LG 32LM340S.ABG Manual de usuario

Tabla de contenidos

Otros manuales de Televisor LED de LG

Manuales populares de Televisor LED de otras marcas

Samsung

Samsung QE43LS03A Manual de usuario

Philips

Philips 55PUS6272/12 Manual de usuario

TCL

TCL L40E3020F Manual de usuario

Seiki

Seiki SC-55AU300 Manual de usuario

Sharp

Sharp AQUOS LC-60LE650U Manual de usuario

Durabase

Durabase L24H472S4VD Manual de usuario

Tesla

Tesla 43K625BUS Manual de usuario

Changhong Electric

Changhong Electric UD55GHE6000Ai Manual de usuario

Sharp

Sharp LC-32LE511E Manual de usuario

Samsung

Samsung The Terrace LST7T Series Manual de usuario

Saba

Saba SB40FDS195 Manual de usuario

Philips

Philips 43PFT5102 Manual de usuario

SWEDX

SWEDX SS-42K15 Manual de usuario

Akai

Akai LT-3222AD Manual de usuario

Bush

Bush DLED55UHDSFIRE Manual de usuario

Philips

Philips 32PFL3078K/12 Manual de usuario

Philips

Philips 4111 Series Manual de usuario

Toshiba

Toshiba 32S255 Series Manual de usuario

User Guide

This is a 「User Guide」 installed on the TV.

The contents of this guide are subject to change without prior notice for quality

improvement.

GP2



 

 

 



 

 



 







GP2

eng

❐Automatically Setting Up Programme

SETTINGS ➾ SETUP ➙Auto Tuning

Automatically tunes the programmes.

1 Select Country where the TV is used. Programme settings change depending

on the country you choose.

2 Initiate Auto Tuning.

3 Select Input Source of your choice.

4 Set Auto Tuning following screen instructions.

✎If Input Source is not connected properly, programme registration may not

work.

✎Auto Tuning only finds programmes that are currently broadcasting.

✎If Lock System is turned on, a pop-up window will appear asking for

password.

GP2

eng

❓Cable DTV Setting option

When searching for programmes using FULL setting it can take a long time. The

following values are needed in order to search all available programmes quickly

and correctly. The commonly used values are provided as “default”.

• Frequency : Enter a user-defined frequency.

• Symbol rate : Enter a user-defined symbol rate (Symbol rate: Speed at which

a device such as modem sends symbols to a channel).

• Modulation : Enter a user-defined modulation. (Modulation: Loading of audio

or video signals onto carrier).

• Network ID : Unique identifier allocated for each user.

• Start Frequency : Enter a user-defined start frequency range.

• End Frequency : Enter a user-defined end frequency range.

GP2

eng

❓Satellite Setting Option

• Satellite : Select your desired Satellite.

• LNB Frequency : Select one value from 9750/10600, 9750/10750, 9750,

10600,10750, 5150. If you select 9750/10600, 9750/10750(MHz), 22KHz Tone is

disabled. If you cannot find the LNB frequency value from the list, select User

and manually enter the frequency.

• Transponder : Select the transponder you want to tune.

• 22KHz Tone : When using 22KHz Tone switch, select A or B. If you use 22KHz

Tone, Unicable and Motor Type are disabled.

• LNB Power : To enable the power supply for the LNB, select On. If you select

Off, Motor Type is disabled.

GP2

eng

• DiSEqC : When using DiSEqC, select one option from A~D/ToneA~B. If you

use DiSEqC, Unicable and Motor Type are disabled.

• Unicable Settings : Select On to use Unicable and set the Unicable in the

Unicable Setting menu. When Unicable is enabled, 22KHz Tone, DiSEqC,

Motor Type are disabled.

• Motor Type : Select Motor Type to use Motor and set the Motor in the Motor

Setting menu. When Motor is enabled, 22KHz Tone, DiSEqC, Unicable are

disabled.

✎If you set satellite to others, you must add a transponder using Manual

Tuning.

✎When selecting 22KHz Tone and DiSEqc, you must connect them in the same

position as displayed on the OSD.

✎If you delete a Satellite, all programmes stored in the Satellite are deleted.

GP2

eng

❓Motor Setting Option

• DiSEqC 1.2 : Control motor to change satellite dish position.

Drive Direction : Select the direction in which you want to move the motor.

Drive Mode : Two modes are available: Step and Continuous.

-Step: The motor moves based on the value you ente r (from 1 to 128).

-Continuous: The motor moves continuously until you press the Stop.

Test TP : Select the test TP you want to tune.

Set Limit : Set the motor movement to east or west to have the motor move

only within the direction set.

-On: You can limit the movement to the current direction by selecting the

West/East.

-Off: You can cancel the limit you set.

GP2

eng

Go To Zero: You can move the motor to Zero

Store: You can save the motor’s current direction.

• USALS : Set your current location(Longitude/Latitude).

GP2

eng

❐Cable DTV Setting

SETTINGS ➾ SETUP ➙ Cable DTV Setting

[In Cable, Cable & Satellite mode only]

When Channel Auto Update is On, you can update information for all the

programmes that can be updated, including the programme currently being

watched. When Channel Auto Update is Off, you can only update information for

the programme currently being watched.

✎The range that a user can select from the Service Operator menu differs

depending on number of Service Operator supported by each country.

✎If number of supported Service Operator for each country is 1, corresponding

function becomes inactive.

✎You can not select the Cable DTV Setting when the service operator is set to

“Ziggo”.

GP2

eng

❐Satellite Setting

SETTINGS ➾ SETUP ➙ Satellite Setting

[In Satellite, Antenna & Satellite, Cable & Satellite mode only]

You can add/delete/set the satellite you want.