperature.

•9300K:Slightly bluish white.

•6500K:Slightly reddish white.

To set your own color levels.

Vertical Position

To move image up and down.

Horizontal Position

To move picture image left and right.

On Screen Display(OSD) Selection and Adjustment

OSD Adjust Description

TRACKING

CLOCK

PHASE

LANGUAGE ENGLISH

OSD POSITION

ELAPSED TIME

1024x768/60Hz

PRESET MODE

SETUP

To minimize any vertical bars or

stripes visible on the screen

background.The horizontal screen

size will also change.

To adjust the focus of the display.

This item allows you to remove any

horizontal noise and clear or sharpen

the image of characters.

To choose the language in which the

control names are displayed.

To adjust position of the OSD window

on the screen.

To display the use time of monitor

LANGUAGE

OSD POSITION

ELAPSED TIME

CLOCK

PHASE

Video Memory Modes

The monitor has 30 memory locations for display modes, 14 of which are

factory preset to popular video modes.

Display Modes (Resolution)

User Modes

Modes 15-30 are empty and can accept new video data. If the monitor detects a

new video mode that has not been present before or is not one of the preset

modes, it stores the new mode automatically in one of the empty modes starting

with mode 15.

If you use up the 16 blank modes and still have more new video modes, the

monitor replaces the information in the user modes starting with mode 15.

640 x 350

720 x 400

640 x 480

800 x 600

832 x 624

1024 x 768

31.47

35.00

37.86

37.50

35.16

37.88

48.08

46.88

49.72

48.36

56.48

60.02

Display Modes (Resolution) Horizontal Freq.(kHz) Vertical Freq.(Hz)

VGA

MAC

VESA

MAC

VESA

Troubleshooting

Check the following before calling for service.

Display Position is incorrect.

Push the AUTO/SET Button.

If the results are unsatisfactory, adjust the image position using the H position

and V position icon in the on screen display.

On the screen background, vertical bars or stripes are visible.

Push the AUTO/SET Button.

If the results are unsatisfactory, decrease the vertical bars or stripes using the

CLOCK icon in the on screen display.

Any horizontal noise appearing in any image or characters are

not clearly portraid.

Push the AUTO/SET Button.

If the results are unsatisfactory, decrease the horizontal bars using the PHASE

icon in the on screen display.

NO SIGNAL message.

The signal cable is not connected, or is loose. Check and secure the

connection.

OUT OF RANGE message appears.

Picture is blank.

The frequency of the signal from the video card is outside the operating range

of the monitor.

Horizontal Frequency: 31kHz-61kHz

Vertical Frequency: 56Hz-75Hz

*Use the graphics board's utility software to change the frequency setting (Refer to the

manual for graphics board).

*You can change the setup to the supported resolution using the Safe Mode (Press the

F8 key during booting the system).

The power LED is illuminated amber.

The monitor is in its display power management mode.

There is no active signal coming from the PC.

The signal cable is not fastened securely.

Check the computer power and graphics adapter configuration.

The monitor doesn't enter the power saving off mode (Amber).

Computer video signal is not VESA DPMS standard. Either the PC or the video

controller card is not using the VESA DPMS power management function.

A10

Specifications

Type

15.0inch (38.1cm) Flat Panel Active matrix-TFT LCD,

Anti-Glare coating

Viewable Size 15.0inch (38.1cm)

Pixel pitch 0.3 x 0.3mm

Horizontal Freq. 31 - 61kHz (Automatic)

Vertical Freq. 56 - 75Hz (Automatic)

Input Form Separate TTL, Positive/Negative

Signal Input 15 pin D-Sub Connector

Display Area 304 x 228mm / 12.0 x 9.0inch

Input Form

Separate, RGB Analog, 0.714Vp-p/75ohm, Positive

Max VESA 1024 x 768@75Hz

Recommend VESA 1024 x 768@60Hz

Normal ≤33W

Stand-by/Suspend

≤3W

Power Off ≤3W

Width 38.92 cm / 15.95 inches

Height 36.25 cm / 14.24 inches

Depth 18.24 cm / 7.18 inches

DC 12V 3A

Input AC 100-240V 50-60Hz 1.2A~0.6A

Output DC 12V 3A

Net 4.8 kg (10.58 lbs)

Down 5˚

Up 30˚

Operating Condition

Temperature 10 ˚C to 35 ˚C

Humidity 10 % to 80 % non-Condensing

Storage Condition

Temperature -20 ˚C to 60 ˚C

Humidity 5 % to 95 % non-Condensing

NOTE

Information in this document is subject to change without notice.

Display

Sync Input

Video Input

Resolution

Power

Consumption

Dimensions

Power Input

AC-DC Adapter

Weight

Tilt Range

Environmental

Conditions

Tabla de contenidos

Otros manuales de Monitor de LG

LG N1941W-PF - - 18.5" LCD Monitor Manual de usuario

LG IPS224T Manual de usuario

LG 32UN500 Manual de usuario

LG IPS231P Manual de usuario

LG W1643C-PF.AEB-BD Manual de usuario

LG 71PY1M - - 71" Plasma Panel Manual de usuario

LG 34WK95C-W.AUS Manual de usuario

LG UltraFine 24MD4KLB-B Manual de usuario

LG L1752H Manual de usuario

LG 24BK55WP Manual de usuario

LG 42PM1M - - 42" Plasma Panel Manual de usuario

LG Flatron 795FT Plus (FB795E-UA) Manual de usuario

LG Flatron L206WTQ-BF Guía de inicio rápido

LG 24MP60G Manual de usuario

LG PL-D860 Manual de usuario

LG E2441V Manual de usuario

LG N1742LP-BF Manual de usuario

LG 27BN55U Manual de usuario

LG 38WK95C-W.AEU Manual de usuario

LG 32MN600P Manual de usuario

LG E1950SV Manual de usuario

LG 32UD60-B Manual de usuario

LG M2362D Manual de usuario

LG MU-42PZ11, MU-42PZ15 Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación

Sceptre

Sceptre D40 Manual de usuario