LG CED-8041B Manual de usuario

CH01

LG Electronics Inc.

LG Twin Towers. 20, Yoido-dong, Y oungdungpo-gu,

Seoul, Korea

http://www .lge.co.kr

http://www .LGEservice.com

P/NO:3828HM1014H Printed in K orea

LG Electronics U .S.A. Inc.

1000 Sylvan Ave.Englewood Cliffs

NJ 07632 U.S.A.

LG Electronics Canada Inc.

235 Superior Blvd, Mississauga

Ontario, Canada

LG Electronics Deutschland GMBH

Jakob-Kaiser-Str aße 12,

D-47677 Willich, Germany

LG Electronics U . K. Ltd.

LG House, 264 Bath Road,

Slough Ber kshire SL1 4DT

United Kingdom

LG Goldstar F rance SARL

12, Rue Lech Walesa-Z.I. Pariest

77185 Lognes , France

LG Electronics Italia S .P.A.

Centro Direzione “IL Quadr ate” Via Modigliani,

20090 Segrate (MI) Italy

LG Electronics España

Adva, De Europa, 21

28108 Alcovendas (Madr id) Spain

CED-8041B/

CED-8042B

Deutsch English

Italiano

Spanish

CAUTION : The laser used in the CD-R/RW drive can damage your eyes.

Do not attempt to open the cover.

To reduce the risk of electric shock, do not remove cover (or back).

No user-serviceable parts inside.

Refer servicing to qualified service personnel.

Use of controls or performance of procedures other than those specified

here in may result in hazardous radiation exposure.

WARNING : To reduce the risk of fire or electric shock, do not expose this appliance

to rain or moisture

■PC DOS is a trademark of IBM Inc.

■Adaptec and the Adaptec logo are trademarks of the Adaptec Corporation.

■MS-DOS, Windows, and Windows®95 are trademarks registered in the United States

and other countries by the Microsoft Corporation.

■The company names and product names written in this manual are trademarks or

registered trademarks of the respective companies.

This unit uses CD-RW discs with the following mark.

This unit uses CD-R discs with the following mark.

This unit uses CD-ROM discs with the following mark

When you use this unit as a CD player, use compact discs

with the following mark.

COMPACT

DIGITAL AUDIO

Recordable

COMPACT

ReWritable

8042B intro EES-eng 5/12/89 3:14 PM Page 1

Industry Canada requirement

This class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement

sur le matériel brouilleur du Canada.

FCC COMPLIANCE STATEMENT

Note : This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an Authorized Service Center for help.

• FCC WARNING

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

• This CD-R/RW Drive is for use only with UL listed personal computers that have

installation instructions detailing user installation of card cage accessory.

This product is manufactured to comply with the radio interference requirements

of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/EEC.

English

8042B intro EES-eng 5/12/89 3:14 PM Page 2

CAUTON - INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO

BEAM.

VARNING-OSYNLIG LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD STRÄLEN

ÄR FARLIG.

iii

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

8042B intro EES-eng 5/12/89 3:14 PM Page 3

DirectCDTM v2.5b(s)

Introduction

Installation

Operation

Appendix

Contents

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . 3

System Environment . . . . . . . . . . . . . . . . . . . . . . . . . 4

Location and Function of Controls . . . . . . . . . . . . . . 5

Installing the Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Device Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

How to Use the Discs. . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

* CED-8041B: allows reliable writing at 2X speed only.

* CED-8042B: allows reliable writing at 2X and 4X

speeds.

Writing speed depends on capabilities

of discs. As a result, you should

checked ReWritable 4X speed discs.

8042B EES GUIDE-eng 5/12/89 3:07 PM Page 1

DirectCDTM v2.5b(s) Introduction

Thank you for

purchasing this

CD-R/RW Drive.

Package

Items

Features

• Running OPC* gives a flatter writing signal that improves

reliability.

• An improved anti-heat design means that no cooling fan is

needed.

• Easy-to-use tray model.

• Enhanced-IDE (ATAPI) model.

• Can read not only CD-R and CD-RW discs, but also video CDs,

music CDs, and photo CDs.

• Can read data at 24X speed (3.6MB/sec data transfer rate) and

write data at 4X speed (600KB/sec data transfer rate).

• The recorded CD-RW media can be played in a DVD player or

a multiread CD-ROM Player, maintaining future compatibility.

• Supports UDF for easy writing to CD-RW discs.

* Continuously monitors the signal level during recording and

adjusts the laser power to compensate when the disc is dirty,

insuring a flat signal.

Item Quantity

- Internal CD-R/RW Drive 1

- CD Recording Software 1

- Blank CD-RW Disc 1

- Blank CD-R Disc 1

- Device Driver (MS-DOS) 1

- E-IDE (ATAPI) cable 1

- Audio Cable 1

- Mounting Screws 4

- Manual for CD-R/RW Drive 1

- Manual for CD Recording Software 1

8042B EES GUIDE-eng 5/12/89 3:07 PM Page 2

DirectCDTM v2.5b(s)

Precautions

Installation

Operation

Important Precautions

Follow these precautions when handling the drive or discs.

• Please take notice that the manufacturer of this equipment does

not offer any warranty against data loss due to inappropriate

installation or handling, or direct or indirect damages.

• Please take notice that the manufacturer will bear no

responsibility for direct or indirect damages caused by the use of

this product or its malfunction.

• Please take notice that the manufacturer will bear no

responsibility for damage to data caused by this product.

• Please backup (copy) all important data as protection against

data loss.

• Avoid placing the drive in a location subject to:

- high humidity

- high temperature

- excessive dust

- mechanical vibration

- direct sunlight

We recommend using the drive in a horizontal position.

Do not use it in a tilted or vertical position.

• Don’t move the drive suddenly from a cold place to a warm one or

raise the room temperature suddenly. Condensation may occur,

causing abnormal operation.

• Make sure to remove the disc before moving the drive. The disc

may be damaged, causing data loss.

• Be careful to prevent foreign objects, such as liquids or metal,

from entering the drive. In case a foreign object enters the drive,

please consult the dealer where the drive was purchased.

• Don’t interrupt the electric power while the drive is operating.

• When connecting two IDE devices to the Primary or Secondary

connectors, make sure that the two devices are not configured as

both Master, or both Slave. If they are both set the same,

Windows may fail to run or recognize the drives.

• The total length of the IDE cable should be no more than 18

inches (about 45 cm).

8042B EES GUIDE-eng 5/12/89 3:07 PM Page 3

DirectCDTM v2.5b(s)

Computer

Software

System Environment

This unit can be operated in the system environment explained

here.

❏ Occasionally the CD-R and CD-RW discs written by the CD-

R/RW drive cannot be read by other CD drives*. These

unreadable discs should be read using the CD-R/RW drive on

which require written.

* With Windows NT Workstation Ver. 4.0, the drive is usable only

with Adaptec EASY CD CREATOR.

* The disc written using the CD-R/RW drive might not be

readable by CD-ROMs other than Multi-read compatible (UDF

compatible) CD-ROMs.

Multiread compatible (UDF compatible) CD-ROMs are:

1. CD-ROMs that can read low reflectance.

2. CD-ROMs that support Packet Write.

Install the supplied CD Recording Software before using this unit.

100MHz (or faster) Pentium (for 4x speed,

166MHz or faster recommended)

Windows 98/95 : 32MB or greater.

Windows NT Workstation Ver. 4.0: 32MB or

greater (64MB or over recommended)

Hard disk with average access time of 19 msec

or less, and data transfer speed of 600KB/sec

or greater. 75MB or more free space.

(The free space needed for writing depends on

the quantity of data.)

Enhanced-IDE interface (as Primary Slave,

Secondary Master or Slave)

5.25-inch half-height bay required

+5V/+12V power socket required

Windows 98/95, Windows NT Workstation

Ver.4.0 or later*

CD-R : Ricoh, Mitsubishi Chemical, Verbatim,

Taiyo Yuden, Mitsui Toatsu, TDK, Kodak,

or SKC discs are recommend.

CD-RW : Ricoh, Mitsubishi chemical, Verbatim

discs are recommend.

System

requirements

Hard disk

Interface

Drive bay

Power

Software Required OS

CD-R, CD-RW discs

CPU

Memory

8042B EES GUIDE-eng 5/12/89 3:07 PM Page 4

DirectCDTM v2.5b(s)

Front Panel

Location and Function of Controls

READ

WRITE

COMPACT

Disc Tray

Emergency

Eject Hole

Play/Skip Button

Stop/Eject Button

Headphone Jack Volume

Control Drive Activity Indicators

1. Disc tray

This is the tray for the disc. Place the disc on the ejected disc tray, then

lightly push the tray (or push the eject button) and the CD will be loaded.

NOTE: Don’t pull out or push in the disc tray forcibly. This might cause

damage to the loading section of the drive.

2. Stop/Eject button

Press this button to open the CD tray.

This button works only when power is supplied to the drive.

If an Audio CD is playing, pressing this button will stop it, and pressing it

again will open the tray.

3. Play/Skip button

When an Audio CD is in the disc drawer, pressing this button will start

playingAudio CDs from the first track. If an Audio CD is playing, pressing

this button will skip to the next track.

4. Volume control

Adjust the output volume of the headphone jack with this control. It can’t

be used to adjust the output volume for the audio output connectors on

the rear panel.

NOTE : Turn the volume down before turning on the power. Sudden loud

noises can damage your hearing.

5. Headphone jack

This jack is for connecting headphones or mini-speakers.

6. Drive activity indicators

Two colored LEDs are used to indicate the operation of CD-R/RW Drive.

(1) Read

The orange color is displayed when the spindle motor begins the

Spin up operation: accessing data, reading data, playing Audio, and

up loading tray.

(2) Write

The green color is flashed during disc writing sessions.

8042B EES GUIDE-eng 5/12/89 3:07 PM Page 5

DirectCDTM v2.5b(s)

Rear Panel

DIGITAL ANALOG

INTERFACE POWER

DR CSM

SLA

GLG39

+5 +12

GND

AUDIO AUDIO

Analog Audio Output

Connector

Jumper Connector Power

Connector

Digital Audio

Output Connector

IDE Interface Connector

1. Power Connector

Connects to the power supply (5-and 12-V DC) of the host computer.

NOTE : Be careful to connect with the proper polarity. Connecting the

wrong way may damage the system (and is not guaranteed). Usually this

connector can only be attached one way.

2. IDE Interface Connector

Connect to the IDE (Integrated Device Electronics) Interface using a 40-

pin flat IDE cable.

NOTE : Do not connect or disconnect the cable when the power is on,

as this could cause a short circuit and damage the system. Always turn

the power OFF when connecting or disconnecting the cable.

3. Jumper Connector

This jumper determines whether the drive is configured as a master or

slave. Changing the master-slave configuration takes effect after power-

on reset.

4. Analog Audio Output Connector

Provides output to a sound card (analog signal). Generally you need this

to play a regular audio CD.

5. Digital Audio Output Connector

Provides output to a sound card (digital Signal).

8042B EES GUIDE-eng 5/12/89 3:07 PM Page 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de CD/CDR de LG

Manuales populares de Unidad de CD/CDR de otras marcas

Philips

Philips CDD3610 Manual de usuario

QPS

QPS Que!Fire Manual de usuario

Plextor

Plextor 12X-3 Guía

Samsung

Samsung SN-324B Manual de usuario

Teac

Teac CD-211E Manual de usuario

SmartDisk

SmartDisk Firewire CD-R/W Manual de usuario

Axis

Axis CD-ROM SERVER Manual de usuario

Memorex

Memorex 32023234 - 52x32x52x External USB2.0 CD... Instrucciones de instalación

Yamaha

Yamaha CD Recordable/Rewritable Drive CRW3200 Manual de usuario

Sony

Sony CRX230AE Manual de usuario

Sony

Sony CRX - 160E Manual de usuario

Panasonic

Panasonic KX-LD742 Manual de usuario

Pioneer

Pioneer BDR-S13U-X Manual de usuario

Panasonic

Panasonic LK-MC606BP Manual de usuario

Panasonic

Panasonic CF-VCW Series Manual de usuario

Conner

Conner CFP2107 Series Manual de usuario

Sony

Sony CRX-1611 Manual de usuario

Plextor

Plextor 12-20C Guía