LG HB9522A Manual de usuario

Built-In Gas Cooktops

Installation and Operating Instructions

HB9522A

To avoid the risk of accidents or damage to the Gas Cooktops,

it is essential to read these operating instructions

before it is installed or used for the first time.

And please keep this manual for later reference.

P/No.: MFL62060301

http://au.lge.com (Australia)

http://nz.lge.com (New Zealand)

Contents

Introduction ................................................................................. 3

1. Instructions for safe and proper use.........................................3

Instructions for the installer ...................................................... 5

2. Positioning of the hob...............................................................5

3. Electrical connection ................................................................9

4. Gas connection ......................................................................10

5. Adaptation to different types of gas........................................12

6. Final operations......................................................................16

Instructions for the user .......................................................... 19

7. Using the hob .........................................................................19

8. Cleaning and maintenance ....................................................21

These instructions are valid only for end user countries whose

identification symbol appear on the cover of this manual.

INSTRUCTIONS FOR THE INSTALLER: these are for the

authorised person who must carry out a suitable check of the gas

system, install the appliance, set it functioning and carry out an

inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the commands and the correct procedures for

cleaning and maintenance of the appliance.

1. Instructions for safe and proper use

This manual is an integral part of the appliance and therefore must

be kept in its entirety and in an accessible place for the whole

working life of the cooking Hob. We advise reading this manual and

all the instructions therein before using the cooking Hob. Also keep

the series of nozzles supplied. Installation must be carried out by

qualified personnel in accordance with the regulations in force. This

appliance is intended for domestic uses and conforms to current

regulations in force. The appliance has been built to carry out the

following functions: Cooking and heating-up of food. All other

uses are considered improper.

The manufacturer declines all responsibility for improper use.

Do not leave the packing in the home environment. Separate the

various waste materials and take them to the nearest special

garbage collection centre.

It is obligatory for the electrical system to be grounded according to

the methods required by safety rules.

The plug to be connected to the power cable and the socket must

be the same type and must conform to current regulations.

Never unplug by pulling on the cable.

Immediately after installation carry out a brief inspection test of

the cooking Hob, following the instructions below. Should the

appliance not function, disconnect it from the supply and call the

nearest technical assistance centre.

Never attempt to repair the appliance.

Always check that the control knobs are in the position

“ZERO”(OFF) when you finish using the hob.

Introduction

The identification plate, with technical data, serial number and

marking is clearly visible under the casing.

The plate on the casing must not be removed.

Before connecting the device, make sure that it has been regulated

for the type of gas that will feed it, checking the label under the Hob.

Do not put pans without perfectly smooth and flat bottoms on the

cooking hob grids.

Do not use pans or griddle plates that extend beyond the external

perimeter of the hob.

The hob is to be used by adults only. Do not let unsupervised

children play with the hob.

This appliance is designed for cooking food and it shall not be used

as a space heater.

Do not spray aerosols in the vicinity of this appliance while it is in

operation.

WHERE THIS APPLIANCE IS INSTALLED IN MARINE

CRAFT OR IN CARAVANS, IT SHALL NOT BE USED AS A

SPACE HEATER.

The manufacturer declines all responsibility for damage to

persons or things caused by non-observance of the above

prescriptions or by interference with any part of the appliance or

by the use of non-original spares.

DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE

APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.

DO NOT MODIFY THIS APPLIANCE

2. Positioning of the hob

This appliance shall be installed only by authorized persons in

accordance with AS5601 - Gas Installations, any statutory regulations,

local gas regulations, municipal building codes, electrical wiring

regulations, and the manufacturer's installation instructions.

Clearance around the appliance must comply with the requirements of

AS5601.

The following operation requires building and/or carpentry work so

must be carried out by a competent tradesman. Installation can be

carried out on various materials such as masonry, metal, solid wood or

plastic laminated wood as long as they are heat resistant (T 90°C).

2.1 Attachment to support structure

Create an opening with the dimensions shown in the figure in the top

surface of the counter, keeping a minimum distance of 50 mm from the

rear border.

This appliance is classified as “type Y” in relation to fire hazards and

can therefore be mounted against walls higher than the work surface on

condition that a certain distance “X” be kept between the appliance and

the wall as shown in the figure so as to avoid damage from overheating.

Make sure there is a minimum of 750 mm between the hot plate flames

and any shelf that may be installed directly above them.

Carefully position the insulating seal supplied on the outer perimeter of

the hole made in the counter top as shown in figure 4 (the dimensions

in the figure refer from the hole to the inside of the seal), trying to

ensure that it sticks across the whole of its surface by applying light

pressure with your hands. Fix the hob to the unit using the appropriate

Instructions for the installer

brackets Band spacers Aas shown in graphics 1, 2 and 3. Spacers A

will help to keep the hob top at the right distance from the edge of the

counter top to avoid future overheating during operation. Carefully trim

the surplus away from edge Cbeyond the seal (Fig.5).

Overall dimensions: location of gas and electrical connection

points (all measures in mm).

2.2 Clearance above and around domestic appliances

Extract from AS5601

REQUIREMENTS

1. Overhead clearances – (Measurement A)

Range hoods and exhaust fans shall be installed in accordance with

the manufacturer’s instructions. However, in no case shall the

60 cm 90 cm

hob hob

A 35 105

B65 50

C30 50

D85 75

Dimension A, C : Clearances are

these for the hose assembly.

Instructions for the installer

clearance between the highest part of the hob of the cooking

appliance and a range hood be less than 600 mm or, for an

overhead exhaust fan, 750 mm.

Any other downward facing combustible surface less than 600 mm

above the highest part of the hob shall be protected for the full width

and depth of the cooking surface area in accordance with Clause

5.12.1.2. However, in no case shall this clearance to any surface be

less than 450 mm.

2. Side clearances – (Measurements B& C)

Where B, measured from the periphery of the nearest burner to any

vertical combustible surface, is less than 200 mm, the surface shall

be protected in accordance with Clause 5.12.1.2 to a height C of not

less than 150 mm above the hob for the full dimension (width or

depth) of the cooking surface area. Where the cooking appliance is

fitted with a ‘splashback’, protection of the rear wall is not required.

3. Additional requirements for Freestanding and Elevated Cooking

Appliaces – (Measurements D& E)

Where D, the distance from the periphery of the nearest burner to a

horizontal combustible surface is less than 200 mm, then Eshall be

10 mm or more, or the horizontal surface shall be above the trivet.

See insets above.

NOTES

1. Requirement 3 does not apply to a freestanding or elevated cooking

appliance which is designed to prevent flames or the cooking

vessels from extending beyond the periphery of the appliance.

2. The ‘cooking surface area’ is defined as that part of the appliance

where cooking normally takes place and does not include those

parts of the appliance containing control knobs.

3. For definition of hob, see Clause 1.4.64.

4. For definition of trivet, see Clause 1.4.109.

5. Consideration is to be given to window treatments when located near

cooking appliances. See Clause 5.3.4.

3. Electrical connection

Make sure that the voltage and capacity of the power line conform

to the data shown on the plate located under the casing. Do not

remove this plate for any reason.

The plug on the end of the supply cable and the wall socket must

be the same type and conform to the current electrical system

regulations.

Check that the power line is adequately grounded.

On the power line, install an omnipolar cut-off device with contact

cut-off distance greater than or equal to 3 mm, located in an easily

accessible position near the unit.

Do not use reducers, adapters or shunts.

If the power cable is replaced, the wire section on the new cable

must not be less than 1 mm2(3 x 1 cable), keeping in mind that

the end to be connected to the hob must have the ground wire

(yellow-green) longer by at least 20 mm. Use only H05V2V2-F

cable or similar which has a maximum temperature of 90°C.

Any replacement needed should be carried out by a specialised

technician who should make the mains connections according

to the following diagram.

L= brown

N= blue

= yellow-green

The manufacturer will not be liable for any damage to persons

or property caused by non-observance of the above instructions

or deriving from the tampering of even a single part of the hob.

4. Gas connection

Use pipe-joint compound made for use with Natural U.L.P. gas.

The burner it controls is shown next to each knob (the

example corresponds to the front left burner).

This appliance is suitable for installation with Natural Gas

or ULPG (propane). Refer to page 12 for the relevant

burner pressure and appropriate injector sizes. When the

appliance is to be connected to Natural Gas then the

pressure regulator supplied must be fitted to the gas inlet.

A test point (for checking the gas pressure) is supplied

either with the regulator or as a separate fitting in the case

of ULPG (propane) appliances.

Connection of the appliance to the gas supply must be in accordance

with the requirements of AS5601. A 1/2” BSP connector at the inlet is

recommended and the gas supply line to the appliance must be of

adequate length to allow sufficient withdrawal of appliance for service

or disconnection and be:

1. annealed copper pipe or;

2. flexible hose according to AS/NZ1869 & be at least Class “B”,

10 mm diameter.

The appliance must be installed with provision to allow the gas to be

turned off and disconnected for servicing and removal of the appliance

as required from the gas supply.

Before the appliance is operated make certain all relevant parts are

placed in the correct position.

When the installation is completed the installation connections of

appliance will require to be leak tested, the burner operating pressure

and flame checked and adjusted.

Warranty service calls do not cover these adjustments!

To check the operating pressure of the appliance it is recommended at

least 2 large size burners are used. Ensure appliance is secured to wall

when installation is completed.

N.G. The regulator supplied must be fitted to the 1/2BSP thread at the

rear of the appliance. An approved manual shut-off valve must be

Instructions for the installer

Tabla de contenidos

Otros manuales de Placa de cocina de LG

LG CBGS3028S Manual de usuario

LG LCG3611ST Manual de instrucciones

LG CBGJ3027 Series Manual de usuario

LG LCG3091ST - 30" Gas Cooktop Manual de usuario

LG LCG3091 Series Manual de usuario

LG LCG3691ST - 36" Gas Cooktop Manual de usuario

LG LCE3081ST - 30in Smoothtop Electric Cooktop 5 Steady Heat... Manual de usuario

LG Studio LSCE365ST Manual de usuario

LG LCE3081ST - 30in Smoothtop Electric Cooktop 5 Steady Heat... Manual de usuario

LG LCG3691ST - 36" Gas Cooktop Manual de usuario

LG LCG3091ST - 30" Gas Cooktop Manual de usuario

LG LCE3681ST - 36in Smoothtop Electric Cooktop 5 Steady Heat... Manual de instrucciones

LG LSCG366ST Manual de usuario

LG LCG3691ST - 36" Gas Cooktop Manual de usuario

LG Studio LSCE365ST Manual de usuario

LG HB6422A Manual de usuario

LG LCG3691ST - 36" Gas Cooktop Manual de usuario

LG LSCG366ST/01 Manual de usuario

LG Studio LSCE305ST Manual de usuario

LG LCG3691ST - 36" Gas Cooktop Manual de usuario

LG LSCE305ST/00 Manual de usuario

LG Studio LSCI307ST Manual de usuario

LG LSCG367ST Manual de usuario

Manuales populares de Placa de cocina de otras marcas

Bonnet

Bonnet OPTIMUM 700 Manual del propietario

Jenn-Air

Jenn-Air JGCP430 Manual de usuario

Frigidaire

Frigidaire FES367FCC Guía de inicio rápido

Ztove

Ztove EZ2 DUO Manual de usuario

Kleenmaid

Kleenmaid cooking GCTK9011 Guía de instalación

Casselin

Casselin CSASRE24 Manual de usuario

Jenn-Air

Jenn-Air JGC2536EB00 Manual de usuario

Waldorf

Waldorf RN8603E-B Manual de instrucciones

Whirlpool

Whirlpool SMP658CNEIXL Manual de usuario

Wolf

Wolf CI243C/B Manual de usuario

Fulgor Milano

Fulgor Milano F5PGK305S1 Manual de usuario

GE JP389 Manual de usuario

Wells

Wells WV-2HFG Manual de usuario

IKEA

IKEA Lagan HGA4K Manual de usuario

Samsung

Samsung NA36N9755 Manual de usuario

Miele

Miele KM 404 Manual de usuario

Lacor

Lacor 69562 Hoja de especificaciones

Keating Of Chicago

Keating Of Chicago MG-2 Manual de usuario